High Strength Epoxy Resin Fiberglass Cross Knitting+ Pultrusion Insulation Tube was widely used for the live line tools and other insulation parts which need the better electrical performance and light weight.
1. Standard: GB13398-2008 , IEC 60855.
2. Material: Fiber glass and epoxy resin. Filled by close cell foam.
3. Process:Continuous knittingfiberglass + pultrusion.process.
Low dielectric loss glass fiber
Low dielectric names D glass fiber, have D3, Dk series. It is low density, low dielectric constant and low dielectric loss. It is an ideal reinforcement for making light weight and high performance radomes with high wave permeability and wide frequency band and print circuit board etc...
Specifications D glass fiber
Items,D3,Dk
Density g/cm3,2.30,2.30
Strength of virgin filament Mpa,2600,2600
Elastic modulus GPa,55,55
Dielectric constant 2210,10HZ,4.5,5.0
Dielectric loss 2210,10HZ,0.0035,0.0035
D glass fiber fabric
Specification,D3,Dk
Thickness mm,0.22,0.22
Weight g/m2,210,210
Breaking strength N/100*25,Warp,1350,1450
,Weft fill,1000,1050
Silicone Rubber Fiberglass sleeving - temperature resistance of - 30 ~ 200 , pressure resistance of 1.2kv-2.5kv (inner fiber and outer glue) - temperature resistance of - 30 ~ 200 , pressure resistance of 4.0kv. The surface of tightly woven glass fiber sleeve is dipped with complete silica gel and cured at high temperature. (outer fiber and inner rubber) - glass fiber sleeve with temperature resistance of - 30 â?? ~ 200 â?? and pressure resistance of 7.0kv woven tightly on the surface of silicone rubber pipe. Srg-n meets the requirements of Part 1 of the Canadian Electrical Code code and the requirements of coated electrical insulating sleeves for higher temperature applications specified by the National Institute of standards and chapter 1.4 of the National Fire Protection Association electrical code. The long-term aging test meets the requirements of ul746b or CSA c22.2 chapter 0.17. It is widely used in internal wiring harness and insulation protection of H & n automobile, shipbuilding, motor, household appliances, electric heating equipment, special lamps, TV and electronic instruments.
Srg-w is mainly used in the transportation of high temperature and high pressure fluid and the equipment and instruments that need soft, wear-resistant insulation and mechanical protection.
Glass fiber tube is also called glass fiber tube, glass fiber sleeve, which is a special glass fiber sleeve which is made of glass fiber woven into pipe and treated by high temperature setting process; Glass fiber tube is divided into silicone glass fiber tube and silicone rubber glass fiber tube.
Silicone glass fiber tube, also known as silicon casing or self quenching tube, is made by weaving alkali free glass fiber into a tube and then dip and coat silicone resin, and heat and cure it. The silicone rubber glass fiber tube is composed of high quality silicone rubber layer and glass fiber braid layer, which can be divided into two types: inner rubber outer fiber glass fiber tube and inner fiber outer rubber glass fiber tube. According to the voltage resistance grade, fiberglass pipes can be divided into 1.5kV glass fiber pipe, 2.5KV glass fiber pipe, 4KV glass fiber pipe and 7kv glass fiber tube.
Zhejiang Yingtai Insulation Material Co., Ltd. is a manufacturer mainly producing epoxy glass fiber winding pipes. It has a complete set of manufacturing process line equipment and machinery. Our products are all customized products. Various specifications can be customized according to customer requirements. Various types of epoxy glass fiber wound pipe.
   Epoxy glass fiber winding pipe is made by uninterrupted fiber wet winding. It is specially developed for high-voltage electrical equipment structural components such as reactors, arresters, fuses, transformers, on-load tap-changers, and transformers. The product performance parameters meet IEC standards Requirements, the product is leading in China.
Basic parameters:
1: winding angle, 45 65 (the winding angle can be adjusted according to different requirements to achieve better mechanical performance requirements);
2: fiber content (weight ratio), 70 to 75%;
3: density, 2.00 g / cm3;
4: water absorption, less than 0.03%;
5: Axial thermal expansion coefficient, 1.8 E-05 1 / K;
6: Glass transition temperature, 110 120 ;
7: Chemical resistance Mineral oil: Excellent;
8: solvent and dilute acid: excellent;
9: tensile elastic modulus, 14000 MPa in the axial direction;
10: tensile strength; axial 280 MPa; hoop 600 MPa;
11: Shear strength: 150 MPa;
12: Bending strength: 350 MPa in the axial direction;
13: Compressive strength: 240 MPa in the axial direction;
14: relative dielectric constant 2-3.2;
15: Dielectric loss factor 0.003-0.015;
16: partial discharge â?¤5;
17: Insulation strength: 3 to 6 kV in the axial direction; 10 to 12 kV in the radial direction;
18: Lightning shock: 110 KV
19: Power frequency shock: 50 KV;
20: Heat-resistant grade: B, F, H
21: inner diameter> 5mm; outer diameter
1245 Fiberglass Suppliers
Short on time? Let Fiberglass sellers contact you.
FRP Fiberglass Grating Advantages:
* Excellent Corrosion Resistance
* 65% Lighter than Steel
* Impact Resistant, high strength
* Non-Conductive
* Long maintenance-free life
* Light and Easy to Fabricate
* Transparent to Radio Waves and EMI/RF Transmissions
CYC FIBERGLASS ROVING FOR FRP FILAMENT WINDING
CYC Fiberglass Roving for FRP Filament Winding is finished with high performance sizing and compatible with unsaturated polyester(UP), polyurethane, vinyl ester (VE), epoxy (EP) and phenolic resins. It is designed for filament winding process specially and provide fast wet-out in multiple resins with excellent mechanical properties. The typical end-finished products are including FRP water pipes, high pressure oil pipes, chemical corrosion resistant pipes, pressure vessels, gratings, chemical storage tanks, automobile parts, cable trays and other insulation industries.
Glass Type: E-CR Glass
Roving Type: Singe-end Roving, Direct Roving, Multi-ends Roving, Assembled Roving
PRODUCT FEATURES
Good strand integrity and even tension
Fast wet-out in resin with low resin consumption
Inner side unwinding smoothly & low fuzz
Excellent tensile strength and mechanical properties
TYPICAL PRODUCT SPECIFICATIONS
Product Code Filament Diameter (�¼m) Linear Density (tex) Tensile Strength (N/tex) Moisture Content (%) Loss On Ignition (%) Compatible Resin
ECY150DF 13~24 600, 1200, 2400 4800, 9600 0.40 0.20 0.55±0.15 UP
VE
ECY280DF 13~17 1200, 2400, 4800 0.40 0.20 0.55±0.15 UP
EP
CYC Fiberglass Direct Roving (ECY150D) for FRP Pultrusion
CYC Fiberglass Roving for FRP Pultrusion is finished with high performance silane sizing and compatible with unsaturated polyester(UP), polyurethane, vinyl ester (VE), epoxy (EP) and phenolic resin matrixes. It is designed for weaving, filament winding, pultrusion, extrusion and hand lay-up processes. The typical end-finished products are including various FRP/GRP pipes, pressure vessels, gratings, chemical storage tanks, automobile parts, cable trays and so on.
Glass Type: E-CR Glass
Filament Diameter: 13, 15, 17, 24, 31�¼m
Linear Density: 300, 600, 900, 1200, 2400, 4800, 9600tex
Product Features:
Good strand integrity and even tension
Fast and complete wet-out in resins.
Inner side unwinding smoothly & no fuzz
Excellent tensile strength and mechanical properties
fiberglass needle mat is a good thermal and voice insulation material
A.Density toralence +15%-10%
B. Heat Resisting 700C degree.Softening temperature: 850 C
C.High tensile strength: 350kg/mm ,Modules of elasticity:7300kg/mm ,Elongation at 25 C:4.8%,Flexible: conforms to irregular surfaced
D.Corrosion Properties:does not absorb water,rot,mildew,deteriorate or decay.
E. Application:Applications Muffler and exhaust insulation ,Automotive catalytic converter, flooring and front dash insulation ,Removable pads,Ship turbines ,Marine, industrial, and process piping ,Power generating equipment,Industrial furnaces and ovens ,Filtration ,Gaskets for air conditioning
The fiberglass window screen is produced with the fiberglass yarn through coating processing and then woven by a method of the plain weave in the production line. The finished screen features good performance for air ventilation and solar shade. As well, it possesses many advantages in terms of anti-corrosion and heat insulation, being easy to clean without deformation, long service life as well as fine and smooth feeling in the hand. It has been widely used in various facilities in ventilation, insects, mosquitoes and flies control.
FRP molding multiple links is the connector of FRP handrail and fences, which is widely used in public facilities. Its regular size is diameter 50mm, and the other size can be made by order.
FRP profiles is made of fiberglass and resin with pultrusion process. It has the character with light weight, alkali resistant, high strength. And it can provide many shape and sizes with various colors. It is widely used in public facilities.
FRP molded grating is made of fiberglass and resin by the molding process. It is used in chemical plant, sewage system etc. Its mesh size and panel size is regular and the color is variable.
This is Jack from China and we are the professional manufacturer of Fiberglass Mosquito Screen.
Pls kindly check more details as following
Weight: 80-120gsm
Mesh:18x16 mesh, 18x14 mesh, 16x16 mesh, 16x14 mesh, 14x14 mesh and so on
Color: Black,gray,green or as your requirement
Package: per roll with plastic bag,6 rolls with one carton or as your requirement.
Quantity:20' Container Could load 80000 Square Meters
And we would like to send you samples to test the quality.
There are many types and specifications of fiberglass net. Generally the mass from 60 g/sq m up to 500 g/sq m; and the meshes from 20 x 20 to 1 x 1; As to the weave, it might be leno or plain.
Application
(1), In construction industry for wall finishing reinforcement. There are different specification adopted, such as 70-5x5, 80-5x5, 100-5x5, 130-5x5, 150-5x5, etc..
(2), In construction industry for reinforcing water proofing products, such as water proofing membrane, water proofing roof.
(3), In construction industry for reinforcing cement floor.
(4), In stone industry for reinforcing marble slabs, etc.. There are many different specification, which might be made according to customers demand.
(5), In stone industry for reinforcing mosaic. The specification and structure might be made at special demand for being suitable.
(6), In grinding wheel industry for reinforcing grinding wheel, cutting wheel, dish wheel, etc.. There are many different specification and different types made according to order.
(7), In many other fields as reinforcement for lots of application.
The main models of fiberglass net are as follows:
70-20x10
70-6x5
80- 6x5
100 - 5x5
130- 5x5
145- 5x5
160 - 5x5
As to the width and roll length, it might be according to order.
These sleevings are widely used as a wiring insulator for H-grade electrical machinery, electrical appliances, electric apparatus, and also for the protection of collected strands of wire.
(2) Silicone Rubber Fiberglass Sleeve
This sleeving possesses good qualities of dielectric, high temperature resistance, excellent elasticity. It can be used for wiring insulation and mechanical protection for electrical machinery and electrical appliances.
We offer many kinds of fiberglass silicone sleeve with good quality.
1245 Fiberglass Suppliers
Short on time? Let Fiberglass sellers contact you.
