Sucker Rod Wrench is made of high-quality alloy steel, and boasts and advantages of hardness and abrasion resistance. Its opening is applicable to the square shape of the steel-made sucker rod. The balanced design of wrench can reduce the fatigue of users, which is an outstanding tool for manual mounting and demounting sucker rod.
Made of AISI4145H alloy steel, drill collar mainly used between the dill pipe and drill head and connected by conversion connector so that they can provide the pressure and weighting to dill head ,in order to make the dill head to keep right trace .
If order of inquiry please offer: Non magnetic drill collar
outer diameter of dill collar
handling features
length of drill collar
stress relief features
drill collar bore
connection type
1. About the Manual
The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over).
2. ADVANTAGES OF DOWNHOLE MOTOR
Increased rate of penetration.
Better hole deviation control.
Reduction in drill string failure rate.
Reduction in wear and tear of the swivel, Kelly, and rotary drives.
Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor.
3. CONSTITUTION
Downhole motors differ in size and performance characteristics, but they share the same basic components as follows (Fig.1) :
Crossover Sub
Safety Catch Sub
Power Section
Coupling Assembly
Bearing Assembly
Mud motor, Downhole Motor used for HDD machine Rock conditation Drilling, Rock tools
ZQ series of drill pipe power tong marked with III are developed types from ZQ203-100 power tong. The power tong can be fixed on the accommodation track for front and back walk. It can pass across the well head and go to the mouse hole for working. Master tong can move upward and downward. Walk and lift of the tong can be remote controlled and automatically handled. Especially suitable for the occation with small wellbay suface.
All products will be made according to API and related international standards as per customers' requirements.
Integral blade stabilizer is an important tool in drilling engineering to control the well deviation. It can stabilize the drilling tools in the drilling process of oil, gas and geological exploration. It can increase the bit life, drilling speed and well bore quality. There are two kinds of integral stabilizers: spiral integral blade stabilizer and straight integral blade stabilizer.
Hardfacing type: HF1000, HF2000, HF3000, HF4000
3455 Drilling Machines Tools Suppliers
Short on time? Let Drilling Machines Tools sellers contact you.
We are a reputed name in this industry as a exporter of drilling casing in beijing, china.
Description & specification:-
Size: 4-1/2-13-3/8
Grade: j55, k55, n80, l80, c90, t95, p110, v150
Thread type: stc, ltc, btc
Length: r1, r2, r3
Standard: api spec 5ct/iso 11960
Technical Parameter
Model: 500A
Max. drill depth: 400m
Drill diameter: 110-450mm
Working air pressure:1.05-3.45Mpa
Air consumption:16-85 m3/min
Drill rod length: 3m
Drill rod diameter: 89mm;108mm; 114mm;140mm;
Reverse drill rod: 108mm,127mm
Axial pressure: 5t
Lifting force: 20t
Slow lifting speed: 4.2m/min
Slow feed speed: 5.2m/min
Fast lifting speed: 30m/min
Fast feed speed: 37m/min
Rotation torque: 8500Nm;4250Nm
Rotation speed:0-90r/min;0-180r/min
High landing leg travel distance:1400mm -Optional
Penetration rate:10-25m/h-Down hole drilling with hammer
Travel speed:2.5Km/h
Weight:11.5 t
Whole dimension:6.5x2.1x2.8m
Application formation: Unconsolidated layer or bedding rock
Application: Water well or Pilling engineering
Drill method: Mud or downhole hammer drilling
Hammer: Intermediate or high air pressure series
BOP Testing Unit, also called pressure test pump which is recommended for high pressure testing of BOP stacks, choke and kill lines, Christmas trees and any other type of equipment requiring high pressure static testing. Test Units are available in unit-mounted, portable, skid-mounted and high flow electric driven styles. Accessories include stand-mounted chart recorders and high pressure hose assemblies. High Pressure Test Units are provided in working pressure ranges from 5,000 to 20,000 PSI.
Accessories of pressure test unit, including stand-mounted chart recorders and high pressure BOP Accumulator Units, meet the design specification specified in API 16D. Customized pressure test pump is available to assure reliable control of the BOP stack with adequate reserve for continuous operation under emergency conditions.
BOP Testing Unit
Running stability, small size, light weight, low noise, easy maintenance and high efficiency.
Can be controlled locally and remotely, and monitor, record, print and track the recording value.
Can be used both in factory and in the field installed on a vehicle.
In accordance with API 16D.
Three type of pump: Electric, Pneumatic and Electro-Pneumatic.
Accumulator unit for BOP stacks is a very important equipment which controls BOP stacks and gate valves controlled by hydraulic pressure especially in drilling and workover operations. It is necessary to accurately operate and maintain the hydraulic control system. It consists of remote control system, drillerâ??s panel, air cable (except electrical type), pipe rack (electrical warming system available for cold area), high pressure manifold, protection room, etc.
It can be divided into two types: Electrical type FKDQ series and Pneumatic type FKQ series.
blowout preventer accumulator unit, blowout preventer accumulator unit, blowout preventer accumulator unit, blowout preventer accumulator unit, blowout preventer accumulator unit, blowout preventer accumulator unit, blowout preventer accumulator unit, blowout preventer accumulator unit, blowout preventer accumulator unit, blowout preventer accumulator unit.
Complete diverter controls with sequencing options and indicators.
Alarm systems to alert operator of potential issues and if drilling operations should stop to prevent a possible uncontrolled well situation.
Components have been field tested for decades to ensure dependability, maximum life and minimal downtime service.
It work with most PLC manufacturersâ?? control equipment to be compatible with your rig electronics.
It can be designed and manufactured to any specification including ATEX, all European Directives, GOST, NORSOK, DNV, ABS and all major oil companies specifications.
drilling spool and adapter can be designed according to customer's all kinds of models and sizes to meet the requirements in work site.
There are three kinds of connecting models for BOP connection and outlets, including flanged, studded and clamped-in style.
Gasket groove is line welded by stainless according to API Spec 6A, so as to prolong the using period and decrease the maintaining cost.
F1600 pump unit is used for transporting high viscosity, large proportion, higher sediment concentration
Drilling fluid to the well bottom in high pressure, for cooling the bit, wash the bottom, break the rock, and
Carry out rock cutting when return from the well bottom. It is one the main process equipment of oil drilling
Operation.
F1600 electric pump unit is consist of mud pump, dc motor, small base, big base, belt transmission system, spray system, pressure relief manifold and charging system etc. Dc motor is installed on independent skid, and fixed integrally on the big base behind the f1600 pump. Motor power is transmitted to mud pump from input shaft by belt, then drive the mud pump. Small base is equipped with a regulating screw, which can adjust the elasticity of belt. The matching electric spray pump is used to cool hydraulic end piston, cylinder liner, thus to make sure they work properly.
Api standard
F1600 pump unit meets the requirements of api 7k drilling and wellhead equipment
Operation specifications and sy/ t5138 standards.
Lake reverse circulation junk basket (rcjb) is designed to remove all types of small junk objects from the hole. The tools main feature eliminates pulling a wet string. Even when the tool is fitted with a magnet insert, reverse circulation is maintained.
Operation:
Lake reverse circulation junk basket is made up to the bottom of the fishing string and lowered to a point within several feet from the bottom of the hole. Begin circulation to wash the hole. Stop circulation and drop the steel ball. (when the steel ball is dropped into the valve seat, circulation fluid travels outward and downward through the inner passage of the barrel and out through the vents in the lower end. The fluid is then deflected to the center of the tool and up through the return holes in the upper end of the barrel. This reverse fluid circulation carries the junk into the barrel above the junk catcher.) begin circulation again, slowly rotating while lowering the tool until a 10â?? core has been cut. Stop rotation and circulation and pull the tool from the hole
API 6A Standard spacer spool and drilling spool
1. Standard: API
2. Pressure:2000PSI-20000PSI
3. Size: 3 1/8"--26 3/4"
Spacer spool, in accordance with API 6A, have end connectors of the same size, rated working pressure and design. Spacer spool is wellhead sections which have no provision for suspension of tubular members and which may have no provision for sealing of tubular members
We manufacture the spacer spool in all sizes and pressure ratings suitable for Well Head extension, B.O.P. spacing, and Choke, Kill, and Production Manifold applications. spacer spool usually has the same nominal end connections. spacer spool identification consists of naming each end connection and the overall length (outside of end connection face to outside of end connection face).
We can produce all kinds of API 6A double studded adapter for wellhead use. It is the important device to connection the defferent flange for wellhead, so the material of the body and studs and nuts shall be conforms the related requirements. The size is in accordance with API flange certification.
Our company developes the coarse alloy suitable for earth drilling and drilling tools used in building which has a a good impact toughness, longer life. The production scale of the company allows us to guarantee product quality while providing more competitive prices.
The grades of our Carbide products almost cover all the grades mentioned in the ISO. All of them match or even exceed the standard of the ISO, for the application of the up-to-date technology HIP-sintering and Hot Process technologies, which can make the properties of our carbide products reach up to A00,B00,C00.
All the products of the company are guaranteed with ISO9002 Quality System ,and ensures by the internationally advanced low voltage sinter technic and full developed hotprocess craftwork ,its hard alloy products are high grade articles that clients best .
The HDD drill rod has four different specifications for customer's choice: 50, 60, 73 and 89. And the length of drill rods and connection threads can be made totally according to specific requirements of clients. The normal length of our HDD drill rods is 3m.
Regarding its packaging, slotted steel frameworks are utilized to pack HDD drill rods in the forms of bundle, and each bundle has 20 to 50 drill rods.
Features of HDD Drill Rods:
1.Pipe end upsetting technology, self connecting mode and heat treatment have been used in the manufacture of this kind of HDD drill rod. Thus, our drill rods in different specifications possess excellent mechanical properties.
2.Double-step structure is used for its male and female threads, so this kind of drill rod has optimal sealing property and after torsion, there is little transformation in the rod.
3.Chemical plating (electroless plating) is used on the surfaces of threads so as to improve the hardness of surface and abrasive resistance of thread.
4.Our HDD drill rods can work together with various horizontal directional drill rigs within and beyond China.
9 be used for water well, oil field, underground, construction, geothermal, directional boring
114-117, 127
Soft Formation Tooth Bits
The 114-117 bits are used to drill low-compressive strength, soft formation. Long projection tooth lengths are used on high offset cones to provide the greatest penetration rates possible. Wear-resistant hard facing is used to control tooth wear. On the softest bits type this hard facing completely covers the bit teeth.
127
Medium-Hard Formation Tooth Bits
The 127 bits are used to drill high-compressive strength, medium hard formations. Short projection teeth with reduced crest length are used in this series of bit designs. Durable hard facing is applied to reduce tooth wear.
437
Soft Formation TCI Tricone Bits
The 437 TCI bits are used to drill low compressive strength, very soft formations. TCI bits maximize the use of both conical and chisel tungsten carbide inserts of large diameters and high projection. This cutting structure design, combined with maximum cone offset, result in high bit penetratione rates. The deep intermesh of cutter rows prevents bit bailing in sticky formations.
517
Medium Formation TCI Tricone Bits
The 517 features aggressive chisel tungsten carbide insert on the heel rows and inter rows. This design provides a fast drilling rate and added cutting strcture durability in medium-to-medium hard for-mationes. The HSN rubber O-ring provides adequate sealing for bearing durability.
637
Hard Formation TCI Tricone Bits
The 637 bits can be used to drill hard and abrasive forma-tions. Wear-resistant tungsten carbide inserts are used in the outer rows to prevent loss of bit gauge. Maximum numbers of hemispherical-durability and long life.
617
Medium-Hard Formation TCI Tricone Bits
The 617 feature robust chisel tungsten carbide inserts on the heel row and conical on the inner rows. This design provides a fest drilling rate and added cutting structure durability in medium to medium hard formations. The HSN rubber O-rin provides adequate sealing for bearing durability.
3455 Drilling Machines Tools Suppliers
Short on time? Let Drilling Machines Tools sellers contact you.
