1. Application Ozone is rare in the atmosphere but a main factor for rubber crack. This product simulates and strengthens the ozone condition in the atmosphere, studies of the law of ozone reacting on rubber, and quickly identifies and evaluates the anti-ozone aging performance and the anti-ozone agent protection efficiency of rubber. Reference standard: GB/T7762-2003 vulcanized rubber or thermoplastic rubber ozone cracking resistance static tensile test, GB/T 2951.21-2008 cable insulation and sheath material general test method, GB/T 11206-2009 rubber aging surface cracking test method, and other relevant standard test methods. 2. Machine Platform Structure (1) Refrigeration System A, Adopt the completely closed original French Taikang compression head B, Scale type fan cooling condenser. C, Scale type multi stage automatic load capacity adjustment evaporator D, Environment-friendly frozen snow species E, Other accessories: desiccant, oil separator, high voltage protection switch F, Expansion system: all imported units from Europe and America are used. (2) Electronic system: (safety protection system) A, Zero crossing gate fluid power controller SSR 2 set; B, Compressor overheat protection switch. C, Compressor overcurrent protection switch; (3) Air duct system: adopt multi Wing Stainless Steel Zhu long to speed up hot and wet winding. (4) Heating system: scale type stainless steel electric heating tube. (5) Control system A, TEMI880 LED display, touch-type setting data, input in Chinese and English, programmable temperature regulation, humidity controller, touch-type setting data input can be programmed and manual control B, Degree of resolution: 0.01 C, Temperature range: 10 ~ 70 D, Each segment can be directly set temperature and time. (6) Inside and outside box insulation layer. A, Inner box material: SUS#304 1.0 mm thick stainless steel plate. B, Outer box material: SUS#304 1.2 mm thick stainless steel sand paint C, Thermal insulation material: PU rigid foam glass wool
Description: The test apparatus suitable for measuring the smoke emitted by wires and cables burning under specific conditions, such as horizontal combustion of some cables or optical cables, are used as a means of comparing different cables or optical cables or judging whether they meet specific requirements under flaming or flameless combustion conditions. . It meets the test standard of GB/T17651.1-2-19.98 "Determination of smoke density in combustion of cables and optical cables under specific conditions". Performance parameters: Optical measuring device: The light source and receiver should be placed in the middle position outside the sealing window on the opposite wall of the combustion chamber. Measurement range: 0-100%. That is, the optical device will be energized before the blank test. Calibration of transmittance: calibration with transmittance of 25%, 50% and 75%. Standard Fire Source: Standard Fire Source: 1.0L+0.01L Alcohol Plate; Ethanol: 90% +/- 1%; Methanol: 4% +/- 1%; water: 6% +/- 1%. Control system: adopt DETECION control procedure and ZWH 4500 acquisition control card. Operating interface: WINDOWSXP operating interface, DETECION control program, perfect security mechanism. During the test, the measurement results are displayed in real time and the perfect curve is plotted dynamically.
Constant Temperature Humidity Test Chamber 1. Criteria Performance indicators meet the requirements of GB5170, 2, 3, 5, 6-95 Basic parameters verification methods for environmental test equipment for electrical and electronic products low temperature, high temperature, constant humidity and alternating humidity and heat test equipment. Basic environmental test code for electrical and electronic products test A: low temperature test method GB 2423.1-89 (IEC68-2-1) Basic environmental test code for electrical and electronic products test B: high temperature test method GB 2423.2-89 (IEC68-2-2) Basic Environmental Test Rules for Electrical and Electronic Products Test Ca: Constant Humidity and Heat Test Method GB/T 2423.3-93 (IEC 68-2-3) Basic Environmental Test Rules for Electrical and Electronic Products Test Da: Alternating Humidity-Heat Test Method GB/T423.4-93 (IEC68-2-30) Control Methods and Characteristics Balanced temperature control system (BTHC) controls SSR by P.I.D. so that the heating and humidification of the system is equal to the loss of humidity and heat, so it can be used stably for a long time. 2. Refrigeration system 2.1 Compressor: fully packed compressor imported from France 2.2 Refrigerant: environmental friendly refrigerant R404A 2.3 Condenser: fin type heat sink motor 2.4 Evaporator: fin type multi-stage automatic load capacity adjustment 2.5 Other accessories: desiccant, refrigerant flow window, repair valve 2.6 Expansion system: capacity controlled refrigeration system 3. Main technical parameters Temperature range -40150 Temperature fluctuation ±0.5 Temperature deviation ±2 Heating time about 4 degrees /min (no load non-linearity) Cooling time about 1 degrees /min (no load non-linearity) Humidity range 20% ~ 98% R.H Humidity fluctuation 3% R.H Humidity deviation 3% 4. Structure and Material A. Inner box material: stainless steel plate (SUS #304 1.0 mm thick) B. Outer box material: stainless steel plate is atomized or baking varnish (SUS #304 1.0 mm thick). C. Insulation material: hard Polyurethane foam and glass wool. D. Air supply circulation system: (1) 90 W motor (2) stainless steel lengthened axle center (3) Multi leaf fan (SIRCCO FAN) E. Box door: single door, single window, left open, handle on the right hand side. (1) Window 270 x 360 x 40 mm 3-layer vacuum layer. (2) Planar embedded handle (3) Rear button: SUS #304
Liquid Thermal shock test chamber Three Zone Thermal Shock Test Chamber Thermal Shock Test Chamber Liquid Thermal Shock Test Chamber,Cold and hot impact machine can be used to test material structure or composite material, in an instant by extremely high temperature and extremely low temperature continuous environment can endure degree, in order to in the shortest time test commits any heat bilges cold shrink caused by the chemical changes or physical damage. Applicable objects including metal, plastic, rubber, electronics, pv, solar... And other materials, the products can be used as a basis of improving or reference. Significant reductions in fluid usage make liquid thermal shock affordable Purchasing a liquid thermal shock chamber needs close consideration of the long term operating costs. The specialized liquids used can easily evaporate, causing the loss of thousands of dollars of fluid per year, if not properly contained. Liquid-to-liquid thermal shock testing is typically conducted to apply very strong, repetitive thermal stress to test pieces. It can model a product's ability to withstand thermally-induced size changes, crack resistance, hermetic integrity, and changes in electrical properties. This form of testing provides a very rapid temperature shock recovery of conditions, and it can significantly reduce testing time by requiring shorter soaks and less cycles. The liquid thermal shock chambers have been built to meet the demanding test requirements, which has become a defacto industrial standard for semiconductor devices.
Tunnel oven/conveyor oven Precision Vacuum Oven Electrically heated tunnel oven GRANDE electric heated tunnel ovens are based on a mature and time-tested system with a 10 year proven record of reliable round the clock production.The design is flexible and energy efficient and is built for decades of continuous use.The ovens are suitable for variety of products,ranging from buns to bread,cakes,moon-cakes and pastries.The tunnel ovens are manufactured in two basic versions,depending on the desired temperature range:Normal temperature up to 250??(482�F�) or high temperature up to 500??(935�F�). Features & Benefits Energy saving technology GRANDE tunnel ovens are built with super insulating material that ensures that very limited heat escapes from the ovens resulting in the exterior being relatively cool.The exterior is made of stainless steel and our ovens are known throughout the world of their advance technology and energy efficiency. Heating The tunnel ovens are heated by the tube elements with double heating spirals.They are specially made for each oven to maximize the heat control and reliability of the elements.On average,we use 12 elements per meter of oven.The elements,placed on the top of the oven chamber and below the belt,are easily accessed from the side. Turbo Zone From some products,especially when baking with tins,the use of air circulation from turbo fans in combination with radiant heat is suitable.In such cases the oven is equipped with turbo zones.In a mesh belt oven,the hot air is forced through the belt and in a solid steel belt oven the hot air is blown horizontally along the zone.Turbo zones allow for the baking time to be reduced and lower temperatures used.With the adjustable fan speed the optimal turbo effect can be reached. Steam system In ovens equipped with a steam system the first part of the oven contains steam spread boxes made out of the highest grade of stainless steel.Valves with indicators are used to adjust the proper flow of steam. Oven Control System The PLC touchscreen is designed to be easy to use and give the best possible overview and control.Apart from temperature regulation and oven control,the touchscreen also comes standard with recipe handling,alarms,log function and Internet connectivity. Belt Driving System A frequency converter controls the speed of the driver motor,and the robust belt driving system provides optimal reliability and exact baking time.Long ovens and ovens for heavy products are fitted with double drive system,each with its own motor. Belt conveyor ovens The lowest cost and most common type of conveyor oven,belt conveyor ovens are extremely versatile and best suited for relatively light loads.In addition to standard wire mesh belts,Teflon coated fiberglass reinforced belts are also available for temperatures up to 500??(935�F�).These belts are non-marring and therefore well suited for handling coatings or finished products.
Temperature only test chamber/High and low temperature test chamber Temperature Only Test Chambers High And Low Temperature Test Chamber Temperature chamber models designed to save lab space The Temperature chamber series provides an economical and space-saving solution for a variety of temperature testing requirements. Lowest temperature: -20 or -70�C (-4 or -100�F) Highest temperature: 180�C (354�F) The extended temperature ranges of the Standard series make testing at extreme conditions possible without buying a larger, stand-alone chamber. Two chamber sizes are available, as well. The programmer includes a temperature alarm as just one part of Grande's three-tiered over-temperature protection system. A thermal fuse and a user-set independent limit are also included. In addition, a specimen power terminal allows the user to safely operate powered equipment inside or with the chamber. Features High performance and quiet operation (65 dBa) Space-saving footprint, designed for flush installation to wall Stainless steel exterior Full thermal break around doorframe One 50mm (2") or 100mm (4") diameter cable port on left, with flexible silicone plug Three levels of overheat protection, plus overcool protection Easy lift-off service panels, electrical access on left Detachable eight-foot power cord with plug ETL listed electrical panel conforming to UL 508A Touch-screen programmer/controller with Ethernet Save 120 profiles with up to 1200 steps each (ramp, soak, jump, auto-start, end) One event relay for external device control, plus specimen power interlock relay for safety Grande exclusive options include: Web Controller for full remote access; Chamber Connect software for basic data logging and monitoring. USB and RS-232 ports available, as well.
Dust resistance test chamber IP Dust Test Chamber Dust Resistance Test Chamber Wholesaler Applications Dust resistance test chamber is designed for sealing performance test and reliability test, widely used in electrical, electronics, automobile, motorcycle, LED and other products. It is suitable for the work ability test on the shell sealing performance, product in dust free settlement, in the environment without apparent air flow or with a strong blast air and a large amount of sand dust, and similar conditions. Specifications: Dust proof test machine 1. We are manufacturer, offer reasonable price for you. 2. Customization of non-standard models are available. 3. Major parts adopt imported brands. �Features: Temperature Range: environmental temperature + 5~50?? (Adjustable) Humidity Range: 45%~75% (Adjustable) Metal net standard nominal line diameter: 50mAirflow velocity in the chamber: 1.5m/s (adjustable range 0~4.99m/s) Environmental air pressure: 85Kpa~106Kpa Test dust: dry talcum powder, portland cement, smoke ash and etc. Line spacing between the standard: 32m, 75m and 250m (There are three Metal nets) Selecting dust concentration control instrument: get sample through the optical principle, show the dust concentration and automatic control powder quantity that entering into the Cabinet according to the concentration of the set: (needed cleaning compressed air source configuration, require the pressure: 1~3 kg/cm3) Power supply: 380V 3phases 50 Hz/60Hz Besides dust proof test machine, our business range also covers: � Thermal shock chamber, Temperature humidity chamber, Ramp rate temperature chamber, Walk-in climatic chamber, Solar radiation test chamber, Ozone test chamber, Salt spray chamber, Industrial hot air oven, Dustfree hot oven, Temperature humidity control cabinet, Rain spray test chamber, Automatic glue dispensing machine, Climate and vibration combined chamber, Burn-in aging test room, Steam aging test chamber, Ventilation aging chamber, Vibration tester, Drop tester, Tensile tester, etc. Grande Electronics is one of the largest ce certified dust test chamber manufacturers and suppliers in China and also known as one of the famous chamber brands. Our discount product is mainly featured by good performance and flexibility and low price. Welcome to order the customized and cheap chamber made in China with our factory.
Programmable Temperature and Humidity Test Chambers 3-Layers Temp Humi Test Chamber Temperature Humidity Test Chamber Temperature and Humidity Test Chambers provides an economical and space-saving solution for a variety of testing requirements. It can simulate different climatic conditions, such as heat-endurance, cold-endurance, dryness-endurance, and humidity-endurance, which defines the performance of material. By testing the product under different climatic conditions to see whether its performance can meet the intended requirements. It is widely applied in the industries of electron, electrical equipment, vehicle, metal, food, chemistry, building materials, luggage, adhesion tape, printing, packaging, and other product components and materials. The programmer includes a temperature alarm as just one part of Grande's Three-tiered over-temperature protection system. A thermal fuse and a user-set independent limit are also included. In addition, a specimen power terminal allows the user to safely operate powered equipment inside or with the chamber. Corresponding Standard of the Temperature and Humidity Test Chamber: 1.GB11158 high-temperature testing condition 2.GB10589-89 low-temperature testing condition 3.GB10592-89 high-low-temperature testing condition 4.GB/T10586-89 humidity testing condition 5.GB/T2423.1-2001 low-temperature testing condition 6.GB/T2423.2-2001 high-temperature testing condition 7.GB/T2423.3-93 humidity testing condition 8.GB/T2423.4-93 alternating temperature testing machine 9.GB/T2423.22-2001 temperature testing method 10.IEC60068-2-1.1990 low-temperature testing method 11.IEC60068-2-2.1974 high-temperature testing method 12.GJB150.3 high-temperature test 13.GJB150.4 low-temperture test 14.GJB150.9 humidity test Grande Expertise in Humidity Control Controlling humidity in a small environmental chamber can be especially challenging. Grande expertise in humidity control brings intelligent design that is carefully integrated into the Criterion chambers. The humidity subsystems are designed for reliability, convenience, and performance: An external steam generator allows expanded range and is easy to maintain. A separate de-humidification coil improves low humidity control and range. Wet-bulb humidity sensor is a �??primary measurement method�?? for accuracy. It is also economical, easy to maintain, and reliable because it has no risk of failure due to over-saturation. (Read why analog is preferred over digital.) Direct water supply connection is standard, with options for water filtering and recirculating water tank. Features High performance and quiet operation (65 dBa) Space-saving footprint, designed for flush installation to wall Stainless steel exterior
3-layers temp humi test chamber Programmable Temperature And Humidity Test Chamber Temperature Humidity Test Chamber It is applied to test the materials in heat-resistance, cold-resistance, dry-resistance, moisture-resistance. It is simple to operate and program easy to edit. It can show the set values and operative time. Applied to test the prodcuts quality, such as electronic, plastic products, electrical appliances, instruments, food, vehicles, metals, chemicals, building materials, aerospace, medical care and so on. The three-in-one design makes the equipment easy to operate and space-saving.Users can do different testings of high temperature,low temperature and costant temperature humidity condition in every single testing area. Every system is entirely independant of each other,adopts 3 sets of refrigeration systems,3 sets of humidifying systems and 3 sets of controlling systems,so as to ensure stable and accurate controlling,and povide a longer service life. Touch control & setting mode is totally controlled and locked up by automatic micro computer system with PID value automatic calculating ability. Corresponding Standard of the Temperature and Humidity Test Chamber: 1.GB11158 high-temperature testing condition 2.GB10589-89 low-temperature testing condition 3.GB10592-89 high-low-temperature testing condition 4.GB/T10586-89 humidity testing condition 5.GB/T2423.1-2001 low-temperature testing condition 6.GB/T2423.2-2001 high-temperature testing condition
Three Zone Thermal Shock Test chamber Thermal Shock Test Chamber Liquid Thermal Shock Test Chamber Programmable Three Zones Thermal Shock Test Chamber is applied to aviation, military, ships, electrical, electronics, instruments and meters; medical equipment; civilian nuclear energy; colleges and universities; research laboratories; commodity inspection, arbitration, and technical supervision departments; building materials ceramic; petroleum and chemical products, For high and low temperature impact test. Three Zone models have higher performance, three-zone capability, and larger heating/cooling performance that fully benefits from Eco-mode innovations.Equipped with original Japan made true-color touch screen controller with software of both English and Chinese version.It consists of 3 Zones:1,High temperature Zone;2,Low temperature Zone;3,Testing Zone.Adopts unique thermal-break-structure class heating & cooling storage method,then leads hot or cold air to testing zone for thermal shock tests.It can be adjusted shock temperature by switching the hot and cold air flow. High memory capacity,can set 120 programs and each program can be repeated for max 9999 times.Each step can be proceeded for max 999 hours and 59 minutes.It's able to communicated with computer via RS485 port,so as to control,edit and record 2 groups of dynamic nodes,easy to operate.Proceeding with thermal shock conditions,users can select either 2 Zone or 3 Zone test mode.All operations are controlled by PLC.Equipped with automatic circuit and alarm signal in case of emergency,machine will be shut down in urgent situation. New Eco-Mode is standard for all models. Eco-mode manages the pre-conditioning and modulates refrigeration systems to reduce energy usage. Savings of up to 50% over previous models is possible, or as much as $2,000 a year. Two Zone models are lower cost models with only two-zone capability, lower performance, and partial savings of Eco-modGrande�??s Exclusive Touch-Screen
Temp humidity and vibration test chamber Temp humidity and vibration compatible Chambers Vibration Test Chamber Industrial-quality chambers for combination testing with vibration systems For years Temp.humidity and vibration compatible Chambers have been the workhorses of the environmental test chamber industry. Originally created to meet military test standards, their flexible design has made them suitable for a wide variety of applications. Fast temperature changes of5 to 25C/m. are possible, even with significant loads. The chambers have a removable floor, allowing integration with vibration test systems. Custom designs are common, allowing configuration to meet your exact requirements. Special model can interface with both vertical and horizontal vibration systems In addition, the�touch-screen controller�makes running an Grande environmental test chamber a breeze. The full-color, touch-screen interface is remarkably easy to use and understand. The Touch Screen Controller�can be managed remotely via our new�Ethernet/LAN-based Web Controller, serial port, or GP-IB/Lab View. Nearly every Agree chamber we build is designed per the application. Here is a review of what is possible with a custom designed chamber from Grande. Feature Capacity: 63 L to 6000L Temperature Range: -70 to 180C Humidity Range: 10-99%RH Cooling rate: 2-3C/min (standard), 5C/min, 10C/min�, 20C/min as option� Vibration: maximum up to 5000kgf�, 100g
Temperature Cycling Test Chambers Fast change rates test chamber Temperature Cycle Test Chamber Fast change rates testing chamber is suitable for testing the changes of instruments,electrical,electronic products,machine�and�parts�under�the�rapid�temperature change�or�the�the�gradient�conditions, takes advantage of compact, modern scroll compressors to bring fast temperature cycling to small form factor. Temperature cycling rates from 5 to 20�C/min. are possible. Two different ultimate low temperatures are available: -40�C or -70�C. The faster cycle times can be used to meet more aggressive test methods that require thermal stress during transitions. Significant test time can be saved in completing tests, as well. To demonstrate performance, Grande uses the international standard IEC 60068 3-5 measured at the supply air. Temperature cycles are run from hot to cold extremes, and the middle 80% of the transition is timed to determine performance. Your actual cycling results will vary depending on methodology, including the start and end temperatures, and the amount of samples loaded. Features QUALITY CONSTRUCTION Stainless steel exterior and interior Rounded interior corners for easy cleaning Full thermal break around doorframe and door Rotating door latch is easy and secure Dual-layer insulation of fiberglass and expanded foam for thermal integrity One 2" (50mm) to One 4" (100mm) diameter cable port on the left, with an impervious, flexible silicone plug Easy lift-off service panels Pressure relief port to allow air volume changes due to rapid temperature changes Three levels of overheat protection FTF PROGRAMMER/CONTROLLER Popular PID controller with touch-screen operation Stores 120 different profiles�with up to 1200 steps each (ramp, soak, jump, auto-start, end) Step types include: ramp, soak, jump, auto-start, and end Ethernet interface for remote monitoring and operation RECOMMENDED OPTIONS Dry air purge, to compensate for quickly shrinking air during cooling, as well as to reduce risk of condensation. Product temperature control, allows feedback from a second sensor on the product. Ensures faster completion of transition steps.
High altitude low pressure simulation test chamber Altitude Chamber For Sale Altitude Test Chambers Temperature testing at altitudes up to 100,000 feet. Grande can provide custom-built chambers for simultaneous testing of temperature and low-pressure altitude conditions. Two common applications are: Testing of avionics or other aerospace equipment to simulate actual conditions it might experience. Simulation of high-altitude conditions like might be found in mountainous regions. NOTE: Altitude test chambers are custom systems, and differing requirements may significantly change the cost and utility requirements. Please let Grande know as much detail as possible about your anticipated testing specification/method, and we can provide you with a tailored system for your requirements. Features Temperature range from -70 to 200C Altitude range from ground to 100,000 feet Optional humidity control when altitude system is off Chamber interior size specified by customer Automatic altitude control, integrated with temperature controller No manual setting of altitude level! Vacuum pump sized for climb/dive rate required by application Viewing window and cable ports available
Salt corrosion spray test chamber Configured for your specific tests Alternate Salt Corrosion Spray Test Chamber Grande makes rain and spray testing easier by offering a standard chamber capable of published and OEM proprietary test methods. The standardized design can be configured for the rain/spray tests you need, eliminating the guesswork in buying a chamber. The system is based on the specification requirements, and can also accomplish individual automakers tests, as well as electrical-enclosure tests. Our Design Grande's modular design allows you to add on additional features, depending on the number and type of tests required. One possible choice is to integrate the spray system with a regular temperature and humidity chamber to save money and floor space, while also creating an opportunity to simulate actual operating conditions your product may experience. Our system uses multiple control solenoids to vary the water's spray volume/pressure. A holding tank prepares the water to the desired temperature, if required. A pump ensures the water is delivered in the proper pressure range. The water is fed to a motorized manifold that rotates the spray arms. Each spray arm has an adjustable valve to allow finer control of the spray. Testing capabilities The specification is modeled after and doesnt differ greatly. Details about the nozzle types and the rotating nature of the spray arms and product table are also included in the requirements. Additionally, drip and car wash tests are also specified. Heavy splash/shower S1 Spray room temperature water with 40 nozzles at 14.2 psi (1 kgf/cm2) for 30 minutes. The flow rate of the water shall be 6.5 gallons/min. (24.5 L/m). S2 Spray room temperature water with 40 nozzles at 42.7 psi (3 kgf/cm2) for 60 minutes. The flow rate of the water shall be 10.3 gallons/min. (39.2 L/m). Light spray/rain R1 Spray room temperature water with two nozzles at 4.3 psi (0.3 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.8 gallons/min. (3.2 L/m). R2 Spray room temperature water with two nozzles at 1.4 psi (0.1 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.5 gallons/min. (1.9 L/m). Examples of OEM automotive manufacturers' requirements Heat the sample to a temperature above boiling, then spray with cold water for about two minutes. Repeat cycle. Heat the sample to boiling temperature, then spray with room temperature water for about fifteen minutes. Repeat cycle. Simulate a car wash by using high pressure spray. Features Rotating rain and spray nozzles designed to JIS specifications Speed control for the rotating spray nozzles Stationary product shelf - A rotating shelf is optional: see options Water pressure regulators, gauges and flow meters Special high-volume floor drain system to rapidly drain water out of the chamber Interior chamber size is the smallest possible area using the JIS specified nozzles Applicable Test Methods
HAST PCT high-low temperature test chamber with pressure high pressure accelerated aging testing chamber factory�High Accelerated Stress Test Steam Aging Test Chamber Ozone Aging Chamber Chamber/HAST Chamber It test the resistance to pressure and air tightness for circuit board, multi-layer circuit board, IC, LCD and magnet iron. This machine is one of the common machine in aging equipment, used to test various types of materials for their performance under the condition of high temperature and high pressure. Application: Quality inspection for all types of electronic products, electric appliance, and products from communication, instrument, metal, plastic, automobile, food, chemical, building materials, medical and aerospace industries. Pressure Accelerated Aging Test Chamber (HAST) Safety�Device high pressure accelerated aging testing chamber factory:�� �1.�Safety�device�for�the�pot:�If�the�inner�box�is�not�closed�,�the�machine�can�not�start �2.�Safety�Valve:�When�the�inner�box's�pressure�higher�than�the�machine's�undertake�value,�it�will�self-relieve. �3.�Double�overheat�protection�device:�When�inner�box's�temperature�is�too�high,�it�will�alarm,�and�Automatic�cut�off� the�heating�power. 4.�Cover�protection:�The�inner�box's�cover�is�made�of�aluminum�alloy,�can�protect�the�worker�from�scald.
Alternate salt corrosion spray test chamber Salt Corrosion Spray Test Chamber Salt Spray Test Chamber Configured for your specific tests Alternate salt corrosion spray test chamber adds below functions from traditional salt corrosion spray test chamber:Programmable controllers,accelerated test for copper and acid test.,etc.It complies with Standard of ASTMDIN IEC GJB. Grande makes rain and spray testing easier by offering a standard chamber capable of published and OEM proprietary test methods. The standardized design can be configured for the rain/spray tests you need, eliminating the guesswork in buying a chamber. The system is based on the specification requirements, and can also accomplish individual automakers tests, as well as electrical-enclosure tests. Our Design Grande's modular design allows you to add on additional features, depending on the number and type of tests required. One possible choice is to integrate the spray system with a regular temperature and humidity chamber to save money and floor space, while also creating an opportunity to simulate actual operating conditions your product may experience. Our system uses multiple control solenoids to vary the water's spray volume/pressure. A holding tank prepares the water to the desired temperature, if required. A pump ensures the water is delivered in the proper pressure range. The water is fed to a motorized manifold that rotates the spray arms. Each spray arm has an adjustable valve to allow finer control of the spray. Testing capabilities The specification is modeled after and doesn�??t differ greatly. Details about the nozzle types and the rotating nature of the spray arms and product table are also included in the requirements. Additionally, drip and car wash tests are also specified. Heavy splash/shower S1 Spray room temperature water with 40 nozzles at 14.2 psi (1 kgf/cm2) for 30 minutes. The flow rate of the water shall be 6.5 gallons/min. (24.5 L/m). S2 Spray room temperature water with 40 nozzles at 42.7 psi (3 kgf/cm2) for 60 minutes. The flow rate of the water shall be 10.3 gallons/min. (39.2 L/m). Light spray/rain R1 Spray room temperature water with two nozzles at 4.3 psi (0.3 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.8 gallons/min. (3.2 L/m). R2 Spray room temperature water with two nozzles at 1.4 psi (0.1 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.5 gallons/min. (1.9 L/m). Examples of OEM automotive manufacturers' requirements Heat the sample to a temperature above boiling, then spray with cold water for about two minutes. Repeat cycle. Heat the sample to boiling temperature, then spray with room temperature water for about fifteen minutes. Repeat cycle. Simulate a car wash by using high pressure spray.
Xenon Water-Cooling Aging Test Chamber UV Aging Test Chamber Ozone Aging Chamber Xenon Water-Cooling Aging Test Chamber,is designed to simulate full sunlight spectrum to produce destructive effect on material. The chamber cansimulates the light, temperature, rainfall (spray) and condensing (humidity), ismainly used to test aging resistance of products or spare parts affected by natural environment, it tests the material aging-resistant performance in sunlight, rain, temperature and humidity, you canknow the products quality at a very short time, such as the depigmentation, transmissivity, gloss, peeling, hard, softening. Specifications: Xenon arctest chamber 1. We are manufacturer, offer best price for you. 2. Major parts adopt imported brands. 3. LCD touch screen controller, easy operation. 4. Free parts warranty for 12 months. Features: 1. Equipped with black-board temperature meter to adjust temperature inside the chamber. 2. Xenon lighting time control. 3. Spraying period control. 4. Water recycling. 5. Automatic constancy of water temperature (cooling of recycling water) 6. Spraying, lighting, temperature, humidity and rotating platform can be controlled separately. 7. Equipped with viewing window. 8. Water shortage / over-temperature alarm. 9. Equipped with irradiance meter to show current light intensity inside the chamber. 10.LCD Touch Screen Controller, programmable of temperature, moisture, sun and rain 11.Humidity: 50-98%RH 12.Temperature: RT to 80C(-20 to 80C as option) 13.Blackboard Temperature: 55-100C 14.Light Source: Xenon Lamp 15.Spray Nozzle: 2mm
4. Performance specifications 1. Temperature range: RT+40 -70 2. Humidity range: 90% RH 3. Temperature control accuracy: ± 3 *Note: The performance guarantee of item # 5 above requires testing at a distance of 1/6 of each wall surface in the testing area, and must be measured after stabilizing with temperature and humidity for 30 minutes 4. Equipment placement space: at least 207 two hundred and seven 201cm (W H D) 5. Power supply: AC220V 50HZ 5 System structure 1. Heating system: Scaled stainless steel electric heating tube 2. Humidification system: glass nozzle 3. Temperature sensing system: Made of stainless steel SUR304Pt100 4. Control system: The control system adopts a P.I.D controller, which controls temperature and humidity simultaneously a. Controller specification: Accuracy: Temperature ± 2.0 +1 digit, with upper and lower limit standby and alarm functions 5. Box material Inner box material: SUS # 304 mirror stainless steel plate Outer box material: SUS # 304 stainless steel plate
model Basic parameters DL-60 DL-90 DL-120 DL-160 DL-200 Dimensions inside the test chamber (Long �? wide �? High) 600*450*400mm 900*600*500mm 1200*1000*500mm 1600*1000* 500mm 2000*1200* 600mm Test chamber volume 108L 270L 600L 800L 1440L Volume of brine tank 15L 25L 40L 40L 40L Laboratory temperature NSS ACSS 35�±1â??ï¼?CASS 47�±1â?? Pressure barrel temperature: NSS ACSS 47�±1â??ï¼?CASS 63�±1â?? Brine temperature: 35â??�±1â?? Spray mode Ordinary type without suffix letter, economical type (M) continuous spray (A), programmable spray (B) Spray volume: 1.0ï½?2.0ml/80cm2/h(Different mist collectors need to be converted according to this ratio) Spray pressure 1.00+0.01kgf/cm2 source AC 220V 10A AC220V 10A AC220V 16A AC220V 16A AC220V 16A
2.Technical parameters: 1. Box size in the laboratory: DL-120LA W1200 * D1000 * H500 (mm), Approximate dimensions: 2300 * 1300 * 1400mm, 2 standard temperatures, Laboratory temperature: nss acss 35 ± 1 /pass 50 ± 1 Pressure bucket humidity: nss acss 47 ± 1 /pass 63 ± 1 , Salt water temperature: 35 ± 1 It can be heated without water, 3 volumes, Laboratory capacity: 800L Salt water tank capacity: 40L, 4 compressed air, Compressed air pressure: 1.00 ± 0.01kgf/c 5 spray volume: 1.0-2.0ml/80c /h, 6 spray mode: continuous spray, timed spray, programmable spray, intermittent spray, demisting in the box, 7. Power supply: AC220V 50Hz/20A, 8. Material: The entire PVC board is made, and the salt spray testing machine adopts advanced three-dimensional reinforcement technology internally, with a strong and solid structure that never deforms. 9. Water adding method: An automatic water adding system is adopted, which has the function of automatically replenishing the water level when the water level is insufficient, and the test is not interrupted. 10. Nozzle: Precision glass nozzle, salt spray testing machine used for 4000 hours to ensure no crystal blockage. 11. Protection system: Equipped with dual over temperature protection and insufficient water level warning to ensure safe use. 12. Temperature controller: digital display, PID control, high stability platinum temperature probe, error 0.3 13. Heating method: The laboratory adopts direct steam heating method, which increases the temperature quickly and shortens the standby time of the salt spray testing machine. 14. The spray tower is equipped with two conical dispersers, which have the functions of guiding fog, adjusting fog volume, and even fog falling. 15. The pressure bucket adopts Henry's law to heat and humidify, and provide the humidity required by the salt spray testing machine laboratory. 16. Opening method: Pneumatic automatic opening is adopted, The salt spray testing machine is one of the "three prevention" (humid heat, salt spray, mold) testing equipment for artificial climate environments. It is an important salt spray testing equipment for studying the adaptability and reliability of various environments in industries such as machinery, national defense, light industry, electronics, light industry electronics, and instruments. This salt spray testing machine can perform neutral salt spray tests in accordance with GB/T2423.17 "Basic Environmental Testing Regulations for Electronic and Electrical Products - Test Ka: Salt Spray Test Method", and can also perform acetate spray tests. This salt spray tester complies with CNS, ASTM, JIS and ISO standards. The salt spray test is to test the corrosion resistance of the products after coating, electroplating, Anodizing, anti-rust oil and other anti-corrosion treatments on the surfaces of various materials.
