Capacity: 30,000 ton/year~240,000 ton/year Automation: fully automatic Calcination system: using boiling furnace to calcine, adopting heat conductive oil furnace as heat source Fuel: coal, natural gas, heavy oil, diesel oil. Packaging Details: wooden case packing /20 'container / 40 'container.
The parameters of the gypsum board production line are as follows: 1) Production capacity: 2 million ~20 million square meter per year. 2) Final product variety: common paper-covered, plasterboard fire resistance, paper-covered plasterboard, water resistance paper-covered plasterboard. 3) Product specification: thickness from 7mm ~ 15mm, length from 2400mm ~ 3000mm, width from 1200mm ~1220mm 4) Product quality: in conformity with standard of P.R.C gb/t9775-2008 paper-covered plasterboard. Wooden case packing /20 'container / 40 'container.
gypsum powder machine The big sized gypsum stones are crushed into granules which are less than 25mm by the crusher. After storing and conveying, they will be conveyed into mill for grinding.Then they will be classified through a analytical engine. The qualified powder will be conveyed to the calciner for calcination, while the unqualified one will return to the mill for further grinding until it is qualified. The calcined gypsum powder (it¡¯s usually called Plaster of Paris) will be stored in the finished product silo for the preparation of plasterboard raw material or directly packing and transport to the customer;s site. There are two types of the gypsum powder productionline. One uses the direct burning calciner (it is usually used in the small capacity line, such as 20000 or 30000 tons per year), the other uses the fluidized bed furnace (it fits for all the capacity of the gypsum powder line. This style is very popular in the gypsum powder industry.). Use 40 feet container to transport.
The paper faced gypsum board production line is the professional equipment for producing the new decorated material. The principal working process are as follows: first, we take certain amount of hemihydrate gypsum powder, water and other additives, through the automatic measurement device and automatic conveying system, they will be conveyed into the mixer and changed into the gypsum slurry which will be scattered on continuous moving faced paper evenly. Second, at the same time, with the continuous moving and vibrating, the slurry will gradually diffuse and even scattered. Then the slurry will go into the forming machine and compound with the top and bottom faced paper. By the process of extruding and forming, the slurry will be encased by the faced paper and the continuous pulpous gypsum boards are formed. Third, In the forming line, the wet solid paper faced gypsum board will be gradually formed after the process of recondition, natural coagulating, automatic cutting, etc. The wet board will be arranged according to the programmed control system. With the help of rollers, belt conveyer and overturner, they will quickly enter into the dryer. Fourth, the board will be strictly controlled in the separate temperature zone of the dryer. After blowing into different thermal hot air, the moisture of the wet board will be evaporated. Because of the reaction of the starch, the board will be attached to the faced paper, and then the dry gypsum board will form and exit from the dryer. Moreover, after passing though overtuner and the folding device (the front side is inside) for the second time, the board will be cut into certain specification by saw. Finally, the finished gypsum board will be conveyed to the automatic sealing device and the stacker. After the stacking, the board will be transported to the finished products warehouse by the forklift. 40 feet container for transportation.
1. PVC film lamination machine Usage and Characteristics The lamination machine is used to paste the decorative film and boards together. First, put the board on the rollers. After the dust collection process, coat the glue on the boards, the glue will be qualitatived after conveying on the guide rollers. Then it will be combined with the film and enters into the recombination mechanism. After passing and cyclic rolling of the two lines of press roller, pinch roller and forming roller, the recombination is finished. The machine is fit for the surface decorative materials, such as pasted and compound decorative film and decorative paper, etc of the PVC baseboard, profile, low foaming board and wood board, etc. Specification: Max lamination width: 1300mm Max lamination speed:2-15m/min The thickness of the laminated board: 2-50mm Transmit power: 4.50kw Power: 380V,50HZ(can be made according to the inquiry) Size: 12600*1950*1600. 2. aluminum film lamination machine Usage and Characteristics The lamination machine is used to paste the decorative film and boards together. First, put the board on the rollers. After the dust collection process, coat the glue on the boards, the glue will be qualitatived after conveying on the guide rollers. Then it will be combined with the film and enters into the recombination mechanism. After passing and cyclic rolling of the two lines of press roller, pinch roller and forming roller, the recombination is finished. The machine is fit for the surface decorative materials, such as pasted and compound decorative film and decorative paper, etc of the PVC baseboard, profile, low foaming board and wood board, etc. Specification: Max lamination width: 1300mm Max lamination speed:2-15m/min The thickness of the laminated board: 2-50mm Transmit power: 4.50kw Power: 380V,50HZ(can be made according to the inquiry) Size: 12600*1950*1600. It uses 40 feet containers to transport.
Gypsum powder equipment is composed of elevating system, dust collecting system, conveyor system, heat supply system, milling system etc.. And the heat supply system is the key link of the whole gypsum powder production line. The gypsum produced by our company has the following characteristics: 1.The equipment has small volume but large yield. 2.The equipment with easy structure can not be damaged easily. 3.The compact equipment covers less area. 4.It has comparative less energy consumption. 5.It can be conveniently operated and easily controlled. 6.The products are of good quality and gypsum of Paris is of ideal components and stable physical properties. 7.The capital construction investment is small and operating expense is low. Container.
Gypsum board production line. High quality, best price.
Fragmentizer large gypsum ore broken into less than 25mm of small particles through storage and transport into the mill for grinding, grinding, after an analysis machine to achieve the required fineness of the gypsum product starch into boiling furnace to calcine, the rest of the mill for further grinding until the return pass. Calcined gypsum powder sent to guessed eligible deposit or into storage products workshop .
Model : SC-60 Plate size L*W (mm) : 510*350 Max traveling speed (m / min) : 20-25 Limited grade ability : 20 Frequency (rpm) : 5600 Impact force (KN) : 10 Engine model : S20 5.0HP Starting system : Recoil starter Packing size (L*W*H) mm : 790*400*640 Net weight (KG) : 60. 790*400*640mm, 60KG.
1 Output: Standard brick 240-115-53mm 5760/h Hollow brick 390-190-190mm 900/h Multihole brick 240-115-90mm 3240/h 2 ISO9001 3 semi-automatic brick machine 4Hydraulic, easy operation 5 Place of origin: China 6Maximum pressure: 10tons 7 models: JF-QT1500D 8 Size of bamboo pallet 1100-570-20mm 9Overall dimension 3970-1830-2350mm 10installed capacity 24.2kw 11use ground area at least 3000 square meters 12Amplitude 15mm 13produce time 8 seconds 14Frequency of shock 6500time/minute.
Dimension L x W x H 4,600 x 1,800 x 1,300 (mm) Production Capacity 5 - 8 (tons / hr ) (Adjustable by frequency converter) Degree of Vacuum ¡Ü - 0.092 (Mpa) Augers Nominal Diameter ¡é400 / ¡é300 (mm) Extruding Pressure 3.0 (mpa) (Main / Vacuum Pump) Motor Power 37 / 5.5 (kw) Weight ¡Ö 6000 (kg) Features of Type TL-CXJ-300B 1. Leading technology specially made for high-grade extruded wet-forming ceramic tiles and bricks, especially for making the split tiles, roofing tiles, special shaped tiles and clay bricks etc. 2. Casting-steel-structured machine body, high strength gear-box, special alloy steel augers etc., to ensure high quality and reliable of production. Wooden frame bottom support.
Dimension L x W x H 2,838 x 1,724 x 1,540 (mm) Working Frequency ¡Ý70 (times/min) (Adjustable) To Be Split Tiles Size L x W£º(~300) x (~200 ) (mm) (Adjustable) Main Power 1.9 (kw) Weight ¡Ö 1500 (kg) Features of Type TL- PZJ-AT The type TL- PZJ-AT of leading technology specially made for the high efficient and auto-splitting process, by which the wet-forming co-extruded double-piece split tiles being split to separated pieces of final split tiles in up to 70 times per minute working frequency and beyond 99.5% qualified rate. Wooden bottom frame.
The Clay Supply Machine consists of four parts: storing, driving, transporting and crushing. It is used with bulldozer to store clay and feed clay continuously.
This production line contains a series of machine such as dust collector, ebullience calciner, Heat-conducting oil boiler etc.If you want to know more detailed information ,please consult me freely. 2. The main composition of gypsum is dehydrate gypsum©vCaSO4.2H2O©w. However, the gypsum powder used in practical production (such as the gypsum powder for gypsum board, for mould, for plastering) is to dry and dewater the dehydrate gypsum, reduce the content of crystallization water in it, so the standard of crystallization of gypsum powder can meet the needs of all kinds of gypsum powder, because it can change into plaster of pairs. Plaster of pairs can re-integrate with water when it is applied into production, and it can be processed into new type building materials with a high intensity, such as gypsum board, gypsum block, etc. 3. Existing gypsum powder drying technologies the following: the heat, produced by the burning of medium in the stove, is transmitted to frying cauldron and pipe of circumgyrate stove, then gypsum powders are added, after mixture and drying through milling equipments, the finished product is transmitted to the store house. In this way, the quality of gypsum powder is cheesy, because the content of crystallization water is uneven.
Specification (with Electric motor drive): Rated Output 5m3 /h Max. Horizontal Conveying Distance 200m Suitable Mix Ratio(Cement/Sand) í_1:3~5 Water Cement Ratio
1.Good quality and competitive price 2.Durable and long service life 3.Nice shape and excellent performance 4.Save power and popular in overseas market 1.Utilze machinery and mould vibration ,make the block density and strongbest,it is better than only single vibration, because of the work desk is v wide , to make the vibration spread equably, down vibration utilize double hands vibration, two oil motor make two vibration case correlate. 2.Material vehicle mechanism utilize screw net, which make laying material equably , shorten the time of round trip for material vehicle ,Accordingly shorten the moulding cycle. 3.This series products is full-fledged , technique is advanced ,to produce all kinds of blocks , and their quality is good , is high (load bearing block can arrive 20Mpa), geometry dimension is exact so on virtues(dimension error make sure within 1.5mm) 4.Using advanced screw net to lay material , which can make the material kinds extensive(liking sand, stone chips , slag, coal gangue, coal cinder ,coal ash and some construction waster etc.)they are environmental machine compare with other block s machine. 5.This machine realized mechanical , electronic and liquid integration ,PLC computer control automatically , hydraulic drive, machine vibration and hydraulic press to make block moulding, computer monitoring and control every link , which can realize error lock automatically, error detection and capacity statistics. make the block density better , cement quality is more littler. 6.It can produce block all day whatever the south ,north, which is one block making plant that is cheap for invest , faster result , operate easily, maintenance handly. 7.Don't need change any accessory ,only need call the program so that can produce load and unload block; it can produce you need only change different mould. 8.Our block machines are based on the advanced abroad machine characteristic ,This machine virtues such as , structure is good , look beautiful , highly durable , maintain rate is low, degree for atuomationcis advanced, which utilize two oil cylinders.
Moving block machine(QT40-3A) detail introduce: 1.Moving Block Machine mould structure: we design the mould structure specially in order to change the mould easily,about the mould lifespan ,we use the newst heat treatment equipment to do carburization work , and make the mould more stronger . usually we could assure to use 100000 time ,in fact it could us more lomg time . 2.About the Moving Block Machine electricity motor ,in Mixer and host machine ,we will use Germany siemens motor, because this two part nearly working all time in working day ,so we could use high level hard wearing motor for this, and ther motor we will also use CE standard , 3.About the Moving Block Machine switches,we will select the France Schneider brand , it is could assure the working process smoothly . 4.The Moving Block Machine Control System ,Using computer control and man-machine interface. Electrical equipments apply the well-known brands from Japan and Germany, like Japan Mitsubishi. The Control Systems integrates the experience design in the actual production line of the past 20 years, combines with the international development trend, to meet the national conditions. This design can be mastered with the simple training, professional knowledge is unnecessary. And the powerful memory is used for the upgrade. 5.Moving Block Machine specification Forming machine main theoretical data Dimension of host machine:1800í-1400í-1100mm Control style: Electrical control system Forming style: Vibration with hydraulic Vibration force: 35.5KN Vibrator style: mould vibrate Host machine power: 5.2KW Forming hight: 40-250mm Moulding period: 25S Weight of host machine: 0.8T Size of pallet: No need pallet Voltage: 220/240/380/440V Block machine line area needed:Workshop 50 m2; Total area about 800m2 Worker arrangement:operate 1; Material loader 1; Total 2. Production capacity Size(L x W x H) Pcs /Mould Pcs / Hr 400X150X200 5 750 400X200X200 4 600 400X250X200 3 450 QT40-3A Block Machine is a small block machine. It works on cement surface and move automatically. It has the characteristic as: without pallets, saving time, using the vibration mode box, forming a short time, high density products and benefit for small block factory.Since putting into the market, good economic profits and social benefits have been achieved. Seaworthy packing.
Automatic block machine(QT4-15B) (1) Main technical parameters Dimension: 2440í-2000í-2600mm Host machine power: 27KW Moulding area: 400í-800mm Vibration force: 40KN Moulding period: 15-20S Capacity: 70.25KVA Pallet Size: 1010í-550í-20/25mm Mixer model: JS500 Total Weight: 7.6T Water Consumption: 5T/every day Voltage: 380V Theoretical workshop area : 150m2 , need about 6-7workers .the office,curing area and stacking area to arrange according your fact status. (2) Production capacity Size(LxWxH) Pcs/Mould Pcs/Hr Pcs/8Hr 400X100X200 8 1200-1920 9600-15360 400X150X200 6 900-14407200-11520 400X200X200 4 600-960 4800-7680 400X250X200 3 450-720 3600-5760 Paver:200X100X60 161920 15360 Paver:200X163X60 81200 9600. We have the right to improve some according the workmanship and technology developing fact. Seaworthy packing.
Automatic block machine(QT8-15) 1.QT8-15 Main technical parameters Dimension: 3000í-2200í-2950mm Moulding area: 800í-820mm Moulding period: 15-20S Pallet Size: 980í-900í-25mm Weight: 12.5T Voltage: 220/240/380/440V Host machine power: 34KW Vibration force: 60KN Capacity: 93.55KVA Mixer model: JS750 Water Consumption: 9T/day. 2.Production capacity Size LXWXH Pcs/Mould Pcs/8Hours 400X100X200mm 14 16800-23520 400X150X200mm 10 12000-16800 400X200X200mm 8 9600-13440 400X250X200mm 6 7200-10100 240X115X53mm 42 60480 Paver 200X100X60 28 33600 Paver 200X163X60 12 14400. 3.simple block machine line area workshop: 200m2 office: 100m2 Total area: 2000m2 4.Worker amount PLC Operator 1 Material loader 1 Forklift Driver 1 Feeding pallet 1 Maintainer 1 Transport wet block 2 Total 7. We have the right to improve some according the workmanship and technology developing fact. Seaworthy packing.
Clay brick making plant wear resistant metal spraying technology was applied to the screw, pug mill, axis of screw and seasoning, conditioning, quenching treatment make sure the body of extruder work in long life. The harden surface gear was adopted in reducer, clutch are a component with own patent, all the treatments make the machine life-saving , meanwhile the reasonable design, compact structure reduce the energy consumption , without any shaking during working, even the extruder can working normal without foundation bolts.
