Chinese Builders Hardware Construction Material Equipment Suppliers and Manufacturers

Door Handle - 4-60

Door Handle- 4-59

Door Handle - 4-58

Door Hinges-2

Door Hinges-1

Packaged container houses have advantages such as earthquake resistance, wind resistance, easy construction, energy conservation and environmental protection, and recyclability. They are widely used in construction sites, scenic accommodation, hotels and catering, and other fields. The packaging size for a single set is W2438mm * L5800mm * H700mm, and the installed size is W2438mm * L5800mm * H2896mm. Multiple unlimited combinations are possible. It is an ideal product for temporary office and accommodation on construction sites.

1. High temperature strength; 2. Resistant to corrosion in various atmospheres; 3. Excellent thermal shock stability; 4. Good thermal insulation; 5. The energy-saving effect is remarkable The operating temperature is below 1350C. Thermal insulation refractories are characterized by high porosity, generally 40%-85%; Low bulk density and low dry 1.5g/cm3: low thermal conductivity, generally less than 1.0W (m.K), it acts as the thermal insulation material of industrial kiln, can reduce the heat dissipation loss of the furnace, save energy, and can reduce the quality of the equipment under heat, the mechanical strength, wear resistance and slag erosion resistance of the thermal insulation refractory material is poor, and it is not suitable for the load-bearing structure of the kiln and direct contact with slag, charge, molten metal and other parts

Mullite bricks refer to high-alumina refractories with mullite as the main crystalline phase, and the general alumina content is between 65% ~ 75%. It is mainly used for hot blast furnace top, blast furnace body and bottom, glass melting furnace regenerator, ceramic sintering kiln, petroleum cracking system dead angle furnace lining, etc. Mullite bricks have high refractoriness, up to more than 1790 C, and have good thermal shock resistance. There are two types: sintered mullite bricks and fused mullite bricks. The crystallization of fused mullite is larger than that of sintered mullite, and the thermal shock resistance is better than that of sintered products. Aluminum content: 65-90% Standard brick size: 230*115*65mm Compressive strength at room temperature: 100-120MPa Good thermal shock resistance:

Performance characteristics: wear resistance, corrosion resistance, peeling resistance, low creep, good thermal shock stability, service life is 1.5 times that of ordinary products; Main uses: Mainly used in blast furnaces, hot blast furnaces, carbon roasting furnaces, carbon calciners, coke ovens, steel barrels, casting systems, boilers, cement kilns, glass kilns and various kiln lining and thermal equipment, etc., suitable for metallurgy, machinery, building materials, casting, ceramics, electric power, petroleum, chemical and other industries. Standard size:230*115*65mm First-class high-alumina bricks Al2O3 75% second-class high-alumina bricks Al2O3 60%~75% third-class high-alumina bricks Al2O3 48%~60%

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

HSS M35 5% Cobalt Centre Drill Bits

HSS M35 5% Cobalt Step Drill Bits Set, Amber FINISHED, 3PCS:4-12, 4-20-4-32MM

170PCS HSS TWIST DRILL BITS SET, 118 DEGREE, DIN338, BLACK FINISHED IN METAL BOX. 1.0-8.0MMX0.5, EACH 10PCS 8.5-10.0MMX0.5, EACH 5PCS.

HSS M35 Cobalt 5% Twist Drill Bits SET, 1.0-10.0X0.5MM, 135 SPLIT POINT, DIN338 STANDARD, Amber Finishing,rose Plastic Box Packing