LC1001 is the semi-flowing heat-resistant silicone adhesive sealant which is made of special silicone rubber material the addition of thermal powders. With excellent conductivity,V0 flame retardant grade, excellent temperature resistance, can be in the range of 60 ~ 280 Long-term use. As well as good adhesion, long term use will not fall off, will not produce Contact gap to reduce thermal conductivity, moisture-proof, anti-seismic, anti-corona, anti-leakage and aging .The properties are widely used for the adhesion and sealing of the electronic components with high thermal conductivity, which is a single part of the acetone oxime type, It can be cured silicone rubber and conforms to the requirements of ROHS REACH UL.
Typical Applications
High power LED lamps and lanterns, electrical power, microwave oven, electronic components and other industrial products of thermal conductive adhesive sealing, alternative thermal conductive silicone used in high-power electric module and radiator thermal conductivity between fixed filling adhesive, no card buckle screw, more reliable filling heat, simple process and lower cost.
Applying Process
1.Surface clean : Clean the surface of the adhesive object and remove the rust, dust and oil.
2.Sizing: Twist the cap of the hose, squeeze the gel into the clean surface, and make it natural.
3.Curing: Place the bonded or sealed parts in the air while them to solidify naturally. Curing is a process from surface to the internal, within 24 hours (at room temperature and 55% relative humidity) will cure the depth of the 2 ~ 4 mm, if the site location is deeper that completely curing time will be postpone, especially it is not easy to come into contact with air. if the temperature is low, cure time also will be postpone .Prior to further processing or wrapping the bonded parts, it is recommended that the user wait long enough to ensure that the adhesion and integrity of the adhesion are not affected.
For more , please kindly feel free to contact rita(at)szutd.com
Ferro Silicon is a universal heatblocker used to produce carbon and stainless steel This additive is used with other ferro alloys in the deoxidising process of steel and in the production of silicon itself It is also used in the production of cast iron as it can accelerate graphitisation Ferro Silicon replaces the need for ferro manganese spiegeleisen and calcium silicides in the manufacturing process
LCK-10 silicon pad is a high-performance insulating material substrate of Kapton membrane coating with silicone and has good thermal conductivity and anti-pierce.LCK-10 is designed For those ceramic insulator substitutes like beryllium oxide�??boron nitride and bauxite. As we know that ceramic insulators very expensive and easy broken,however,LCK-10 is hard To broke and the price of it is low.
Features & Benefits:
Heat emission, insulation , fire prevention, shock resistance.
Thermal impedance: 0.41-in2/w(50psi)
Breakdown voltage can reach at 7000V
Designed for the substitutes of the ceramic insulators
Typical Applications:
Heating power components; Automobile electronic heating module; Power module; Household appliances;
LCD thermal conductive silicon mud is short for thermal conductive mud and have good thermal conductivity and insulation. The shape likes plasticine, no flow, not be dried solid, no volatile, high and low temperature endurance, take it without adhere your hands ,high viscosity, use repeatedly, can be molded into a certain shape, easy to use. Filling between the electronic component to be cooled and the heat sink / case, contacting closely to reduce the thermal resistance, quickly and efficiently reducing the temperature of electronic components to extend the electronic component the life and improve its reliability. Because of its good filling and low price, they are widely used in LED lighting industry and also the best choice for thermal cooling of the lighting industry when selecting thermal conductive materials.
Features & Benefits:
High reliability, excellent chemical and mechanical stability
Easy to meet the requirements for thickness variation in product design
After forming is not deformed in a static use, no settlement
Thermal insulation, excellent resistance to aging
Meet the environmental requirements of ROHS and UL
Rubber sludge, plasticity, repeated use
Typical Applications:
LED 1.Integrated LED internal drive
2. Round cap screw-type LED lamp
Solar
Backlight module
LCD-TV/PDP
For more , please kindly feel free to contact rita(at)szutd.com
193 Silicon Sealants Suppliers
Short on time? Let Silicon Sealants sellers contact you.
LCK-10 silicon pad is a high-performance insulating material substrate of Kapton membrane coating with silicone and has good thermal conductivity and anti-pierce.LCK-10 is designed For those ceramic insulator substitutes like beryllium oxideã??boron nitride and bauxite. As we know that ceramic insulators very expensive and easy broken,however,LCK-10 is hard To broke and the price of it is low.
Features & Benefits:
Heat emission, insulation , fire prevention, shock resistance.
Thermal impedance: 0.41-in2/w(50psi)
Breakdown voltage can reach at 7000V
Designed for the substitutes of the ceramic insulators
Typical Applications:
Heating power components; Automobile electronic heating module; Power module; Household appliances;
Fineway can custom manufacture ceramics balls, rollers, full ceramic bearings
and hybrid bearings per customers request. We can do Grade 3 to Grade 100 ceramic balls. Please contact us today to get a quotation for your requirement.
Fineway offers high quality ultra fine silicon nitride powder, the average particle size ranges from submicron order to coarse grain powder. With the high Purity and α phase crystal content, our powder can be widely used in solar and ceramic structural applications.
Beverages
Cosmetics & Pharmaceuticals
Food
Industrial & General
Potential Functions:
Anti Caking Agent
Colourant
Defoamer
Potential Applications:
Cleaning Chemicals Non-Alcoholic Drinks Skin Care
Dairy Personal Care Snack Foods
Health Care Ready Meals Water Treatment
Paints Seasonings
The LCV series silicon cloth is a kind of cloth production which made based on fiberglass substrate through special processing. Because of its nice thermal conductivity, insulation and convenient assembly, it widely used in electronic appliances industry. When using, you should select different thickness of the thermal conductive silicon tape to cut according to the size of the fever interface and the height of the gap. Then putting the silicon tape in the gap between the fever interface and their components gap to play as a heat-conducting medium.
Features & Benefits:
Heat resistance, insulation, fire prevention, shock resistance
Typical Applications:
Heating power components
Automobile electronic heating module
Power module
Household appliances
Computer and peripherals, the filling and any place need heat dissipation between the heating element and the bottom plate.
High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material.
Benefits:
Cost-effective, high conductivity, low thermal resistance
Soft and flexible, reducing the interface thermal resistance
High electrical insulation to protect electronic devices
Natural sticky, easy application, reworkable
Meet ROHS and UL environmental requirements
Applications:
High thermal conductivity module
new energy vehicles
Microprocessors, memory chips and graphics processors
Network communication equipment
Car equipment, charger
High-speed hard disk drive
For more , please kindly feel free to contact rita(at)szutd.com
Ultra-high thermal conductive silicone sheet is a high-performance heat conducting interface material made of 100% imported materials for fillingthe air gaps between the heating device and the heat sink or metal base.Its softness and elasticity characteristics enable it to be used for coveringa very uneven surface. Heat is transferred from the separation device or the entire PCB to the metal casing or diffuser to improve heat dissipationand improve the efficiency of heating electronic components and service
Features & Benefits:
High thermal conductivity, low thermal resistance
Soft and flexible, reducing the interface thermal resistance
High electrical insulation to protect sensitive electronic devices
Natural sticky, easy assembly, re-workable
Meet ROHS and UL environmental requirements
Typical Applications:
CPU, memory module
Communication hardware equipment
High-speed hard disk drive
Automotive engine control module
Microprocessors, memory chips and graphics processors
Military electronic equipment
For more , please kindly feel free to contact rita(at)szutd.com
LCN is a kind of thermal conductive pad which do not contain silicone oil and do not volatilize and apply in optical instrument and those have sensitivity on silicone oil. There is silicone oil exuding from traditional thermal pad after heating, however, LCN absolutely solve this problem of silicone oil leakage. Whats more, the LCN series are especially fitting for filling no flat and high cumulative tolerance interface.
Features & Benefits:
No siloxane, no volatilization, no pollution
Soft and low hardness material, good for filling
High thermal conductive, low contact heat resistance
Electric insulator
Typical Applications:
The products you are afraid of being polluted by silicone oil
Optical precision equipment
Laptop and projector
Mobile and communication equipment, high speed large storage driver
Heat pipe assembly, control equipment of car engine Telecommunication hardware and equipment
High-end industrial control, and medical electronic area
The material is heat reinforced polymer, designed to meet the Thermal conductivity and reliability demand for the thermal conductivity of high application terminal. In addition, the heat sinks performance benefits a lot from the low heat resistance. And improve the microprocessor, DC - DC converter of memory module and the reliability of power module. The phase change characteristics: the material is solid in room temperature and installation is completely convenient, used between heatsink and devices. The material can be softened and flowing when the products reach phase-change temperature to fill the devices tiny irregular contact surface. Thus, the material has the ability to fill the gap between the devices and heat sink completely, make the phase change better than non-current elastomers or thermal graphite pad and get the performance of thermal conductive silicon grease. The material is nonconductive, however, as the material has endured the phase change at high temperature, may make the metal get to the metal, so the phase change interface material cannot
Features & Benefits:
Low heat resistance and low stress
Natural sticky, easy to use-no need to use glue
No radiator preheating
Flow but not silicon oil
Low volatility--less than 1%
Silicone Emulsion 60% is used in industrial applications such as in Rubber and plastics as release agents and lubricants, in Food trays and plastic serving dishes as release agents, in Car polishes and household cleaners to improve protection, resistance, gloss and spread ability and in Textile finishing to enhance feel, water repellency and reduce the need for ironing. Silicone Emulsion 60% is also used in Perlite, vermiculite and clay and other building materials to improve water repellency and protect against dampness. Itâ??s used in Printing and papermaking for lubrication and as an antistatic agent. Silicone Emulsion 60% used as a Release agent for industrial rubber tire plastics and casting materials; Rotary offset printing lubricant; Industrial waterproofing agent and release agent; Additives for maintenance products; Polishing agent for floors and furniture; And Leather maintenance products, etc.
Silicone Emulsion 60%
WC Code: 24-005-04
Sales Specification
Appearance: White Liquid
Odour: Characterictic
Solid content (%): 60.00 �± 2.0
pH Value: 8.0 �± 1.0
Density (g/cm3): 0.953 �± 0.02
Soluble in water: Miscible
Silicone Fluid is used mainly as an intermediate for the production of a wide variety of products in the chemicals and industries. Fluid is intended for use in a variety of medical applications including; lubricant for plastic or rubber devices and instruments, inert protective coating and water repellent film on the skin, and a hydrophobic surface on glass and ceramic substrates.
Silicone Fluid 350
Silicone Dioxide Amorphous is used as filler in rubber products paints animal feeds and insulation materials Its used in printing inks varnishes and in the production of cement and refractory material its used as a precursor in the production of glass and silicon Silicone Dioxide Amorphous is used in sand casting in the production electronic components and works as a component in defoamer Its also used as a sizing agent for the textile industry
Sales Specifications
Appearance White powder
SiO2996
Moisture 009
Loss on ignition 006
Fe2O3001
AI2O3016
Na ppm5
CI ppm5
Density gcm3265
pH7
Whiteness92
Packing
Defoamer
A defoamer or an anti-foaming agent is a chemical additive that reduces and hinders the formation of foam in industrial process liquids. The terms anti-foam agent and defoamer are often used interchangeably. Strictly speaking, defoamers eliminate existing foam and anti-foamers prevent the formation of further foam. Commonly used agents are insoluble oils, polydimethylsiloxanes and other silicones, certain alcohols, stearates and glycols. The additive is used to prevent formation of foam or is added to break a foam already formed.
The defoaming agent is resistant to high temperatures, light in color, has good water dispersibility, is not prone to fish eyes and shrinkage cavities, and has no oil slicks or demulsification. It is suitable for all types of coatings and emulsions, water-based resins, and adhesive systems.
193 Silicon Sealants Suppliers
Short on time? Let Silicon Sealants sellers contact you.
