We are an international trading company based in Toronto Canada with branch operations in China, Vietnam, and Korea. Our focus is on facilitating trading partnerships and creating enduring relationships. We have the following product in a safe warehouse for liquidation to best offer: 1. Aluminum ingot as prescribed in the Chinese National Standard of GB/T1196-2008 AL99.70, with aluminum content of no less than 99.7%, maximum 0.16% iron, maximum 0.13% silicon, and maximum 0.010% copper. 2. Aluminum bar 6063 as prescribed in the Chinese National Standard of GB/T 3191-1998, with minimum 0.2% and maximum 0.6% silicon, maximum 0.10% copper, minimum 0.45% and maximum 0.9% magnesium, maximum 0.10% zinc, maximum 0.10% manganese, maximum 0.10% titanium, maximum 0.10% chromium, maximum 0.35% iron. Other impurity elements no more than 0.05% each and 0.15% total. Remainder aluminum. We look forward to hearing from you.
Ultra-high thermal conductive silicone sheet is a high-performance heat conducting interface material made of 100% imported materials for fillingthe air gaps between the heating device and the heat sink or metal base.Its softness and elasticity characteristics enable it to be used for coveringa very uneven surface. Heat is transferred from the separation device or the entire PCB to the metal casing or diffuser to improve heat dissipationand improve the efficiency of heating electronic components and service Features & Benefits: High thermal conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect sensitive electronic devices Natural sticky, easy assembly, re-workable Meet ROHS and UL environmental requirements Typical Applications: CPU, memory module Communication hardware equipment High-speed hard disk drive Automotive engine control module Microprocessors, memory chips and graphics processors Military electronic equipment For more , please kindly feel free to contact
High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material. Benefits: Cost-effective, high conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect electronic devices Natural sticky, easy application, reworkable Meet ROHS and UL environmental requirements Applications: High thermal conductivity module new energy vehicles Microprocessors, memory chips and graphics processors Network communication equipment Car equipment, charger High-speed hard disk drive For more , please kindly feel free to contact
LGS300 graphite thermal pad is a new thermal interface material. It transfers heat along the two directions, shielding heat source and components meanwhile improving the performance of consumer electronics products. The thermal impedance of LGS is very small and can completely replace the high-performance thermal grease while avoiding the shortcoming of poor and dirty thermal grease process. LGS thermal conductivity is three-dimensional, that is not only it can transfer heat between the heat source and the radiator in the vertical direction, but also in the vertical direction, which ensures that it can quickly transfer heat out in vertical direction when the partial heat is high. Therefore, LGS thermal film is very suitable in the small space to efficiently transfer heat generated by heat source. Features & Benefits: Ultra-high thermal conductivity, easy to operate; Low thermal resistance Light weight Typical Applications: IC ; CPU; MOS; LED; Heat sink; LCD-TV; Laptop; Communication equipment; Wireless switch; DVD; Hand-held device; Camera/digital camera; Mobile phone For more , please kindly feel free to contact
LGS1500 is a synthetic graphite heat sink.LGS1500 has an unique grain orientation, lamellar structure can be well adapted to any surface, even heat conduction along the two directions. Plane thermal conductivity of up to 1900W/m-K. LGS1500 products while also the thickness of uniform heat to provide thermal isolation. Heat shielding and components while improving the performance of consumer electronics products. LGS1500 composite graphite sheet is a polyimide sintered novel film material with high thermal conductivity and excellent product design flexibility. Features & Benefits: 1.High thermal conductivity -flat heat conductivity can be up to1900W /m-K,40% lower thermal resistance than aluminum, 20% lower than copper 2.Ultra-light -than the same size aluminum to 30%lighter, 80%lighter than copper 3.Thin -thickness from 0.017 ï¼?0.025mm and 0.04mm 4.Temperature resistance-using temperature up to 400, the minimum can be lower than-40 5.Easy processing-can be made into different die sizes, shapes and thickness, can provide planar sheet die 6.Ease of use-graphite heat sink can be applied to any smooth flat and curved surfaces 7.Flexibility- easily with the metal, the insulating layer or double-sided adhesive made of plywood, increase design flexibility in the back with adhesive For more , please kindly feel free to contact
LCD thermal conductive silicon mud is short for thermal conductive mud and have good thermal conductivity and insulation. The shape likes plasticine, no flow, not be dried solid, no volatile, high and low temperature endurance, take it without adhere your hands ,high viscosity, use repeatedly, can be molded into a certain shape, easy to use. Filling between the electronic component to be cooled and the heat sink / case, contacting closely to reduce the thermal resistance, quickly and efficiently reducing the temperature of electronic components to extend the electronic component the life and improve its reliability. Because of its good filling and low price, they are widely used in LED lighting industry and also the best choice for thermal cooling of the lighting industry when selecting thermal conductive materials. Features & Benefits: High reliability, excellent chemical and mechanical stability Easy to meet the requirements for thickness variation in product design After forming is not deformed in a static use, no settlement Thermal insulation, excellent resistance to aging Meet the environmental requirements of ROHS and UL Rubber sludge, plasticity, repeated use Typical Applications: LED 1.Integrated LED internal drive 2. Round cap screw-type LED lamp Solar Backlight module LCD-TV/PDP For more , please kindly feel free to contact rita(at)szutd.com
The LCV series silicon cloth is a kind of cloth production which made based on fiberglass substrate through special processing. Because of its nice thermal conductivity, insulation and convenient assembly, it widely used in electronic appliances industry. When using, you should select different thickness of the thermal conductive silicon tape to cut according to the size of the fever interface and the height of the gap. Then putting the silicon tape in the gap between the fever interface and their components gap to play as a heat-conducting medium. Features & Benefits: Heat resistance, insulation, fire prevention, shock resistance Typical Applications: Heating power components Automobile electronic heating module Power module Household appliances Computer and peripherals, the filling and any place need heat dissipation between the heating element and the bottom plate.
The material is heat reinforced polymer, designed to meet the Thermal conductivity and reliability demand for the thermal conductivity of high application terminal. In addition, the heat sinks performance benefits a lot from the low heat resistance. And improve the microprocessor, DC - DC converter of memory module and the reliability of power module. The phase change characteristics: the material is solid in room temperature and installation is completely convenient, used between heatsink and devices. The material can be softened and flowing when the products reach phase-change temperature to fill the devices tiny irregular contact surface. Thus, the material has the ability to fill the gap between the devices and heat sink completely, make the phase change better than non-current elastomers or thermal graphite pad and get the performance of thermal conductive silicon grease. The material is nonconductive, however, as the material has endured the phase change at high temperature, may make the metal get to the metal, so the phase change interface material cannot Features & Benefits: Low heat resistance and low stress Natural sticky, easy to use-no need to use glue No radiator preheating Flow but not silicon oil Low volatility--less than 1%
LC1001 is the semi-flowing heat-resistant silicone adhesive sealant which is made of special silicone rubber material the addition of thermal powders. With excellent conductivity,V0 flame retardant grade, excellent temperature resistance, can be in the range of 60 ~ 280 Long-term use. As well as good adhesion, long term use will not fall off, will not produce Contact gap to reduce thermal conductivity, moisture-proof, anti-seismic, anti-corona, anti-leakage and aging .The properties are widely used for the adhesion and sealing of the electronic components with high thermal conductivity, which is a single part of the acetone oxime type, It can be cured silicone rubber and conforms to the requirements of ROHS REACH UL. Typical Applications High power LED lamps and lanterns, electrical power, microwave oven, electronic components and other industrial products of thermal conductive adhesive sealing, alternative thermal conductive silicone used in high-power electric module and radiator thermal conductivity between fixed filling adhesive, no card buckle screw, more reliable filling heat, simple process and lower cost. Applying Process 1.Surface clean : Clean the surface of the adhesive object and remove the rust, dust and oil. 2.Sizing: Twist the cap of the hose, squeeze the gel into the clean surface, and make it natural. 3.Curing: Place the bonded or sealed parts in the air while them to solidify naturally. Curing is a process from surface to the internal, within 24 hours (at room temperature and 55% relative humidity) will cure the depth of the 2 ~ 4 mm, if the site location is deeper that completely curing time will be postpone, especially it is not easy to come into contact with air. if the temperature is low, cure time also will be postpone .Prior to further processing or wrapping the bonded parts, it is recommended that the user wait long enough to ensure that the adhesion and integrity of the adhesion are not affected. For more , please kindly feel free to contact rita(at)szutd.com
LCK-10 silicon pad is a high-performance insulating material substrate of Kapton membrane coating with silicone and has good thermal conductivity and anti-pierce.LCK-10 is designed For those ceramic insulator substitutes like beryllium oxideã??boron nitride and bauxite. As we know that ceramic insulators very expensive and easy broken,however,LCK-10 is hard To broke and the price of it is low. Features & Benefits: Heat emission, insulation , fire prevention, shock resistance. Thermal impedance: 0.41-in2/w(50psi) Breakdown voltage can reach at 7000V Designed for the substitutes of the ceramic insulators Typical Applications: Heating power components; Automobile electronic heating module; Power module; Household appliances;
Used on screw insulation sleeve; Locked on transistor to avoid short circuit between the cooling fins of the crystal shell.
High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material. Benefits: Cost-effective, high conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect electronic devices Natural sticky, easy application, reworkable Meet ROHS and UL environmental requirements Applications: High thermal conductivity module new energy vehicles Microprocessors, memory chips and graphics processors Network communication equipment Car equipment, charger High-speed hard disk drive For more , please kindly feel free to contact rita(at)szutd.com
Ultra-high thermal conductive silicone sheet is a high-performance heat conducting interface material made of 100% imported materials for fillingthe air gaps between the heating device and the heat sink or metal base.Its softness and elasticity characteristics enable it to be used for coveringa very uneven surface. Heat is transferred from the separation device or the entire PCB to the metal casing or diffuser to improve heat dissipationand improve the efficiency of heating electronic components and service Features & Benefits: High thermal conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect sensitive electronic devices Natural sticky, easy assembly, re-workable Meet ROHS and UL environmental requirements Typical Applications: CPU, memory module Communication hardware equipment High-speed hard disk drive Automotive engine control module Microprocessors, memory chips and graphics processors Military electronic equipment For more , please kindly feel free to contact rita(at)szutd.com
LCG is a kind of thermal interface material which coating thermal conductive polymer on a layer of fiberglass. The stickiness of the material is slightly weakness for easy procession. And insulation and tear resistance are also better. Its stickiness and flexibility, even in extremely rough and very uneven surface, also can bring a good thermal filling effect. Features & Benefits: Fiberglass substrate, anti-puncture, shear and tear resistance Only the bottom with a sticky, slightly faint on the front, easy to install High-load, low-hardness gap filling material Strong electrical insulation Typical Applications: AC / DC power supply Car equipment / charger Between the motherboard and the chassis Drive control any heating element Uninterruptible power supply (UPS) Power semiconductor-TO packaging products
LCN is a kind of thermal conductive pad which do not contain silicone oil and do not volatilize and apply in optical instrument and those have sensitivity on silicone oil. There is silicone oil exuding from traditional thermal pad after heating, however, LCN absolutely solve this problem of silicone oil leakage. Whats more, the LCN series are especially fitting for filling no flat and high cumulative tolerance interface. Features & Benefits: No siloxane, no volatilization, no pollution Soft and low hardness material, good for filling High thermal conductive, low contact heat resistance Electric insulator Typical Applications: The products you are afraid of being polluted by silicone oil Optical precision equipment Laptop and projector Mobile and communication equipment, high speed large storage driver Heat pipe assembly, control equipment of car engine Telecommunication hardware and equipment High-end industrial control, and medical electronic area
LC120 thermal silicone pad is a very cost-effective general economic thermal gap filling gasket, soft with its own micro-stick, easy assembly. Under low compressing force to show good thermal conductivity and electrical insulation properties. Bedding on the gap between the heat device and the heat sink or the machine shell to extrude air to reach the full contact forming a continuous thermal conduction. Using heat sink or machine shell as a cooling device can effectively increase the cooling area to achieve a good cooling purposes. Features & Benefits: Low cost, high efficiency, cost-effective Replace the volatile pollution of the thermal grease Natural sticky, easy to install, can be reused Wide range of thickness, can fill any uneven size gap Electrical insulation Typical Applications: Communication equipment New energy vehicles / power batteries Computer Car equipment / charger Switching power supply PC server / workstation Flat-panel TV Optical drive / COMBO Security equipment Notebook computers Video equipment Any heating element and radiator Physical Properties: Test Item Test Method Unit LC120 Color Visual - Off white Thickness ASTM D374 mm 0.3~15.0 Hardness ASTM D2240 Shore 00 40±5~80±5 Specific Gravity ASTM D792 g/cm3 2.1 Tensile Strength ASTM D412 Mpa 0.34 Elongation ASTM D412 % 100 Tear Strength GBT 529-2008 KN/m 1.4 Breakdown Voltage ASTM D149 KV/mm â?¥10 Volume Resistivity ASTM D257 Ω·cm 8Ã?1012 Continuous Use Temp EN344 -40~150 Flame Rating UL 94 - V-0 Weight Loss @150240H % â?¤0.5% Dielectric Constant ASTM D150 @1MHz 5.41 Thermal Conductivity ASTM D5470 W/m·K 1.2 Standard sizeï¼?200mmÃ?400mmï¼?300mmÃ?400mmï¼?Customized size available; Coated with fiberglass/one side or double side adhesive/aluminum foil available
High quality Chromite Ore in lumps and Dead & Light Burned Magnesite from Pakistan. We can supply your desired quality and quantity out of our readily available stock. We can meet your short or long term demands at competitive prices and desired delivery schedules. Cr2O3 (Chromium Oxide) 42% to 52%. MgO (Magnesium Oxide) Dead Burned 93% to 95%. Light Burned 91% to 92%
We are factory manufacturing disposable take out containers. Please send us details and we will quote you price.
Jp54 BLCO D6 D2
I have 20mt of Newsprint offset Prime material available: - Width: 91.44cm - Diameter: 127cm - 29 rolls total - +/- 20mt - Stock available now PLease get back to me as soon as possible.
