Grey MgO Board Magnesium Oxide board MgO board is a factory-made, non-insulating sheathing board product. It can be used for a number of applications including wall and ceiling linings, fascias, soffits, tile backing and underlayment. It is made of magnesium oxide, a type of mineral cement, and is commonly called simply MgO (pronounced emm-gee-oh) due to its chemical composition of magnesium (chemical symbol Mg) and oxygen (chemical symbol O). Think of MgO as a type of sheathing board (sort of like drywall or cement board) but with much-improved characteristics such as fire resistance, weather ability, strength, resistance to mold, mildew, and so on. ItemSize Thickness weight Quantity/20GP(pallet packing) 11200*2000|2200|2300mm 3mm 10kg 2400pcs 21200*2000|2200|2300mm 6mm 17kg 1280pcs 31200*2000|2200|2300mm 8mm 23kg 960pcs 41200*2000|2200|2300mm 10mm 28kg 768pcs 51200*2000|2200|2300mm 12mm 34kg 640pcs Appilications for mgo boad: In many applications, MgO boards can be used in the same ways as gypsum and Portland cement sheathings. The substitution is not fully direct in terms of sheet thicknesses, fastening methods and joint treatments, but is very similar. This makes MgO board an easy product to use. The possible uses of MgO board are vast, and some of them include:Firewalls. Partitions.Structural sheathing for wood or metal stud walls.Shower stall tile backer board.Facings for structural panels engineered to use MgO as the facing.Shaft liners.Ceilings.Soffits.Fascia.Substrates for coatings and insulated systems (such as Direct-Applied Finish Systems, EIFS, and stucco).
Good Substitution of LCPP Paraffin PVC Plasticizer Plasticizer C02 Description C02 is specially used to replace GB standard chlorinated paraffin because paraffin has high viscosity, dense, low plasticity when used as plasticizer. It has obvious application advantage comparing with chlorinated paraffin. a. Good color, suitable for various of color or colorless down-stream products. b. High thermal stability, decomposition temperature is higher than same data of paraffin, resistance to processing, lighter smell. c. Good plasticizing efficiency, the plasticity is 1.5:1 compar ing with paraffin, replace s ame quantity chlorinated paraffin or 30% main plasticizer of paraffin. d. Good compatibility w it h PVC raw mat erial, 100% replace chlorinated paraffin. e. Competitiv e pric e, reduce production cost for down-stream enterprises. Applications 1. Passed SGS certificate compliance with EU RoHS, REACH, SVHC and BPA regulations. 2. Low Pt-Co, suitable for light color or colorless products. 3. Good stability, high plasticizing efficency, mix with main plasticizer not affect products quality. 4. Children toy products request eco-friendly plasticizer if necessary, B02 or F01 could replace 30-40% main plasticizer. Specification Pt-Co �300 Acid Value(mgKOH/g ) �0.30 Heating decrease volume(125 oC, 2 h) �0.50 Density g/ml(20 oC) 1.17-1.20 Viscosity(mm2/s) �200 Flash point(oC) >175 Price Delivery Port :Tianjin/Qingdao Packaging & Delivery Packing :200kg iron drum/20MT Flexibag/1MT IBC Drum Delivery Lead Time :within 10-20 days after receiving the deposit Supply Ability :20,000 ton/year
Low pt-co plasticizer special for medical gloves Plasticizer e01 Description E01 is kind of special plasticizer developed for medical gloves manufacturer which requests low viscosity plasticizer. Comparing to other plasticizers, our product is processed from food grade palm oil, it is eco-friendly plasticizer passed sgs certificate compliance with eu rohs, reach, svhc and bpa regulations. A. Viscosity obviously lower than same item of similar plastic Izer because some pvc products limit to use high viscosity additive B. Good stability, high plasticizing efficiency, combined with main plasticizer dotp, dinp or tbc will not affect finished product quality. C. Good compatibility with pv c raw materials, replace 30% main plasticizer. D. Competitive pric E, reduc es c omposite cost of gloves. Applications 1. Passed sgs certificate compliance with eu rohs, reach, svhc and bpa regulations. 2. Viscosity is 30 cst (40 ?), solve high viscosity limitation problem, not affects settlement behavior of paste resin. 3. High flash point >200 ?, compliance with processing requirements. 4. Good stability, high plasticizing efficency, mix with main plasticizer would not affect gloves quality. Specification Pt-co 60 Acid value(mgkoh/g ) 0.30 Heating decrease volume(125 oc, 2 h) 0.50 Density g/ml(20 oc) 1.00-1.05 Viscosity(mm2/s) 30 Flash point(oc) >200 Price Delivery port : tianjin/qingdao Packaging & delivery Packing :200kg iron drum/20mt flexibag/1mt ibc drum Delivery lead time : within 10-20 days after receiving the deposit Supply ability : 20, 000 ton/year
High Plasticity New Plasticizer Used for Plastic Flooring Plasticizer B02 Description Processed from food grade palm oil, B02 is eco-friendly plasticizer passed SGS certificate compliance with EU RoHS, REACH, SVHC and BPA regulations. a.Good color and low Pt-Co, suitable for various of PVC products manufacture, specially used in colorless and transparent PVC products. b.Good compatibility with PVC raw materials, replace 30% main plasticizer and more percentage could be achieved with main plasticizer DBP, DIBP. c.Normally used in winter due to the low freezing point. d.Good thermal stability, suit able for different PVC products manufacturers. e.Good plasticity, w orks better with main plasticizer such as DOP, DBP, DOTP, etc.. f.Cost effective, i t would be first choice on plasticizer for PVC products manufacturers on condition that ensure products quality. Usage widely used in PVC processing industry, special for plastic flooring, synthetic leathers, flex banner, etc.. Applications 1.Passed SGS certificate compliance with EU RoHS, REACH, SVHC and BPA regulations. 2.Low Pt-Co, suitable for light color or colorless products. 3.High flash point(>200ºC),satisfy processing requirements. 4.Good stability, high plasticizing efficency, mix with main plasticizer not affect products quality. 5.DOTP is main plasticizer in exported PVC floor, A03 could replace more than 50%. 6.Our product could be used in both base layer and medium layer of PVC floor. Specification Pt-Co 60 Acid Value(mgKOH/g ) 0.30 Heating decrease volume(125 oC,2 h) 0.50 Density g/ml(20 oC) 1.04-1.06 Viscosity(mm2/s) 50 Flash point(oC) >195 Price Delivery Port : Tianjin/Qingdao Packaging & Delivery Packing :200kg iron drum/20MT Flexibag/1MT IBC Drum Delivery Lead Time : within 10-20 days after receiving the deposit Supply Ability : 20,000 ton/year
PREPARATIONS The substrate, bolt and anchor holes must be clean, sound, dry and free of oil, grease, without laitance and loose particles. Prewet the bolt holes thoroughly, but no standing water in it. Before applying ITLS CA-007H absorbent substrates must be saturated thoroughly, but without standing water. MIXING Mix 3.2-4.4 liters of clean water with 25kg bag of ITLS CA-007H together. To add water based on the condition of stirring and keep stirring around 5 minutes until grouting well. APPLICATIONS Pour ITLS CA-007H mortar after mixing into the reserved cavities and recesses use the stick or bar to remove the air bubble, ensure that air entrapped into the grout is allowed to escape. Suggest to blend the grout by auto-mixer for better application. COVERAGE 25 Kg ITLS CA-007H when mixed with water will produce approx. 13.5 liters of Liquid Grouting Mortar. ITLS CA-007H suggest to be placed in thickness ranging from 10-15cm/layer.
DESCRIPTION Instant cement as material for leveling concrete floor which required high flatness level. With base elements of cement, selected sand, filler and additive all of which homogenously mixed. ADVANTAGES * Easy and ready to use, by water addition only. * Fast working * Practical and high adhesive power * Floor would be flat/ level in a second APPLICATION CA-010 is used as a floor screed material surface that canâ??t be exposed and should be covered with floor material, such as: ceramic, granite, carpet, parquet and other materials.
Various types of �ooring | Heavy construction equipment | Electrical lightings and �ttings Painting and wall decors | Bathroom and sanitary items | Tiles and Parquets Steel drums | HDPE pipes | Steel and Iron
PFC series hydraulic impact crusher has 45 degree feed chute with replaceable liners. The main frame can be opened by hydraulic device. Thick blow bars with locking tongue set into a replaceable backing bar seat. All curtain liners are interchangeable. Positive rotor lock to ensure the safety of persons who change the rotor. With the strengthening and toughening bear and replaceable backing bar seat, this crusher can be applied to the waste recycling materials processing. Final products are in a good product shape,the low proportion of conifer-like. Main Features 1). High reduction ratio and crushing efficiency; 2). No-board connection; The blow bar with high chrome (high chromed blow bar). 3). Impact plate with a special shape. 4). Crushed product with cubical shape. 5). Easy maintenance and reliable operation. 6). Discharge sizes can be adjusted. -
Quick details of lsaw Out diameter 325-1420mm (14â?³ -60â?³) Production process Jcoe Wall thickness 8-40mm Length 3-13m Standards Api 5l, astm a672, astm a53, sy/t5768 -2006, gb/t3091 -2008, gb/t9711 -1 Steel grades Q235, q345, l245, l290, a53, s235, s275, s355, gr.B/x42/x46/x56, a672 b60 cl22 Tpi Sgs, bv, moody, ccic can be arranged before shipment. Packing In bulk due to big sizes Surface treatment Anti-rust black painting, anti-corrosion treatment (fbe, 3pe, 2pe) Tpi ( third party inspection) Sgs, bv, moody, ccic Applications Liquid shipping like oil, water and fuel, building and constructions, chemical vegetation, power station, as well as foreign drill system.
Description CC-500 Dura-Shine is one component, aliphatic, UV resistant polyurethane based topcoat membrane. Product cures with the humidity and produces a transparent film and by this way it provides excellent adhesion over the entire surface. Feature Resistant to UV, exposed sunlight and chemicals When applied, it forms as seamless membrane without joints Product keeps its mechanical features over a temperature span of 40 to 90 degrees Celsius Use Area Roof terraces balconies and verandas Industrial floor coatings Stadium, car parks Stones, marble and ceramic surfaces Coverage Consumption of each layer: 0.1-0.15 kg/m2 Minimum two coats should be applied Total consumption: approx. 0.2-0.3 kg/m2 Recoating: Do not exceed 48 hours between each coats. Application must be repeated if this time is exceeded
Wall Guards: Product origin : China Key Specifications/Special Features : Vinyl 2/3mm Thick Strips White 3mtr Length X 200mm Width Minimum Order Size and Packgaing details : 50 Pcs. - Export Cartons Usage : Office/Hospital to protect from crash-double sided tape to install
Length 800mm,1000mm,1200mm Model DJB-800/420 DJB-1000/300 DJB-1200/300 Material 27simn Width 100mm Height 90mm Thickness 8mm Length 1000mm Processing quenching and tempering (heat treatment) Load capacity larger than 300kN -
DESCRIPTION a premium cement based finish skimcoat which contains selected filler, additive and polymer used for smooth finishing to uneven concrete wall & ceiling. After dry STARCOAT CN have a excellent adhesion to the substrate, better impact resistant, no powdery, no cracks, smooth and ready to be painted with water based wall paint. Easy to use, good workability and have a long pot life and correction time even at the outdoor applications. USES IN APPLICATIONS 1. Cement Based Wall Plaster. 2. Concrete Wall, Column & Ceiling 3. Precast Concrete & Concrete profile 4. Internal & External. ADVANTAGE * Light, good workability and sanding properties. * No cracks and hair cracks. (depends on background) * Smooth surface, solid and no powdery. * Can be painted or finished with wallpaper directly after dry in minimum 24 hours * without using PVA putty to leveling up & filling uneven rough surface. PRODUCT SPESIFICATIONS 1. Main Binder : Portland Cement & Polymer 2. Filler : Limestone 3. Color : GREY and WHITE. 4. Mixing Ratio : 7 - 8 litres of water per 25 Kg bags. or 28 - 32 % water demands. 5. Coverage : 1.25-1.3 Kg/m2/mm or 19m2/25 Kg/mm thickness average 7.5m2/25Kg for 2-3mm thickness 6. Thickness : 2mm thickness/coat 4mm for 2 coats and 6mm for 3 coats. 7. Pot Life : approx. 60 minutes SURFACE PREPARATION * The substrate must be clean and free from grease and loose particles. Recesses should be pre-patched and levelled where appropriate. * Porous and absorbent substrates must be pre-wetted prior to application of Starcoat CN finish coat.
DESCRIPTION STARCOAT PL, is fine grade cement based finish plastering skimcoat which contains selected filler and additive used for smooth finishing to uneven wall cement based plaster and ceiling. After dry STARCOAT PL have a good adhesion to the substrate, no cracks, smooth, no dust on the surface and ready to be painted with water based paint. Easy to use, good workability and have a long pot life and correction time even at the outdoor applications. USES IN APPLICATIONS *Cement Based Wall Plaster. *Precast Concrete. *Concrete Profile & Concrete Ceilings *Internal & External. ADVANTAGE *Light, good workability and sanding properties. *No cracks and hair cracks. (depends on background) *Smooth surface, solid and no powdery. *Can be painted or finished with wallpaper directly after dry in minimum 24 hours without using PVA putty to leveling up & filling uneven rough surface. PRODUCT SPESIFICATIONS 1. Main Binder : Portland Cement & Polymer 2. Filler: Limestone 3. Color: GREY and WHITE. 4. Mixing Ratio : 7 - 8 litres of water per 25 Kg bags. or 28 - 32 % water demands. 5. Coverage: 1.25-1.3 Kg/m2/mm or 19m2/25 Kg/mm thickness average 7.5m2/25Kg for 2-3mm thickness 6. Thickness: 2mm thickness/coat 4mm for 2 coats and 6mm for 3 coats. 7. Pot Life: approx. 60 minutes SURFACE PREPARATION 1. The substrate must be clean and free from grease and loose particles. Recesses should be pre-patched and levelled where appropriate. 2. Porous and absorbent substrates must be pre-wetted prior to application of Starcoat PL finish coat.
DESCRIPTION AS-600 is a high-solid, solvent-based polyurea coating. Itâ??s also formulated with pure aliphatic resin and contains UV filters, remaining unaffected by the sunlight and adverse weather conditions. It cures fast providing quick tack free time (1-2 hours), allowing most projects to be completed within one day. CHARATERISTIC * Fast drying and fast curing * Brushable * Abrasion and mechanical stress resistant * Chemical resistant (in diluted acids-alkalis, car oils, petroleum, etc) APPLICATION AREAS * Warehouse ramps, garages, terraces, parking areas * Outdoor and indoor stores, industrial shop floors * Outdoor laundries, gas station, etc..
Specifications: 80, 100, 125, 150, 175, 200, 250, 300, 350, 400, etc. Introduction: Non-asbestos fiber cement piping is an environmentally-friendly piping material free of harmful asbestos, produced from harmless fiber and high-grade cement through the use of leading and complicated technology, and is extensively used for projects such as water drainage, disposal of plant sewage, exhaust, flue and cable protective piping. The piping material can be customized according to customers'different demands for diameter, wall thickness and length and ordered according to users' demands.
The expanded metal plaster mesh is also a reinforcing material that we can often find in interior decoration, which is formed by cutting and stretching, so that it without bends or welds, and it is basically no loss in the production process so that cost savings. In addition, the ribbed surface makes it has the max adhesion, so it can be used in many different kinds of surface, such as concrete, brick, wood, or even plaster ceilings, but it must be fixed with nails to ensure the plastering easier.
The expanded metal plaster mesh is also a reinforcing material that we can often find in interior decoration, which is formed by cutting and stretching, so that it without bends or welds, and it is basically no loss in the production process so that cost savings. In addition, the ribbed surface makes it has the max adhesion, so it can be used in many different kinds of surface, such as concrete, brick, wood, or even plaster ceilings, but it must be fixed with nails to ensure the plastering easier.
Rock wool is a high quality thermal insulation material with low thermal conductivity. Suitable for medium and large diameter pipes; medium and small storage tanks; curved surfaces with small radius of curvature or surface irregularities. Rock wool is made of basalt,After being melted, adopted four-roller centrifugal cotton process to throw the high-temperature basalt-cotton into a 4-7 μm non-continuous fiber. Our rock wool PH value between 7-9, soluble chloride ion content is low, in addition to the non-corrosive steel structure and metal structure, the main features are as follows: Thermal insulation: The thermal conductivity of rockwool at normal temperature (around 25°C) is usually between 0.03 and 0.047W/. Non-combustion : The combustion performance of rock wool products depends on the amount of flammable binders. Rock wool is an inorganic mineral fiber, non-flammable. Sound insulation: rock wool products have excellent sound insulation and sound absorption properties. The mechanism of sound absorption is that this product has a porous structure. When sound waves pass through, friction is generated due to the effect of flow resistance, and part of the sound energy is absorbed by the fibers. Impede the transmission of sound waves. Can be cut according to the security, less security, easy construction Tanks, such as gas and liquid storage, play an important role in every major area of industry. In order to preserve the material and ensure the stability and safety of the production process, it is important to maintain the temperature inside the tank. If the internal temperature of the oil tank is too high, not only the volatile loss of the oil will increase, but also the environmental pollution will be accelerated, and if the temperature is too low, the objects in the tank will become viscous so that the fluidity of the oil will decrease and the oil tank is outdoor for a long time, so when selecting the insulation material, it must have two functions: low thermal conductivity and waterproof performance Rock wool has been tested without asbestos, CFC, HFC, HCFC, and other environmentally harmful substances. It will not be corroded or produce mildew and bacteria. It has excellent performance for the insulation of oil tanks. As a thermal insulation material, rock wool can increase the thermal insulation resistance of the tank walls, reduce the heat transfer coefficient, and reduce the cold/heat transfer through the wall by 70%. This reduces energy loss and saves energy costs. Rock wool is a high quality thermal insulation material with low thermal conductivity. Suitable for medium and large diameter pipes; medium and small storage tanks; curved surfaces with small radius of curvature or surface irregularities. Rock wool is made of basalt,After being melted, adopted four-roller centrifugal cotton process to throw the high-temperature basalt-cotton into a 4-7 μm non-continuous fiber. Our rock wool PH value between 7-9, soluble chloride ion content is low, in addition to the non-corrosive steel structure and metal structure, the main features are as follows: Thermal insulation: The thermal conductivity of rockwool at normal temperature (around 25°C) is usually between 0.03 and 0.047W/. Non-combustion : The combustion performance of rock wool products depends on the amount of flammable binders. Rock wool is an inorganic mineral fiber, non-flammable. Sound insulation: rock wool products have excellent sound insulation and sound absorption properties. The mechanism of sound absorption is that this product has a porous structure. When sound waves pass through, friction is generated due to the effect of flow resistance, and part of the sound energy is absorbed by the fibers. Impede the transmission of sound waves. Can be cut according to the security, less security, easy construction Tanks, such as gas and liquid storage, play an important role in every major area of industry. In order to preserve the material and ensure the stability and safety of the production process, it is important to maintain the temperature inside the tank. If the internal temperature of the oil tank is too high, not only the volatile loss of the oil will increase, but also the environmental pollution will be accelerated, and if the temperature is too low, the objects in the tank will become viscous so that the fluidity of the oil will decrease and the oil tank is outdoor for a long time, so when selecting the insulation material, it must have two functions: low thermal conductivity and waterproof performance Rock wool has been tested without asbestos, CFC, HFC, HCFC, and other environmentally harmful substances. It will not be corroded or produce mildew and bacteria. It has excellent performance for the insulation of oil tanks. As a thermal insulation material, rock wool can increase the thermal insulation resistance of the tank walls, reduce the heat transfer coefficient, and reduce the cold/heat transfer through the wall by 70%. This reduces energy loss and saves energy costs.
ANO-Step: The picture above is what we produce with dimensions width 155mm ,length 135 mm ,plug is 50mm and diameter is 25 mm . Product of origin : Greece Minimum order of steps are : 1500. And packaging is as request by customer .
