1. PRODUCT OVERVIEW VHB Pot Bearings made by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are in compliance with standards (TCVN 10268: 2014, AASHTO LRFD: 2007 â?? Section 18, ASTM D 5212 â?? 03, BS5400, EN1337, KS4420). VHB Pot Bearings are capable of withstanding high loads, displacements and rotation angles. This type of bearing is suitable for middle-range span structure, continuous bridge structure, etc. with a load capacity of up to 60000kN or above depending on projectsâ?? requirements. VHB pot bearings have a well-shaped structure, superior design, which are convenient for installation and maintenance during operation. 2. PRODUCT CHARACTERISTICS VHB pot bearings are comprised of 4 main parts: top plate, piston, pot plate and elastomeric pad. The elastomeric pad is placed inside of pot plate, under the pressure of the load, the elastomeric pad experiences the temporary deformation inside the pot plate volume, it is capable of withstanding the forces and allows the movement as well as rotation along the horizontal axis. Piston and pot plate work as the connecting parts between the structures. Besides, the plus guiding part can be designed to limit or allow the movements as required from the structures. Pot Bearings are divided into 2 main types: Fixed pot bearings and sliding pot bearings. Fixed pot bearings: The bearings only allows the head of structure to have rotary movement and transfer the pressure through a fixed point. Sliding pot bearings: This type of bearings includes Free sliding bearings and Guide sliding bearings, which allows the dead to have both rotary movements and unidirectional or multidirectional movements. To ensure the long-life durability, VHB pot bearings are protected against corrosion by the following methods: painting with two-component epoxy coat, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg coating spraying method (at the ratio of 5% Al and 95% Mg) which ensures the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours.
Pot Bearing
PRODUCT OVERVIEW VSR Elastomeric Bearings made by Vinh Hung investment and production Co., Ltd (Vinh Hung IP) are in compliance with TCVN 10308: 2014, AASHTO LRFD â?? Section 18, AASHTO M 251 â?? 96 (2011), BS5400, EN1337, KSF4420 VSR Elastomeric Bearings have been used in road bridge constructions, with a maximum load of 5000kN. 2. PRODUCT CHARACTERISTIC Elastomeric bearings are composed of rubber and steel plates which are chemically bonded through vulcanization. The thickness of the bearing is calculated to ensure the load, displacement and rotation as the requirement. Elastomeric bearings are simple geometric structures, bringing convenience during the installation, operation and maintenance. In addition, this type of bearing provides high resistance of vibrations impacted to the bridge span structures and piers.
VHB pot bearing made by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are in compliance with standards (TCVN 10268:2014, AASHTO LRFD: 2007, Section 18, ASTM D521203, BS5400, EN1337, KS4420). VHB pot bearing is capable of withstanding high loads, displacements and wide angle rotation. This type of bearing is suitable for middle-range span structure, continuous bridge structure etc. with a load capacity of 60000kN or above depending on projects requirements. VHB pot bearing has well-shaped structure, superior design, which is convenient for installation and maintenance during operation PRODUCT CHARACTERISTICS VHB pot bearing is comprised of 4 main parts: top plate, piston, pot plate and elastomeric pad. The elastomeric pad is placed inside of pot plate, under thepressure of the load, the elastomeric pad experiences the temporary deformation inside the pot plate volume, it is capable of withstanding the forces and allows the movement as well as rotation along horizontal axis. Piston and pot plate work as the connecting parts between the structures. Besides, the plus guiding bar can be designed to limit or allow the movements as required from the structures. Pot bearing is divided into 2 main types: Fixed pot bearing and sliding pot bearing. Fixed pot bearing: The bearing only allows the head of structure to have rotary movement and transfers the pressure through a fixed point. Sliding pot bearing: This type of bearing, including free sliding bearing and guided sliding bearing, allows the head to have both rotary movements and transversally or multidirectional movements. To ensure the long-life durability, VHB pot bearing is protected against corrosion by the following methods: two-component epoxy coat, PU-based painting (Polyurethane), hot dip galvanization according to ASTM A123 standards and especially the Al â?? Mg spraying method (at the ratio of 5% Al and 95% Mg) which ensures the anti-corrosion durability of up to 100 years, proven by salt-spraying test in 6000 hours (8-hour dry-wet cycle repetition) under ASTM B117 standards.
1. PRODUCT OVERVIEW VHB pot bearing made by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are in compliance with standards (TCVN 10268:2014, AASHTO LRFD: 2007, Section 18, ASTM D5212â??03, BS5400, EN1337, KS4420). VHB pot bearing is capable of withstanding high loads, displacements and wide angle rotation. This type of bearing is suitable for middle-range span structure, continuous bridge structure etc. with a load capacity of 60000kN or above depending on projects requirements. VHB pot bearing has well-shaped structure, superior design, which is convenient for installation and maintenance during operation PRODUCT CHARACTERISTICS VHB pot bearing is comprised of 4 main parts: top plate, piston, pot plate and elastomeric pad. The elastomeric pad is placed inside of pot plate, under the pressure of the load, the elastomeric pad experiences the temporary deformation inside the pot plate volume, it is capable of withstanding the forces and allows the movement as well as rotation along horizontal axis. Piston and pot plate work as the connecting parts between the structures. Besides, the plus guiding bar can be designed to limit or allow the movements as required from the structures. Pot bearing is divided into 2 main types: Fixed pot bearing and sliding pot bearing. Fixed pot bearing: The bearing only allows the head of structure to have rotary movement and transfers the pressure through a fixed point. Sliding pot bearing: This type of bearing, including free sliding bearing and guided sliding bearing, allows the head to have both rotary movements and transversally or multidirectional movements. To ensure the long-life durability, VHB pot bearing is protected against corrosion by the following methods two-component epoxy coat, PU-based painting (Polyurethane), hot dip galvanization according to ASTM A123 standards and especially the Al Mg spraying method (at the ratio of 5% Al and 95% Mg) which ensures the anti-corrosion durability of up to 100 years, proven by salt-spraying test in 6000 hours (8-hour dry-wet cycle repetition) under ASTM B117
1. Product Overview VSR Elastomeric Bearings made by Vinh Hung investment and production Co., Ltd (Vinh Hung IP) are in compliance with TCVN 10308: 2014, AASHTO LRFD Section 18, AASHTO M 251 96 (2011), BS5400, EN1337, KSF4420 VSR Elastomeric Bearings have been used in road bridge constructions, with a maximum load of 5000kN. 2 PRODUCT CHARACTERISTIC Elastomeric bearings are composed of rubber and steel plates which are chemically bonded through vulcanization. The thickness of the bearing is calculated to ensure the load, displacement and rotation as the requirement. Elastomeric bearings are simple geometric structures, bringing convenience during the installation, operation and maintenance. In addition, this type of bearing provides high resistance of vibrations impacted to the bridge span structures and piers.
1. Product Overview VHC spherical Bearings/ Bridge bearing manufactured by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are capable of withstanding the high loads and movements suitable for structures requiring the rotary angle equal or bigger than 0.015 rad in all directions. VHC spherical bearings are designed and manufactured according to current standards such as: TCVN 11823, AASHTO LRFD, ASTM D5977, EN 1337, 2. PRODUCT CHARACTERISTICS VHC spherical bearings/ bridge bearing possesses a bottom plate (6) which has a PTFE sliding plate (4) on it is upper curved surface. A convex calotte (5) is placed on top of this, which, thanks to it is polished hard-chromium plated surface, can slide within the lower part with low friction, thus facilitating rotations about every axis. A second sliding plate of PTFE (4) is recessed into the upper surface of the calotte. Together with the upper plate (2) above it, this accommodates longitudinal and/or transverse sliding movements of the superstructure, if required. To reduce sliding resistance to a minimum, the lower surface of the top plate features a polished stainless steel sheet. In the case of bearings which should allow movement along one axis only, the direction of movement is controlled by guiding bars (3). In the case of fixed bearings, the top plate does not have a stainless steel sheet. The bearing is connected to the superstructure and the substructure by means of anchor dowels (1) or threaded sleeves (depending on design), or alternatively by means of separate anchor plates with shear studs. To ensure the long-life durability, VHC spherical bearings are protected against corrosion by the following methods: coating with two-component epoxy, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg spray coating method (at the ratio of 5% Al and 95% Mg) which ensure the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours (8-hour dry-wet cycle) according to ASTM B117
1. PRODUCT OVERVIEW VHB Pot Bearings made by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are in compliance with standards (TCVN 10268: 2014, AASHTO LRFD: 2007 Section 18, ASTM D 5212 03, BS5400, EN1337, KS4420). VHB Pot Bearings are capable of withstanding high loads, displacements and rotation angles. This type of bearing is suitable for middle-range span structure, continuous bridge structure, etc. with a load capacity of up to 60000kN or above depending on projectsâ?? requirements. VHB pot bearings have a well-shaped structure, superior design, which are convenient for installation and maintenance during operation. 2. PRODUCT CHARACTERISTICS VHB pot bearings are comprised of 4 main parts: top plate, piston, pot plate and elastomeric pad. The elastomeric pad is placed inside of pot plate, under the pressure of the load, the elastomeric pad experiences the temporary deformation inside the pot plate volume, it is capable of withstanding the forces and allows the movement as well as rotation along the horizontal axis. Piston and pot plate work as the connecting parts between the structures. Besides, the plus guiding part can be designed to limit or allow the movements as required from the structures. Pot Bearings are divided into 2 main types: Fixed pot bearings and sliding pot bearings. Fixed pot bearings: The bearings only allows the head of structure to have rotary movement and transfer the pressure through a fixed point. Sliding pot bearings: This type of bearings includes Free sliding bearings and Guide sliding bearings, which allows the dead to have both rotary movements and unidirectional or multidirectional movements. To ensure the long-life durability, VHB pot bearings are protected against corrosion by the following methods: painting with two-component epoxy coat, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg coating spraying method (at the ratio of 5% Al and 95% Mg) which ensures the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours.
1. Product Overview VSR Elastomeric Bearings made by Vinh Hung investment and production Co., Ltd (Vinh Hung IP) are in compliance with TCVN 10308: 2014, AASHTO LRFD Section 18, AASHTO M 251 96 (2011), BS5400, EN1337, KSF4420 VSR Elastomeric Bearings have been used in road bridge constructions, with a maximum load of 5000kN. 2. Product Characteristic Elastomeric bearings are composed of rubber and steel plates which are chemically bonded through vulcanization. The thickness of the bearing is calculated to ensure the load, displacement and rotation as the requirement. Elastomeric bearings are simple geometric structures, bringing convenience during the installation, operation and maintenance. In addition, this type of bearing provides high resistance of vibrations impacted to the bridge span structures and piers.
1. Product Overview VHC spherical Bearings/ Bridge bearing manufactured by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are capable of withstanding the high loads and movements suitable for structures requiring the rotary angle equal or bigger than 0.015 rad in all directions. VHC spherical bearings are designed and manufactured according to current standards such as:TCVN 11823, AASHTO LRFD, ASTM D5977, EN 1337, 2. Product Characteristics VHC spherical bearings/ bridge bearing possesses a bottom plate (6) which has a PTFE sliding plate (4) on it is upper curved surface. A convex calotte (5) is placed on top of this, which, thanks to it is polished hard-chromium plated surface, can slide within the lower part with low friction, thus facilitating rotations about every axis. A second sliding plate of PTFE (4) is recessed into the upper surface of the calotte. Together with the upper plate (2) above it, this accommodates longitudinal and/or transverse sliding movements of the superstructure, if required. To reduce sliding resistance to a minimum, the lower surface of the top plate features a polished stainless steel sheet. In the case of bearings which should allow movement along one axis only, the direction of movement is controlled by guiding bars (3). In the case of fixed bearings, the top plate does not have a stainless steel sheet. The bearing is connected to the superstructure and the substructure by means of anchor dowels (1) or threaded sleeves (depending on design), or alternatively by means of separate anchor plates with shear studs. To ensure the long-life durability, VHC spherical bearings are protected against corrosion by the following methods: coating with two-component epoxy, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg spray coating method (at the ratio of 5% Al and 95% Mg) which ensure the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours (8-hour dry-wet cycle) according to ASTM B117
1. PRODUCT OVERVIEW VHC spherical Bearings/ Bridge bearing manufactured by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are capable of withstanding the high loads and movements suitable for structures requiring the rotary angle equal or bigger than 0.015 rad in all directions. VHC spherical bearings are designed and manufactured according to current standards such as: TCVN 11823, AASHTO LRFD, ASTM D5977, EN 1337, â?¦ 2. PRODUCT CHARACTERISTICS VHC spherical bearings/ bridge bearing possesses a bottom plate (6) which has a PTFE sliding plate (4) on it is upper curved surface. A convex calotte (5) is placed on top of this, which, thanks to it is polished hard-chromium plated surface, can slide within the lower part with low friction, thus facilitating rotations about every axis. A second sliding plate of PTFE (4) is recessed into the upper surface of the calotte. Together with the upper plate (2) above it, this accommodates longitudinal and/or transverse sliding movements of the superstructure, if required. To reduce sliding resistance to a minimum, the lower surface of the top plate features a polished stainless steel sheet. In the case of bearings which should allow movement along one axis only, the direction of movement is controlled by guiding bars (3). In the case of fixed bearings, the top plate does not have a stainless steel sheet. The bearing is connected to the superstructure and the substructure by means of anchor dowels (1) or threaded sleeves (depending on design), or alternatively by means of separate anchor plates with shear studs. To ensure the long-life durability, VHC spherical bearings are protected against corrosion by the following methods: coating with two-component epoxy, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg spray coating method (at the ratio of 5% Al and 95% Mg) which ensure the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours (8-hour dry-wet cycle) according to ASTM B117
1. PRODUCT OVERVIEW VHC spherical Bearings/ Bridge bearing manufactured by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are capable of withstanding the high loads and movements suitable for structures requiring the rotary angle equal or bigger than 0.015 rad in all directions. VHC spherical bearings are designed and manufactured according to current standards such as:� TCVN 11823, AASHTO LRFD, ASTM D5977, EN 1337, 2.PRODUCT CHARACTERISTICS VHC spherical bearings/ bridge bearing possesses a bottom plate (6) which has a PTFE sliding plate (4) on it is upper curved surface. A convex calotte (5) is placed on top of this, which, thanks to it is polished hard-chromium plated surface, can slide within the lower part with low friction, thus facilitating rotations about every axis. A second sliding plate of PTFE (4) is recessed into the upper surface of the calotte. Together with the upper plate (2) above it, this accommodates longitudinal and/or transverse sliding movements of the superstructure, if required. To reduce sliding resistance to a minimum, the lower surface of the top plate features a polished stainless steel sheet. In the case of bearings which should allow movement along one axis only, the direction of movement is controlled by guiding bars (3). In the case of fixed bearings, the top plate does not have a stainless steel sheet. The bearing is connected to the superstructure and the substructure by means of anchor dowels (1) or threaded sleeves (depending on design), or alternatively by means of separate anchor plates with shear studs. To ensure the long-life durability, VHC spherical bearings are protected against corrosion by the following methods: coating with two-component epoxy, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg spray coating method (at the ratio of 5% Al and 95% Mg) which ensure the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours (8-hour dry-wet cycle) according to ASTM B117
Material : Steel Contact Angle : 0 Lube Hole Center : 0.179 in Eccentric Collar Offset : 0.188 in Rows of Balls : Single Preload Level : None Static Load Rating [Max] : 4,600.0 lbf Bearing Type : Radial Width [Nom] : 2.219 in Precision : Standard Radial Internal Clearance : C3 Cage Type : Metal Origin : Wide Inner Ring Seal Protection Width : 1.070 in Collar No. : S1112K Locking Device : Eccentric Locking Collar Snap Ring : No Snap Ring Precision Level : Standard (ABEC 1) No. in Set : Single Bearing O.D. [Nom] : 3.3465 in .D. Type : Straight Cage Material : Steel Inner Ring Width : 1 11/16 in Inch/Metric : Inch Bore Outer Ring Width : 22.000 mm Collar O.D. : 2 1/2 in Capacity : Standard Capacity Bore Type : Round Bore Seal O.D. : 2.908 mm Enclosure : Double Sealed Ball Material : Steel Temperature Range [Max] : 275 F Seal Material : Rubber Seal Type : Contact Seals Temperature Range [Min] : -30 F Dynamic Load Rating [Nom] : 8,160.00 lbf I.D. : 1 3/4 in Radial Internal Clearance Specification: Greater Than Normal Clearance Collar Width : 0.719 in Lubricant : Polyurea Base
Model SG15 Material Chrome steel Row: Double Row Dimension:5*17*8mm G.W CTN 23Kg
Model :SG10 Material : chrome steel Row: double row U type grooved Dimension :4*13*6 G.W :23kg
Model:681 Material: chrome steel Dimension:1*3*1mm MOQ1000pcs Package: ploybag
Model :MF52 Precision :ABEC-5 Material: Chrome steel Dimension:2*5*2.5mm Package : Plastic tube
Model:6202zz Precision:V3 Material:Chrome steel Dimension:15*35*11 Package: Plastic tube G.W:23Kg
Model 694zz Dimension:4*11*4mm Precision: P0 Sealed type:zz Material: Chrome steel Package: Plastic tube G.W CTN:23kg
Material: Chrome steel Ball material: White ceramic ball Model 608 RS Dimension 8*22*7mm Package: Plastic tube G.W CTN:23Kg
