JCID AiXun Face ID Dot Projector Precision Calibrator For Phone X XS/XR 11/11 Pro/11 Pro Max Faceid Flex Cable Alignment Repair Tool. Instructions: Step 01: Buckle the face ID module. Put the corresponding dot projector face lD module into the alignment calibrator base. Step 02: Put on the top cover Built In strong magnetic adsorption, fix it more firmly and align accurately. Step 03: Adjust the dot projector flex cable Move the cable slightly to complete alignment. Do not force the module. After alignment, there ls no gap between the cover plates. Product Size: 50mm 16mm 8mm Package Size: 85mm 55mm 25mm Features: 1. Precise alignment and quick fit. 2. Reset test of iron frame deformation. 3. Realize the standardized maintenance of dot projector alignment. 4. Standard positioning, magnetic reset. 5. Transparent polymer materials. 6. Suitable: X/XS/XSM+XR 11/11Pro/MAX
SS-T12A Heating Station Main Unit with T12A-X3 / T12A-CPU / T12A-F/ T12A-Face ID/ T12-andriod / T12-N12/ T12-N13 Motherboard Heating groove for Phone X-13 Pro Max Android Phone motherboard CPU Face ID repair. SS-T12A Heating Station Main Unit + Five kinds Motherboard Heating groove. T12A-X3 for X / XS / XMAX T12A-CPU T12A-F T12A-Andriod T12A-Face ID T12-N12 for Phone 12/12 Pro/12 Pro MAX/ 12 MINI T12-N13 for Phone 13/13 Pro/13 Pro max/13 mini Added T12A-N11 for phone 11 pro max motherboard SUNSHINE SS-T12A Phone X upper / lower motherboard pre-heating station adopt special heating design and precise temperature control capability, which will locate accurately locate the needed heating part. SS-T12A has dual bayonet design to make phone X motherboard stable. SUNSHINE SS-T12A has EU, AU, and US plug, 110V or 220V for your choice. Using high purity copper to guarantee heat transfer, which is not easy for deformed, durable and anti-wear. 100V-240V SS-T12A Phone X mainboard stratified 185 degrees accurate rapid separated disassembly heating station. Phone X logic board was folded in half, two layers then were soldered together, the upper layer is the mainboard, and the lower layer is the signal board. Which made our repair much difficult to proceed, how to repair Phone X logic board in fast and efficient method, need the professional Phone X motherboard repair tools Features : Adopting 185-degree layered process to remove the iP-X motherboard, not only from our fine analysis of iP-X solder paste ,but depends on the special heating design and precise temperature control of SS-T12A. SS-T12A only heats the area that the IP-X board needs to be removed to prevent improper heating. Dual bayonet design, make sure the iP-X motherboard is stable on the stage. High purity copper is used as a film to ensure uniform heat transfer and heat.
Film Shrinkage Test Equipment Film Shrinkage Tester GBK-D1 Film Shrinkage test, known as linear thermal shrink test or free shrink test, is used for analyzing the effect of temperature on heat shrinkable films made from polyethylene, ethylene copolymers and their mixtures. Basically, shrinking force, contracting force and shrinking ratio can be measured in such determination. GBPI Film Shrinkage tester conforms to the multiple national and international standards: ASTM D2732 - Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting ISO 14616 - Plastics Heatshrinkable films of polyethylene, ethylene copolymers and their mixtures Determination of shrinkage stress and contraction stress DIN 53369 - Testing of plastic films determination of the shrinking stress Film Shrinkage Test Equipment GBK-D1 is used to determination of the degree of unrestrained linear thermal shrinkage and dimensional stability at different temperatures. Widely used in industries of plastic material, plastic products, petroleum, chemicals, research institute, inspection agency and so on. Principle This tester uses the principle of air heating to connect the tested sample to the tension sensor and displacement sensor. After reaching the maximum shrinkage force, it is placed in an external test environment with an ambient temperature of 23 to cool down. The reference temperature, shrinkage force and displacement are recorded, and the recorded data can be used to determine the optimal shrinkage conditions of the film. Standards ISO 14616, ASTM D2732, DIN 53369
Product Name : Antimagnetized wire thread insert supplier Material : Stainless steel, copper alloy, high temperature alloy. Advantage : High strength, high bearing capacity, high wear-resisting, high corrosion resistant Surface Treatment : Natural, silver plating, cadmium plated, colourful Specifications : GB/MS/MA/BS/AS Standard ones and customized Packing : Cartoons or wooden cases a professional design, research and development and production of thread inserts and tools of professional manufacturers. We produce customized thread inserts, self tapping inserts, tailless nesting, keensert and installation tools for inserts. We have also passed the GB / T 19001-2016 / iso9001:2015 standard and GJB9001c-2017 standard certification, and have relevant SGS certification.
Product Name : Tangless thread insert supplier Material : Stainless steel, copper alloy, high temperature alloy. Advantage : High strength, high bearing capacity, high wear-resisting, high corrosion resistant Surface Treatment : Natural, silver plating, cadmium plated, colourful Specifications : GB/MS/MA/BS/AS Standard ones and customized Packing : Cartoons or wooden cases More detailes please contact
Product Name : Wire thread insert repair kits Material : Stainless steel, 304 steel Type : Automatic, manual operation Application : For installing or removing or repairing the wire thread inserts Payment terms : T/T Packing : Cartoons or wooden cases
Product Name : Material : Stainless steel, copper alloy, high temperature alloy. Advantage : High strength, high bearing capacity, high wear-resisting, high corrosion resistant Surface Treatment : Natural, silver plating, cadmium plated, colourful Specifications : GB/MS/MA/BS/AS Standard ones and customized Warranty : 12 months Packing : Cartoons or wooden cases
1.High-precision calibration: charging current, discharge current, charging voltage and discharge voltage are all calibrated by Agilent with high precision to ensure the accuracy of current and voltage within 0.5%. 2.Independent channels with configurable parameter and condition setting for each individual channel. 3.Equipped with complete input and output devices, hardware and software protection, polarity reverse protection, power failure protection and etc. 4.Precise control without overshoot during CC-CV and CV-CC transition. 5.Strong software system and friendly HMI (Human-Machine-Interface). 6.Multiple conditions (capacity, time, open circuit voltage, discharge platform, etc.) for battery sorting. 7.Automatically calculate the constant current charge ratio, capacity loss, discharge efficiency, average voltage, median voltage and other data. 8.Equipment hardware control loop uses current and voltage double loop control. No ripple for constant current and constant voltage switching. 9.Data exported as EXCEL and TXT files, as well as chart files, can be shown as data analysis waves for charging and discharging, voltage, capacity, current & time feature.
specially for silage purpose power source - electric Motor / Engine power required - 3hp material feed - Straw, Dry grass, fresh grass, corn stalk, bamboo other cutting size - 0.8mm to 10mm
When the 30KW electric rake winch for coal mines is used to rake the mine underground, the temporary fixing method is generally adopted, and there is no permanent fixed foundation. The fixing must be firm, and the fixing pile of the machine must be checked frequently for signs of loosening. Any problems should be dealt with in time to ensure the safe operation of the equipment. Model: 2JP-30/2JPB-30 Average pulling force of main wire rope (KN): 27.5 Main wire rope speed (m/s): 1.20 Sub wire rope speed (m/s): 1.60 Average wire rope speed (m/s): 1.4 Motor model: Y200L-4/YBK3-200L-4 Motor power (KW): 30 Main drum rope capacity (m): 70 Main drum dia (mm): 280 Main drum width (mm): 156 Main wire rope dia (mm): 16 Main wire rope structure: 619 Main wire rope minimum breaking force (KN): 143
Pipeline system inflatable air grip union Seal o grip union air o union are air inflatable connections for low pressure fluid or mud suction and return lines. The seal o grip carbon steel body welds in place on mud tanks or manifold pipe. A leak right seal is achieved with rig supplied compressed air, even if the connecting pipe is not perfectly aligned. The oil and abrasion resistant NBR pneumatic o tube can be inflated up to 200 PSI against the outside diameter of the connecting pipe, speeding field set up and eliminating the need for low pressure flanged connections. Features Low requirement to centered when installed, to achieve quick install and seal. The pipeline can be removed without other tools after pneumatic union deflated, adaptable and easy maintenance. No wrenches, bolts & nuts required. Fast and easy make up without close alignment. Pneumatic Tube inflatable up to 200 PSI.
1. This didactic equipment can simulate normal engine operation, ie. starting, idling, acceleration, deceleration, fault detection and diagnosis, fault simulation, etc. 2. Equipped with fault simulation systems can simulate multiple failures in the real engine. 3. Equipped with voltmeter to show the real-time change of the sensors and actuators 4. Equipped with LED light to simulate the status of the injecting system and ignition system. 4. Equipped with pressure gauges to display the pressure value and vacuum pressure value. 5. Equipped with diagnosis seat which can use a scanner to read the fault codes and data flow of the engine control system through the diagnosis seat. 6. The training panel is printed with the color circuit schematics which makes the students can understand and analyzing the engine control system directly. 7. There are test terminals mounted on the training panel. electrical signal, such as the resistance, voltage, current, frequency, waveform of the sensors, actuators can be measured by multimeter or oscilloscope through the test terminals. 8. Equipped with power switch, tank guard, flywheel and other rotating parts shields to protect the students and teachers. 9. Equipped with fault setting module: manual fault set module.
1.Introduction of remote control a.Product Composition Siemens real-time coordinate display wireless electronic handwheel consists of two parts: electronic handwheel receiver; b.Characteristics The wireless transmission distance is open 40 meters, automatic frequency hopping technology, can use 32 sets of equipment at the same time; The electronic handwheel is powered by 2 AA batteries and can be used for more than 30 days; The receiver is equipped with an external antenna to enhance the signal and is easy to install; Electronic handwheel support: one 100PPR encoder one 6-speed axis selection switch one 3-speed magnification switch; Electronic handwheel supports 6 custom buttons, corresponding to Siemens PLC address, which can be freely programmed; 6 custom buttons can control 6 switch outputs; The display screen displays the PLC corresponding register coordinate value in real time, and supports 6-axis display of real-time coordinates.
As a professional ODM OEM wholesale manufacturer in , Wetop Sports has been specializing in supplying the custom water sports equipment for several years, such as wetsuit, drysuit, diving mask, fins, flippers, life vest, life jacket, buoyancy aid, surfboard and other relevant accessories.
Orwind Promech Inspection Camera Borescope with Large Color LCD Screen and Video Recording, 3.2ft IP67 Waterproof Semi-Rigid Snake Endoscope Tube and 8 Brightness LED Level, Portable Toolbox Included Magnet Probe: Help grip magnetic items, such as keys, screws, nails, etc. Single Hook: Easy to hook up circle rounded units, such as rings, key chains,etc. Double Hook: Help catch up heavy things with rope or wire Features Built-in Screen: 2.31 TFT Color LCD Effective Pixels: 640 x 480 Imaging Sensor: 1/9-inch CMOS Brightness: 220 CD/M2 (TYP) Video System: PAL/NTSC Video Format: .AVI Image Format: .JPG Horizontal Viewing Angle: 48 Waterproof Rating: IP67 (For Lens/Tube Only) Orwind upgraded inspection camera is dedicated to provide you with the best experience, allowing you to see where the naked eye cannot, and assist in doing some jobs that cannot be done with hands alone. It makes industrial probe easier. The live time video streaming and photo taking function can record images and videos for detailed checking. Features include waterproof LED lens and real-time viewing. The endoscope is appropriate for use in inspecting pipes or other hard-to-reach places, equipment or furnishing installation, car repair, etc.
Single Gas Detector A single-gas detector is a device that detects the presence of any gas within an area, usually as part of a safety system. This type of Single-Gas Detector Equipment is used to detect a gas leak and interface with a control system so a process can be automatically shut down. A gas detector can also alert operators in the vicinity of the leak, allowing them to leave the area. We supply an immense choice of gas finders and screens for various applications like oxygen, combustible gases, and carbon monoxide. The gas detector adopts an embedded MCU controller detector adopts and is easy to operate, These units can be provided with sensors to recognize the most well-known gases as well as a scope of more extraordinary gases for changing applications. VS-70 xx portable gas detector locators are additionally accessible with a PID sensor to identify the presence of volatile natural compounds and with infrared IR sensors for the estimation of CO2 and other combustible gases. FEATURES : Single gas detector individually we can provide gas detectors for the following gases: Oxygen Combustible Gases LPG Hexane Hydrogen Carbon Monoxide Hydrogen Sulphide Chlorine Sulfur Dioxide Ammonia Hydrogen Chloride Hydrogen Nitric Oxide Nitrogen Dioxide Ethylene Phosphine Phosgene Ozone And Many More
Vehicle Emission Monitor Vehicle Emission Monitor is a product designed on the basis of customized sensor technology for variable gases that are emitted from the exhaust of gasoline and diesel vehicles. It is used to measure the concentration of exhaust gases discharged by vehicle engines including CO, CO2, HC, 02, etc. Our company developed the automobile exhaust gas tester in accordance with the national standards of ARAI (AUTOMOTIVE RESEARCH ASSOCIATION OF INDIA). Designed products are divided into automotive exhaust gas testers for transient and steady-state testing of gasoline and diesel vehicles, respectively. APPLICATION AREA Road inspections and random inspections Protection department's transportation department. A quick inspection of the automobile annual inspection test line and Exhaust purification device. Automotive exhausts research in teaching and research units. Automotive manufacturing industry and automotive repair 4S shops. INSTALLATION CONDITIONS Install in a location that meets the following installation conditions. The equipment is properly grounded. There is no strong magnetic field generated by heat sources or electrical appliances near the installation site (such as motors, or transformers) If possible, the equipment is qualified for leak detection. FEATURES : Developed on the Android platform, with good human-computer interaction and intelligent control Rich interfaces, can be connected to oil temperature, speed ambient temperature, humidity, pressure, and other parameters. Instruments designed the best PUC monitor, for Emission control systems in automobiles and are employed to limit the discharge of noxious gases from the internal-combustion engine and other components.
Product description Insulating boots and gloves withstand voltage device is a power frequency power supply with low voltage working voltage of 220V/50Hz for insulating boots and gloves. According to the principle of electromagnetic induction, the input voltage is changed to the minimum value required for the test. high pressure. Insulating boots (gloves) withstand voltage test device generally consists of a special dedicated test box, an intelligent power frequency withstand voltage console, and a power frequency withstand voltage test transformer. A special water tank can be customized according to needs to test 6-8 insulated boots or 6 insulated gloves at a time, and display the leakage current of the insulated boots or insulated gloves at the same time. The intelligent power frequency withstand voltage console is equipped with overcurrent protection and zero protection. Time protection and alarm function. The preventive voltage resistance test device for insulating boots and gloves is a special product developed and produced according to the needs of users according to the test procedures of insulating boots (gloves). The selection has an automatic boost (buck) function, automatically reads the leakage current of each test product, the whole process is automatically completed, and the test data is automatically printed, which effectively solves the previous non-standard test methods, thereby simplifying .Simplifies the test procedure and improves the test speed. More reliable identification of parameters such as leakage current and power frequency withstand voltage of insulating boots (gloves). To ensure the safety of test personnel, it is an ideal pre-treatment of insulating boots (gloves) to protect power frequency withstand voltage test equipment. Technical Parameters Input voltage AC220V 50 Hz Output voltage 0~30kV Capacity 3kVA Test number 3 pairs each time Quality Gloves (insulating boots) test car: 80kg; power frequency withstand voltage test bench: 70kg
Main parameters of the drone: Tank Capacity: 10L; Net Weight: 13kg; Take-off Weight: 27kg; Flying Time: 10~15min; Spray Width/Nozzle No.: 3 5m 4 Nozzles; Spray Flow: 3.5~4L min; Spray Efficiency: 5-7Ha Hr; Wind Resistance: 10m s; Machine Size Spread Size: W1.14m x L1.12m x H0.58m; Folded Size: W0.82m x L0.64m x H0.58m; Power System Motor: Brushless; Propeller: Carbon Fiber ESC: Rapid Throttle Response; Flight Control: K++ V2 Remote; Controller: Joyance Datalink T12 RC; Battery Quantity: 14S 10000mAh 1pc; Adapter + Charger: Dual-Channel Charger 2400W; Aluminum box size weight: 98 92 68cm / 60kg; Toolkit: Maintenance Repair Tools;
Main parameters of the drone: Tank Capacity: 16L; Net Weight: 18kg; Take-off Weight: 40kg; Flying Time: 10~15min; Spray Width/Nozzle No.: 4~6m / 8 Nozzles; Spray Flow: 3.5 4L/min; Spray Efficiency: 8-10Ha/Hr; Wind Resistance: 10m/s; Machine Size Spread Size: W1.4m x L1.35m x H0.7m; Folded Size: W0.88m x L0.77m x H0.8m; Power System Motor: Brushless; Propeller: Carbon Fiber ESC: Rapid Throttle Response; Flight Control: K++ V2 Remote; Controller: Joyance Datalink H12 RC; Battery / Quantity: 14S 20000mAh / 1pc; Adapter Charger: Dual-Channel Charger 3000W; Aluminum box size weight: 98 98 75cm 100kg; Toolkit: Maintenance Repair Tools; After-sales & Services: Warranty: 3 years for the agriculture drone frame; 12 months for main drone spare parts; 3 months for wearing spare parts. Ready to fly and quality control:100% tested before delivery. Lifelong after-sales service, offer operation  manual and videos, timely online technical support is available. Free training in our factory, including operation and maintenance, takes 2-3 days.
