Silicon tubing has a good property of waterproof, oil resistance, and hest resistance,etc. 100kg per carton.
NE-5130 NE-5140 NE-5150 NE-5160 NE-5170 NE-5180 Appearance milky-white,light-yellow,light-gray Density g/cm3 1.09í+0.05 1.13í+0.05 1.15í+0.05 1.18í+0.05 1.21í+0.05 1.25í+0.05 Hardness Shore A Points 30í+3 40í+3 50í+3 60í+3 70í+3 80í+3 Tensile Strength MPaí¦ 5.0 6.0 7.0 7.0 6.5 6.0 Elongation at Breakage % í¦ 440 380 320 280 200 150 Tension Set % í_ 8 9 10 10 9 8 Tear Strength kN/m í¦ 15 16 18 18 16 15 First vulcanization condition for test piece: 175íµí-5min Vulcanizator: 80% DMDBH,quantity added 0.65% 20kg/box
Silicone bakeware 1.100% food-grade silicone material 2.Non-stick finish durable and easy-cleaning 3.Welcome customer's design 4.Any color availiable
Ferro silicon 75% manganece, 15% silicon, and 10% mix. In a small pieces like 50 to 60 gm per piece
Multicrystalline silicon wafers 1.Material: multicrystalline silicon 2.Growth method: directional solidification 3.Conductivity type: p-type (boron doped), astm f42 4.Oxygen concentration: n 1, 0x1017 at./cm3, astm f 121 5.Carbon concentration: n 1x1018 at./cm3, astm f 121 * oxygen content measurement by astm 1188 and used calculation coefficient for ppm atomic is 4, 9 and and for at/cm3 is 2, 45e+17. 6.Square side: (156.0 0.5) mm 7.Symmetry as per the drawing in the enclosure no. 1 8.Thickness: (200 30) µm, astm f 533 9.Ttv: < 50 µm, astm f657 10.Bow < 50 µm, astm f 534 11.Surface saw damage depth µm < 20 (< 15 typically) 12.Saw traces µm 2 µs, astm f 28 15.Surface: as-cut and cleaned; visible contamination, oil or grease, finger prints, soap stains, slurry stains, epoxy/water stains, cracks are not allowed; edge chips under 1 mm from the edge of the wafer are allowed. . 16.Customer may request to receive reference samples 17.Wafers are being stacked into batches of 50-100 wafers each. Then it is sealed into polyethylene film. Protective paper among wafers is upon customer request. 500 -600 wafers in total are being packed into styrofoam box. Styrofoam boxes are being packed into pasteboard cases. Wafers are being packed in such a manner as to ensure minimal damage to the product during transportation. 18.All polystyrene boxes of wafers are identified with: box number; type of wafer; number of wafers per box; all contributing ingots numbers; thickness of wafers; date of packing / output inspection. Geometry: Square side angle:900, 5 Chamfer: 1, 5 mm0, 5mm at 452
Rtv-2 room-temperatue sulfureted silicon rubber Silicon flexible molds are used for mold duplication and delicate mold making for poli crafts, resin crafts, lighting and candle crafts.
Silicon ingot Silicon ingot, cement, steam coal
Silicone sealant The shundes-280n is a low moudulus silicone sealant which offers outstanding performance accoss a wide variety of glazing and construction application.It has excellent adhesion to glass, brickwork, pleastic and so on. 280ml(25/card)
Silicone oil for sealant silicone 100cs 350cs 1000cs
SEP-9200 is a one component silane end-capped polyether sealant, containing no solvent, no isocyanate, no small organic silicon molecule nor polymer.It's environmental friendly, low VOC, without contaminating substrate. It is cured by absorbing the moisture in the air at room temperature.Usually not need a primer before apply. It could adapt to thermal expansion and contraction due to inherent elasticity,It performs good adhesive to variety of construction materials such as concrete, cement, stone, glass, etc., therefore it could be commonly used.It has following characteristics: Good operability: one component, easy to apply. Environmental friendly: no solvent, low VOC, without dirt substrate. Good adhesive for variety materials, such as concrete, cement, stone, glass,etc. Excellent weather resistance Paintable
SEP2910 is a one-component high-performance anti-mold sealant, solvent-free, no free isocyanate, no silicone small molecules and polymers, no pollution of the substrate, low VOC and environmental friendly. It is cured by reaction with moisture in the air, and can be cured at room temperature. No primer required. And it can be used as building decoration gap filing and sealing. It is long-lasting anti-mold. Good operability: one component, easy to apply. Environmental friendly: no solvent, low VOC, without pollution of substrate. ood adhesive for various materials, such as glass, metal, PVC,ABS,PC,PET,PBTetc. Excellent weather resistance Paintable
SEP-1900 is a one component sealant based on silane end-capped polyether, without solvent, free isocyanate, small organic silicon molecule and polymer.It is environmental friendly, low VOC, and would not dirt the substrate, which is curing by absorbing the moisture from air in the room temperature.It performs excellent bonding to variety of construction materials, such as concrete, cement, stone, glass, ABS, PC, etc., therefore it could be widely used in construction and infrastructure areas.It has following characteristics: ï??High transparency, would not turn yellow. ï??Good operability: one component, easy to apply. Environmental friendly: no solvent, low VOC, without dirt the substrate. Excellent adhesive: bond well to variety materials, such as concrete, cement, stone, glass, and other construction materials.
MS2000 is a one component silane end-capped polyether sealant, containing no solvent, no isocyanate, no small organic silicon molecule nor polymer. It's environmental friendly, low VOC, without contaminating substrate. It is cured by absorbing the moisture in the air at room temperature. Usually not need a primer before apply. It could adapt to thermal expansion and contraction duo to inherent elasticity, It performs good adhesive to variety of construction materials such as concrete, cement, stone, glass, etc., therefore it could be commonly used.
Definition Silicones are synthetic polymer containing alternate silicone and oxygen atoms as its backbone. Silicones are made from silicon (a metal obtained from silica sand) and methyl chloride (an organic compound) in a process known as the direct process. The Silicone sealant in the uncured state normally looks like a thick paste or cream. After curing the paste turns into an impressive rubber. Applications Silicone sealant are used as a form-in-place gaskets for engine & transmission applications, sealing of exterior joints, aquarium joints bonding, sealing of bath tubs, construction and glazing application, electrical potting & encapsulation, mould making, etc. Curing Mechanism RTV silicone systems use humidity or moisture in the air during curing and cannot be accelerated using heat (excessive heat in the curing process can be detrimental). Small amounts of by-product are also produced. The cure process will only take place if the material is open to the atmosphere and curing will be adversely affected if access to humidity is removed prior to the completion of the cure process. Provided product types One component RTV silicone sealant Two component RTV silicone sealant Packing, storing, shelf life and transport Available packing sizes vary from 25 g to 25 kg, packed in lacquered coated aluminium tubes, HDPE cartridges and epoxy coated MS drums. Store products at room temperature (20C to 35C). Shelf life can vary from 4 - 12 months. They are safe to transport by road, air and sea.
Silicone sealant Appearance (uncured) : Paste Components : One component-requires no mixing Temperature resistance : -50C to +250C Typical application : Gasketing compound for automotive service market
Silicone sealant Appearance (uncured) : Paste Components : One component-requires no mixing Temperature resistance : -50C to +250 C Typical application : Gasketing compound for automotive service market
We are a professional manufacturer of heat shrink tubing and have been doing business in this field for more than 10 years, with a good reputation and many regular customers all over the world. We can also accept any kind of customized heat shrink tubing type, as well as customized outer or inner packaging. This product features: this product is made of silicone rubber modified silicone tube with heat shrinkage performance, not only has the general excellent performance of silicone tube itself, such as high temperature resistance, high pressure resistance, soft and elastic, but also has the heat shrinkage performance, good mechanical properties of puncture damage resistance, as well as long-term use is not easy to aging and other characteristics. Therefore, this product can be used in these fields: instruments, household appliances, aerospace, military, automotive manufacturing, electrical components, transformers, motors and other insulation, protection, etc. We guarantee reasonable prices and satisfactory quality, making it a good fit for your own brand. We can offer: - Competitive prices - High quality products - Sample orders accepted - Secure payment and delivery worldwide - Free shipping for bulk orders For custom production and any questions, please feel free to contact! Looking forward to be your supplier in China and have a long term cooperation. Contact us:Mors
A) Type of Wafer >Wafer : 6"-12" >Dummy/Monitor/Prime/Spacer Test Wafer 6" - 12" >Thin Wafer Thicknesss : 150um - 850um >Aluminium Wafer : 6" to 12" >Test Wafer / Oxide Wafer : 6" - 12" >Special Wafer (Nitride, SiC, LT, LN, SOI....etc) B) Types of Wafer Services > Various level (Dummy, Monitor Prime, Test, Spacer, Reclaim) >Chemical/Electroless Plating Services on Ti, Cu, AI Pad. Shipping Boxes Range: >FOSB,FOUP >Cassette: 2-12inch >MW type >Entegris type >Pizza Box
General Purpose Acetic silicone sealant Product Features Acetic cureing , quickly curing, excellent adhesion Excellent resistance to low and high temperature change Good anti-aging propetry Main Appplication All kinds of glass engineering bonding and sealing. Used for bonding various glass cabinets Storage 12 months under dry codition ,blow 27 Package 260ml/300ml 24 pieces per carton
Silway 714 water repellent is a water-dilutable solution of potassium methyl siliconate designed to impart water repellency to a wide variety of surfaces. Supplied at a concentration of 42 percent in water. Silway 714 water repellent reacts with carbon dioxide in the air to form am insoluble water-resistant treatment within 24 hours. KEY FEATURES: * Reduce water absorption into the substrate, thus reducing spalling due to freeze-thaw and efflorescence, thereby increasing the life of the substrate. * Colorless and non-yellowing protection preserves the natural appearance of the substrate. * Penetrating and breathable * Low VOC * Nonflammable
