Oil pumps have very important functions. It supplies the necessary lubrication to the important parts of internal combustion engine after absorbing the oil and compressing it. At the same time, it also circulates and delivers lubricant to the various clutches through the valve reed.
JZJW series roots-oil-free reciprocating vacuum system comprising a roots vacuum pump as the main pump, and a WLW vertical oil-free reciprocating vacuum pump as the backing pump, the two pumps is parallel connected. These system remain the advantage of large pumping speed, which belongs to ZJP series vacuum pumps, and at the same time avoid the disadvantage of low pumping speed when it comes to high ultimate vacuum, which belongs to WLW series vacuum pumps. Thus JZJW series system is widely used in the processes of vacuum distillation, vacuum evaporation and vacuum dehydration & crystallization for chemical industry;freeze-drying for food industry; vacuum drying for pharmaceutical etc. JZJW series are fit to be used to collect gases like pentadiene,benzene, methylbenzene etc,which are anti-compressed,anti-concretion in high vacuum system. All this due to that the WLW series vacuum pumps adopted the oil-free and self-lubricating materials, then it can obtain spotless vacuum. JZJW series system are the new production developed by company and National Scientific and Reach Unit. As the ideal production to protect environment,energy-saving,small occupying of area, water-saving, low noise is the system’s main characters. 1. High ultimate vacuum, long range of vacuum 2. Large pumping speed under higher vacuum 3.Lower shaft power, small consumption 4. Without second-time water pollution, the pollution is limited in small area
Each JZJ2B series roots-liquid ring vacuum system comprising a ZJP series roots vacuum pump as main pump, a SKA(2BV/2BE1) series liquid ring vacuum pump as backing pump and other valve&measure apparatus with pips to consist the unit. The units are applied to exhausting normal gases and gases with water, organic solvents or a little dust. Compared with normal mechanical vacuum pumps, the units resist oil, steam and dust. Compared with normal water ring vacuum pumps, they have high vacuums and high exhaust speeds under high vacuum, which make the unit more fit for drying dehydration and vacuum degassing in textile, food, chemical and industry fields. Comparing with common liquid ring vacuum pump,the capacity to remain high pumping speed under high or ultimate vacuum degree becomes its main advantage. Except for normal gas suction, this system can also pump special gas with small amount of vapor or dust. Additionally, this system is free from oil pollution, as well as vapor and dust. Since the 2BV type of liquid ring pump has been adopted as its fore pump, the JZJ2B series system is more efficient than JZJ2S series (which 2SK type of liquid ring pump has been adopted). And it is compact-designed with no air leakage and high protection level. Besides,our 2BV type is more anti corrosive than 2SK type, because all 2BV impeller are albronze material. Another note, the fore pump can be designed as a closed circulation system so to reduce the environment pollution greatly. JZJ2B series system has become an ideal choice for vacuum drying or dehydration process, and vacuum degassing process in the field of light textile, food industry, chemistry, pharmacy, etc.
Model 32PL spray pump is a horizontal centrifugal pump of single stage, and single suction overhang type. It is used mainly for showering, cooling and lubricating the cylinder and piston in drilling pump. It may be used also for transporting cleanwater under 80 or sewage water containing little mud and sand.When used together with drilling pump, it is driver through belt. As for operation on other cases, it can be connected directly with 4 pole motor. Function Impeller rotates generating centrifugal force, and the spray pipe assembly takes the water in the water tank to the cylinder liner, cooling and lubrication to the cylinder liner and piston. Feature 1. It has reached the world standard of the same type of products, and is very much welcomed on domestic and foreign markets. 2. It can operate normally both in positive direction and negative direction on change . 3. It is smooth in operation, convenient in installation, adjustment and maintenance. 4.This pump is a patented product. Technical Specifications Type: ordinary spray pump and electric spray pump Model Flow, Rotatespeed, m3/h rpm Kg Power, Kw Deliveryhead, m ordinaryspraypump 32PL 6.5-, 335 ¦260 28 -- 7 Electricspraypump 32PL(D) 7.5m3/h - ¦294 ¦400 -- 2.2 10 The parameters Model Flow,m3/h Lift,m Rotationspeed,rpm Efficiency,% Power,kw ShaftPower MotorPower 32SB180J-2.2 7.5 10 1420/1750 48 0.55 2.2 32SB180J-4 9 14 1750 48 0.93 4 40SB180J-3 15 10 1420/1750 53 0.78 3 32PL 7.5 10 1420 48 0.55 - 32PL(B) 7.5 10 1420 48 0.55 - We will send you a precise packing information after what kind pump you want, with the motor or not.
Product name: DT Desulfurization Pump Model: DT Desulfurization Pump Application: Can be used as the limestone slurry pump, gypsum discharge pump, filter liquid feeding pump, an absorption tower circulating pump, recycling pump etc. Product overview DT (TL) type desulphurization pump (industrial slag slurry pump), referred to as: DT (TL) desulfurization pump, is a successful design experience based manufacturing in ZJ series slurry pump, in view of our country industrial flue gas desulfurization pump characteristics, absorbing domestic and foreign advanced technology products, a new generation of series desulfurization pumps carefully the development of the. Can be used as the limestone slurry pump, gypsum discharge pump, filter liquid feeding pump, an absorption tower circulating pump, recycling pump etc. DT Desulfurization Pump
Product name: Gravel Pump01 Model: SG (or GH) Type Gravel Pump Application: Product overview SG (or GH) type gravel pump is mainly used for the continuous conveying granular too big material strong abrasive slurry pump can transport the general. Suitable for dredger dredging, dredging, mining and metal smelting blast slag conveying etc.. The GH type gravel pump for high lift. The pump adopts a single shell pump structure connected to the cassette, the flow passage spacious. The over-current components using Ni - hard, high chromium wear-resistant materials. Pump outlet direction can be in any one of 360 degrees, with convenient installation and use, the cavitation performance, has the advantages of anti abrasion etc. Gravel Pump01
Product name: PN Mud Pump Model: PN Mud Pump Application: can be used for transporting solid-liquid two-phase fluid with mine Product overview Mud pump is a Horizontal single-stage single suction cantilever centrifugal slurry pump, can be used for transporting solid-liquid two-phase fluid with mine. Can also be used in building materials, paper, food, feed and other departments to transport all kinds of slurry. The maximum transmission, concentration of 50-60% (weight) Flow manufacturing using wear-resistant alloy material PN type slurry pump, long life. 6 "and 6" mud sand below the impeller and the shaft is connected with the screw, 8 "and 8" above the mud pump used in key connection. The gap between the blade and sheath and the impeller can be adjusted, to maintain efficient work. 8 "and 8" above the mud pump, the pump body is large, using open structure form level, the disassembly and the maintenance are convenient. Shaft seal packing seal used in general, work to win into higher than operating pressure of 1 kg / square cm shaft seal water. Model PN mud pump, according to the transmission direction, rotates in counterclockwise direction (including 1, 2, 3PN clockwise) Ye Lun with a screw connected with the shaft, if the rotating in opposite directions, Ye Lun will fall off from the shaft, causing the accident. PN Mud Pump
The Edwards 80 E2M80 direct drive rotary vane pump is inherently compact and vibration free with an ultimate pressure of 7.7x10-4 Torr and a pumping speed of 53 CFM at 60 Hz.
Product name: Flue Gas Desulfurization Pump Model: Flue Gas Desulfurization Pump Application: FGD pumps are sailed Pump Company in LC-T series slurry pump, the successful design manufactured on the basis of experience, in view of industrial flue gas Product overview Flue gas desulfurization pump Overview: FGD pumps are sailed Pump Company in LC-T series slurry pump, the successful design manufactured on the basis of experience, in view of industrial flue gas desulfurization pump characteristics, absorb with similar products within and outside the advanced technology, well-developed The new generation of series desulfurization pumps. Dedicated to the absorption tower circulating pump PH: 2.5 to 13 chlorine ion concentration: ¹60000ppm weight concentration:¹60% Medium temperature: ¹100C. Absorber circulation pump is large FGD key equipment, means there is high demand for its reliability and service life. FGD means more than half of the power consumed for driving the absorber circulation pump. Therefore, the circulating pump should have a high efficiency. Hydraulic design of the pump design and selection of materials flow components directly related to the efficiency of the pump operation, reliability and service life. We developed the absorber circulation pump, pump, pump cover over-current parts are made of 2605N material, impeller, wear plate is used Cr30A material. Hydraulic design of the pump, drawing the French company J S phase flow pump design and manufacturing technology, and the use of modern CAD, CFD technical correction. Second, the flue gas desulfurization pumps structural features: (1) The pump is single-stage single-suction centrifugal pumps, which form in practice has proved to be particularly suitable for FGD absorber circulation pumping device abrasive, corrosive slurry. (2) The impeller, wear plate without using mouth ring seal in the form, set the port ring will be slurry rapid wear, leading to the rapid decline in the efficiency of the pump. (3) having an axial adjustment structure, the impeller can be easily adjusted to maintain an axial gap between the impeller and the wear plate and the front cover, so as to maintain the high efficiency of the pump. It is always easiest to maintain and the most effective and efficient way to pump operation. (4) is arranged in the form of pump is "pull" structure. This allows the pump impeller during disassembly, mechanical seals and shaft assembly without removing the inlet and outlet pipes. (5) bearing with thin oil lubrication. Bearing mounted on a rubber ring secondary seal removable bearing box, to prevent dirt and water from entering. (6) The shaft is a large diameter, short axis head can reduce shaft deflection at work, thus extending seal life. Third, the flue gas desulfurization pump design advantages: Overview: back pull-out design of the entire rotor assembly can be pulled from the motor, easy to maintain, the pump can remain in the pipeline, without removing the motor. 1. Front pull-out design wear plates, impellers, mechanical seal can be disassembled inlet end 2. bearing bracket can be adjusted to improve the wear resistance 3. The bearing lubrication oil immersion 4. Pump: pump pressure and wear of sufficient size, materials used 2605N, weldable, volute tongue wear some special treatment, tangential flow channel outlet, the body set foot supporting way. 5. Wear plates: the part is mounted between the pump and imported materials Cr30A, this material has excellent resistance to abrasion and erosion resistance, overall performance, thereby extending the life of the pump and impeller. 6. Impeller: material Cr30A, not welded, taking into account the long run is more economical, since the bearing holder can be adjusted when the situation abrasive wheel, the wheel can be re-processed and prolong life. Front blade structure prevents large particles rushed impeller and wear plate gap, the leading blade and wear plate gap, reducing the media (in impeller and wear plate) flow rate, reducing wear, special blades wear process design, back blade design, reduced axial force, but also to block large particles, high pressure bearing design (simulation without axial force hydraulic model back under the blade), the 7. impeller vent design, can be discharged within the gaseous medium, to prevent dry running mechanical seals. 8. After the pump cover: materials used 2605N, weldable, wear usually occurs in the back of the blade area, the pump head is mounted on the bearing bracket, release stress and allow greater wear and prolong the service life of the pump cover bolts fixed bearing frame for easy disassembly without the card and damage to the pump when dismantling the mechanical seal. 9. A bearing body: the bearing body consists of two parts, the carrier and the bearing housing, the bearing housing and the adjusting screw can be adjusted by means of bolts, move horizontally within the carriage. This has the advantage: in the bearing housing to move the carriage (reprocessing size according impeller), but the inner and outer bearing ring without relative displacement, since no relative displacement, seals fully functional. When removing the lower part of the reservation on the base for easy removal, position accuracy, the installation will not occur mutual jamming of parts. 10. Mechanical seal: The mechanical seal is designed to Single seal cartridge structure, easy disassembly. Wash design there are two options: one, loaded wash water pipe fixed wash water; of the two, without a fixed wash water line, segmental wash. In the mechanical seal the work area, if the medium containing gas, mechanical seals would run dry, so the impeller is designed with vents, you can avoid large, dirty particle contact mechanical seal. Easy emptying drainage pump seal cavity volume, full lubrication, cooling sufficiently. Flue Gas Desulfurization Pump
Product name: Gravel Pump02 Model: SG (or GH) Type Gravel Pump Application: used for the continuous conveying granular too big material strong abrasive slurry pump can transport the general Product overview SG (or GH) type gravel pump is mainly used for the continuous conveying granular too big material strong abrasive slurry pump can transport the general. Suitable for dredger dredging, dredging, mining and metal smelting blast slag conveying etc.. The GH type gravel pump for high lift. The pump adopts a single shell pump structure connected to the cassette, the flow passage spacious. The over-current components using Ni - hard, high chromium wear-resistant materials. Pump outlet direction can be in any one of 360 degrees, with convenient installation and use, the cavitation performance, has the advantages of anti abrasion etc. Gravel Pump02
Pmdc motor 0.5hp 180vdc 1500 rpm flange mount frame-71, 'f' class insulation Box
komatsu PC200-7 hydralic pump 708-2L-00300,komatsu excavtaor spare parts Komatsu parts,Excavator Parts For Komatsu,Caterpillar D4dd6hd7gd6d155komatsu excavator spare parts Fast delivery. genuine and new pump
Part No : VP0.5A-4A Valtage : 220V/50Hz,110V/60Hz Capacity : 1-9.6CFM Vacuum : 30/225 pa/microns Motor Power :1/6-3/4hp Motor speed : 1440/1720rpm Intake Fitting : 1/4 SAE
Www.Hanhe-pump.Com China hanhe is a professional slurry pump, gravel pump and dredging pump manufacturer in china. Pumps are dimensional interchangeable with warman pump. 1.5/1b-ah, 3/2c-ah, 4/3c-ah, 10/8st-ah
Www.Hanhe-pump.Com Hanhe group co., limited Professional slurry pump dredging pump manufacturer and exporter china. Our slurry pump are dimensionally interchangeable with warman® slurry pump. Ah, hh, l, m slurry pump, g gravel pump and wn dredging pump. Warman ah, warman hh, warman l, warman m
Www.Hanhe-pump.Com Thg series pumps are designed to handle high abrasive slurry which contain large particles that other models pumps could not handel.The large volume inside is the best choice for gravel and dredging work.Low npsh requirement and robust design insure long life with sever duties. Warman g gravel pump
1.Oem komatsu part no.:705-56-34180 2.Model no.:wa380-1 3.Warranty:one year 4.Material:aluminium 5.Factory price 6.Displacement:sar80+56+36+12 Weight:about 53kg Standard export wooden cases
Execution standard Iso2858 "end-suction centrifugal pump, adesignation, nominal duty point and dimensions". Iso5199 "technical specifications for centrifugal pumps, aclass ¡é¨°". Performance Caliber: dn=25, , 250mm Capacity: q=5~2000m3/h Head: h=2.5~150m Speed: n=2950r/min, 1475 r/min Temperature: t= -4 Maximal design pressure: pmax=16bar
Execution standard Api610. Performance Caliber: 25~400mm Capacity: q=2.5~2600m3/h Head: h=16 ~ 250m Speed: n=2950r/min, 1475r/min Temperature range: t=-80 Maximal design pressure: sza/szao pmax=25bar; sze pmax=50bar
Execution standard Api681 "liquid ring vacuum pump and compressor" Din28431 "acceptance specifications for liquid ring vacuum pumps". Performance Caliber: dn=125, 500mm Sucking capacity¡êoq=600, 31000m3/h Suction pressure: p=33, 1013 mbar
