Which mainly use for burning the pig residual hair,the detail data as following: 1)- Material:Stainless steel 2)- Technical parameters: Work pressure: 0.3-0.5 MPA Liquefied gas Consumption: 0.3-0.5 KG / Pig Capacity:300-400 pigs /hr Out size: 2300 1500 4300mm Weight:1800KG
4-PASS Thermic Fluid Heater
The Drying Oven exterior is a general purpose laboratory used such as soil, concrete, asphalt and aggregate. Internal frame made of stainless steel sheet and external casing coated with hard wearing paint & insulated with thick mineral wool. Heat generated by high precision digital controller & temperature range from RT + 10.C to 300.C. All capacity come with fan circulation blower. The oven come with glass viewing door surrounding casing is obtained with 50 mm thick fiber glass & steel shelves.
3-PASS FULLY WET BACK STEAM BOILER Thermal-Max Steam Boiler Smoke tube type system boiler with three pass fully wet back design, suitable for cal / agro waste / oil / gas fuel. Salient Features: Factory-assembled horizontal package boiler. Less site work & quick commissioning Suitable for coal, wood & briquetted fuel. Manual firing - less complexity. Large integral furnace - minimum heat loss. High turn-down ration. End to end visibility of tubes. Easy access for inspection & cleaning. Quick and easy ash removal. Low excess air burners, imported / indigenous. Capacity:Oil Fired - 500 kg./hr. to 8000 kg./hr. Solid Fuel Fired - 500 kg./hr. to 6000 kg./hr. Pressure:10 kg./cm2 to 35kg./cm2
Fully Automatioc Coil Type Boiler Fully automatic, instant steam generating range of boilers designed for safe and reliable operations. Easy to install and commission, these time-tested boilers require very little maintenance. It features a specially designed furnace and combustion system to burn difficult heavy oils and offers fuel flexibility between light and heavy oils to help respond to fluctuating fuel prices. Salient Features: High Efficiency. Large Steam & Water Volumes. Less Maintenance Unique patented membrane design Built-in heat recovery device Membrane design allows large tube diameter for coil enabling better steam dryness, less frequent de-scaling, longer coil life and minimum downtime Unique economiser - optimiser design ensures maximum heat recovery without possibility of feed water pump failure due to boiling/ vapour causing cavitations and pump failure Unique circulation burner design prevents leakage and eliminates fire hazard Ceramic wool refractory allows fast cooling of top plate and easy maintenance Easy access to all parts requiring maintenance. Capacity:500 kg./hr. to 850 kg./hr. Pressure:10 kg/cm2 to 20kg/cm2 Fuel:Coal / Wood / Lignite / Petcock
Our steam pressure reducing station are pre-fabricated manufactured ready to install units for steam system management. The pre-assembled steam pressure reducing stations are individually sized to meet end-user's specific needs. lnlet and outlet piping & valve are sized as per best engineering practices. Each unit is custom engineered and designed to meet specific system requirements. All upstream & down stream pipe work & fittings are adequately sized to ensure that only the required pressure drop occurs across the control valve itself.
This is basically A heat transfer equipment to heat air prior to entering in the furnace with a primary object to increase thermal efficiency of hot flue gases are passed through the tubes and air outside the tubes. The heat of the boiler flue gas is recovered in APH to increase the air temperature & the thermal efficiency is increased. Another advantage is that the flue gas is sent to chimney stack at lower temperature allowing simplified design of ducting & flue gas stack. It also allow controls the temperature of flue gas leaving the stack to meet emissions regulation / pollution control. Salient Features: Easy installation Low maintenance cost Robust construction Compact High efficiency
Industrial Hot Water Generators are vented systems provide temperatures up to 98°C. Pressurized systems are essentially closed loop required for indirect heating and provide temperatures up to 150°C without boiling or steam formation. The system is suitable to heat water up to 250°C with combustion of any solid fuels like wood, coal, bagasse, corn cobs, agrowaste, lignite, petcoke, etc. System is designed with all safeties & controls well defined for safe operation without lesser maintenance. Salient Features: Heat transfer efficiency Long thermic fluid life Corrosion free No scale problems No boiler regulation High temperature Abrasion resistant Easy to use Capacity:600,000 to 10,000,000 kcal/hr. Temperature:upto 200°C Fuel:Coal / Wood / Lignite / Paddy Husk / Petcock / Saw Dust / Bagasse / etc
A unique design of the pre-furnace consists of lateral wall made of finned tube connected to the boiler body through headers. Salient Features: Complete gas-tight construction. Greater absorption of radiant heat. Fast water circulation resulting in accelerated start up and better boiler response to load fluctuations. Designed to give full load efficiency upto 80%. Optional FBC System for Capacity above 5000 kg./hr. for Automatic Firing. Capacity:1000 kg./hr. to 15000 kg./hr. Pressure:10kg./cm2 to 35 kg./cm2 Fuel:Coal / Wood / Lignite / Paddy Husk / Petcock / Saw Dust / Bagasse / Palm Oil Extracts / etc.
3-PASS FULLY WET BACK STEAM BOILER Thermal-Max Steam Boiler Smoke tube type system boiler with three pass fully wet back design, suitable for cal / agro waste / oil / gas fuel. Salient Features: Factory-assembled horizontal package boiler. Less site work & quick commissioning Suitable for coal, wood & briquetted fuel. Manual firing - less complexity. Large integral furnace - minimum heat loss. High turn-down ration. End to end visibility of tubes. Easy access for inspection & cleaning. Quick and easy ash removal. Low excess air burners, imported / indigenous. Capacity:Oil Fired - 500 kg./hr. to 8000 kg./hr. Solid Fuel Fired - 500 kg./hr. to 6000 kg./hr. Pressure:10 kg./cm2 to 35kg./cm2
Features: Mostly fixed hearth Diesel, LPG, natural gas, electrical Complete plant for hardening tempering offered Loading quenching unloading by fork attached to overhead crane Quenching in 20-30 seconds as per arrangement PLC controlled movement swift accurate time Bound Strong agitation by quenchant recirculation jet splash on hot load eliminates vapor blanketing cooling rate 800 degree C per minute Quenchant cooled by plate type heat exchanger using cold water from cooling tower Forced draft fan cooling for normalizing
Capacity:- 1 T/hr to 5 T/hr. Fuels:- Electrical, Gas, Diesel, Dual. Drier, Hardening, Quenching, Tempering Continuous Lines. Shots, Sizes, Capacities, Materials etc all are PLC programmed. High Heat temperature Grade, Long life Retorts centrifugally Cast. Ceramic Fibre lining, seal tight. Loading/Discharging End Caps. Recuperator for Heat Recovery.
Muffle Furnace
Heaters for glass tempering furnace. Heaters of Northglass furnace 7kw,14kw.
Mesh Belt Type Furnace is designed to load the product on the mesh belt and make continuous production. It is used in various processes, including plastic working, firing, drying and degreasing, for a variety of production. Using the muffle, Mesh Belt Furnace offers stable ambient control, rapid heat-up time and radiating energy saving. It is designed to implement continuity of automated production system and uniform production based on ambient per zone and temperature control.
Pusher Furnace, a representative equipment in the firing process, is designed to push the conveyor using the pusher to move the product. It is used for the firing process of various types of products and it shows excellent heat resistance, insulation efficiency and wear resistance against the conveyor. Designed as a tunnel type, Pusher Furnace implements continuity of automated production system and uniform production based on ambient per zone and temperature control.
Batch Type Furnace can be comprised of several types, such as rack, roller or elevator, and pre-process product input and post-process product output is made in 1 cycle. Batch Furnace is used for plastic working, firing, drying and degreasing of various products. Unlike the continuous furnace, it can be installed in an independent location, with advantages of convenient layout and excellent price competitiveness.
Roller Hearth Kiln is a furnace that loads the product on the roller and make continuous production. It is used in various processes, including plastic working, firing, drying and degreasing, for a variety of production. It is designed to implement continuity of automated production system and show excellence in speed variation by roller running per zone and rapid heat-up capability.
Electrode Polishing Machine for electric arc furnaces (EAF)-China Dalian BeiMeng Technology Co., Ltd. is a high-tech company specializing in the production of automation equipment, providing turn-key projects for carbon processing, automotive, electronics and cold chain industry. The company covers an area of 5000 square meters, with 30 employees and more than 20 sets of various processing equipment. In 2014, we developed the first Carbon Electrode Handling and Cleaning machine, which changed the traditional graphite electrode grinding and cleaning method, and helped carbon processing enterprises to improve work efficiency and reduce labor costs. At present, our electrode cleaning equipment has been used in several domestic leading carbon enterprises, such as Fangda Carbon, Dongfang Carbon, and Wanji Holding group. After 5 years of continuous innovation, we launched a new graphite electrode automatic cleaning production line in 2019. Compared with the original equipment, the new equipment has better stability and processing effect of finished products. Now we have obtained the patent certificate. Products: Carbon Electrode Handling and Cleaning Systems, Anodes/Carbon Butts Cleaner Machine, Carbon Anode cleaning machine, Carbon Anode Polishing Machine, Carbon bar Polishing Machine.
Carbon Electrode Cleaning for electric arc furnaces (EAF)-China Dalian BeiMeng Technology Co., Ltd. is a high-tech company specializing in the production of automation equipment, providing turn-key projects for carbon processing, automotive, electronics and cold chain industry. The company covers an area of 5000 square meters, with 30 employees and more than 20 sets of various processing equipment. In 2014, we developed the first Carbon Electrode Handling and Cleaning machine, which changed the traditional graphite electrode grinding and cleaning method, and helped carbon processing enterprises to improve work efficiency and reduce labor costs. At present, our electrode cleaning equipment has been used in several domestic leading carbon enterprises, such as Fangda Carbon, Dongfang Carbon, and Wanji Holding group. After 5 years of continuous innovation, we launched a new graphite electrode automatic cleaning production line in 2019. Compared with the original equipment, the new equipment has better stability and processing effect of finished products. Now we have obtained the patent certificate. Products: Carbon Electrode Handling and Cleaning Systems, Anodes/Carbon Butts Cleaner Machine, Carbon Anode cleaning machine, Carbon Anode Polishing Machine, Carbon bar Polishing Machine.
