3-PASS FULLY WET BACK STEAM BOILER
Thermal-Max Steam Boiler
Smoke tube type system boiler with three pass fully wet back design, suitable for cal / agro waste / oil / gas fuel.
Salient Features:
Factory-assembled horizontal package boiler.
Less site work & quick commissioning
Suitable for coal, wood & briquetted fuel.
Manual firing - less complexity.
Large integral furnace - minimum heat loss.
High turn-down ration.
End to end visibility of tubes.
Easy access for inspection & cleaning.
Quick and easy ash removal.
Low excess air burners, imported / indigenous.
Capacity:Oil Fired - 500 kg./hr. to 8000 kg./hr.
Solid Fuel Fired - 500 kg./hr. to 6000 kg./hr.
Pressure:10 kg./cm2 to 35kg./cm2
3-PASS FULLY WET BACK STEAM BOILER Thermal-Max Steam Boiler Smoke tube type system boiler with three pass fully wet back design, suitable for cal / agro waste / oil / gas fuel. Salient Features: Factory-assembled horizontal package boiler. Less site work & quick commissioning Suitable for coal, wood & briquetted fuel. Manual firing - less complexity. Large integral furnace - minimum heat loss. High turn-down ration. End to end visibility of tubes. Easy access for inspection & cleaning. Quick and easy ash removal. Low excess air burners, imported / indigenous. Capacity:Oil Fired - 500 kg./hr. to 8000 kg./hr. Solid Fuel Fired - 500 kg./hr. to 6000 kg./hr. Pressure:10 kg./cm2 to 35kg./cm2
Pvb-010 steel back self-lubricating bush (du bushing) Structure: 1.Ptfe/pb mixture 0.01~0.03mm as sliding layer, provides an excellent initial transfer film, which effectively coats the mating surface of the bearing assembly, forming homogeneous oxide type solid lubricant film. 2.Porous bronze 0.2~0.3mm, provides max. Thermal conductivity away from the bearing surface, also serves as a reservoir for the ptfe-lead mixture. 3.Low-carbon steel backing 0.7~2.3mm, provides fundamental structural support and gives exceptionally high load carrying capacity, excellent heat dissipation. 4.Tin-plating 0.005mm or copper plating 0.008mm, provides good corrosion resistance. Characteristics: Good wear and friction performance over a wide range of loads, speeds and temperature without oil Also perform well with lubrication Maintenance-free, long life Availability: Standard cylindrical bushing, flanged bush, thrust washers and strips are availabe Lead free type is also available All special designs are produced according to your requirement Applications: Lifting equipment, hydraulics and valves, pneumatic equipment, medical equipment, textile machinery, agricultural equipment, construction equipment, meterial handing equipment, packaging equipment, automotive field, scientific equipment, drying ovens, office equipment, etc.
Magnetoresistive Effect technology Ranges from 0~25Pa at up to 3KPa Three selectable ranges for each model Insensitive to media, compared to transmitters using a piezoresistive silicon or capacitance sensor Excellent stability Available with Unidirectional and bidirectional ranges, and air velocity Optional LCD display Service: Air and non-combustible gases, compatible gases Accuracy: ¡À1.0% F.S. (0.1"w.c. & 25Pa: ¡À2.0%) Range: 0- 25Pa (min.), 0-1.25KPa(max.) Thermal effects: Zero/span shift 0.05% F.S. /¡æ Pressure limits: 1psi max. operation; 10psi burst. Power supply: 10-35 VDC (2-wire); 17-36 VDC or isolated 15-26 VAC (3-wire). Output signal: 4-20mA(2-wire), 0-5V(3-wire);0-10V(3-wire) Response time: 0.5-15s adjustable. Work temperature: -10 to 50¡æ Loop resistance: Current output: 0-1250¦¸ max.; Voltage output: 1000¦¸ min. load Housing material: ABS plastic. Display (optional): 2-line, 4-digit LCD. Stability: ¡À1 %F.S./YR. Accessory: Cable gland for 4-7.5mm diameter cable Process connections: 3/16" (5mm) ID tubing; max. OD 9mm. Enclosure rating: IP65. Mounting orientation: Vertical. 10*8*5CM.
Sx2-1-12tp muffle furnace of xinyoo Chamber size100*100*100mm power1kw max. voltageAc 220v single phase, 50/60 hz max. Temperature Built in protection for over-heated and broken thermal couple. Larger digital control panel (48 x 96 mm) for easy operation. Dimension, 570 x 525 x 890 mm Gross weight, 68 kg
Cork roll Feature: 1) thickness:1 - 8mm 2) width : 1, 300mm (max) 3)length:10-120m P.S:customer size are welcome. 4) applications: A) interior material for houses B) shoe soles, underlayment, memo board, laminate floor underlayment C) thermal insulation material D) soundproof cork insulation O
Polishing abrasive white carborundum powder White carborundum powder was made from the high quality alumina by melting above 2000 in the electric arc furnace and cooling.It is white with the main crystal phase alpha-Al2O3.The white alumina produced in titling electric arc furnace has the advantage of high bulk density and low porosity and the volume stability and thermal shock resistance can be improved. Physical Index color white Mohs Hardness 9.0 Melting point 2250 Maximum service temperature 1900 Bulk density 1.75-1.95g/cm3 Real density 1.75-1.95g/cm3 Chemical analysis Al2O3(min) 99.6% SiO2(max) 0.4% Fe2O3(max) 0.2% Na2O(max) 0.4%
green silicon carbide/green sic sand Green Silicon Carbide is made of petroleum coke and high quality silica as the main raw material, salt as the additive and smelted in the resistance furnace at high temperature.Green crystal, crisp and sharp, and has a certain thermal and electrical conductivity.The micro structure is hexagonal crystal. Abrasives models: Grain: 16#, 20#, 22#, 24#, 30#, 36#, 40#, 46#, 54#, 60#, 70#, 80#, 90#, 100#, 120#, 150#, 180#, 220#, 240# Micro powder: (FEPA) F230 F240 F280 F320 F360 F400 F500 F600 F800 F1000 F1200 F1500 (JIS)240#, 280#, 320#, 360#, 400#, 500#, 600#, 4700#, 800#, 1000#, 1200#, 1500#, 2000#, 2500#, 3000#, 4000#, 6000#, 8000#, 10000# purpose: 1. it are suitable for grinding high-speed,high carbon steel 2.high-grade refractory materials 3.abrasives tool 4.grinding and polishing 5.ceramics 6.sandblasting Chemical analysis: SIC(min) 99.05% SiO2(max) 0.2% F.Si(max) 0.03% F.C(max) 0.04% Fe2O3(max) 0.1% Physical characteristics: color green Nup hardness 2600 Mohs Hardness 9.4 Melting point 2600 Specific gravity 3.2g/cm3
green sic/green carborundum powder Green Silicon Carbide is made of petroleum coke and high quality silica as the main raw material, salt as the additive and smelted in the resistance furnace at high temperature.Green crystal, crisp and sharp, and has a certain thermal and electrical conductivity.The micro structure is hexagonal crystal. Abrasives models: Grain: 16#, 20#, 22#, 24#, 30#, 36#, 40#, 46#, 54#, 60#, 70#, 80#, 90#, 100#, 120#, 150#, 180#, 220#, 240# Micro powder: (FEPA) F230 F240 F280 F320 F360 F400 F500 F600 F800 F1000 F1200 F1500 (JIS)240#, 280#, 320#, 360#, 400#, 500#, 600#, 4700#, 800#, 1000#, 1200#, 1500#, 2000#, 2500#, 3000#, 4000#, 6000#, 8000#, 10000# purpose: 1. it are suitable for grinding high-speed,high carbon steel 2.high-grade refractory materials 3.abrasives tool 4.grinding and polishing 5.ceramics 6.sandblasting Chemical analysis: SIC(min) 99.05% SiO2(max) 0.2% F.Si(max) 0.03% F.C(max) 0.04% Fe2O3(max) 0.1% Physical characteristics: color green Nup hardness 2600 Mohs Hardness 9.4 Melting point 2600 Specific gravity 3.2g/cm3
SiC Green silicon carbide powder price Green Silicon Carbide is made of petroleum coke and high quality silica as the main raw material, salt as the additive and smelted in the resistance furnace at high temperature.Green crystal, crisp and sharp, and has a certain thermal and electrical conductivity.The micro structure is hexagonal crystal. Abrasives models: Grain: 16#, 20#, 22#, 24#, 30#, 36#, 40#, 46#, 54#, 60#, 70#, 80#, 90#, 100#, 120#, 150#, 180#, 220#, 240# Micro powder: (FEPA) F230 F240 F280 F320 F360 F400 F500 F600 F800 F1000 F1200 F1500 (JIS)240#, 280#, 320#, 360#, 400#, 500#, 600#, 4700#, 800#, 1000#, 1200#, 1500#, 2000#, 2500#, 3000#, 4000#, 6000#, 8000#, 10000# purpose: 1. it are suitable for grinding high-speed,high carbon steel 2.high-grade refractory materials 3.abrasives tool 4.grinding and polishing 5.ceramics 6.sandblasting Chemical analysis: SIC(min) 99.05% SiO2(max) 0.2% F.Si(max) 0.03% F.C(max) 0.04% Fe2O3(max) 0.1% Physical characteristics: color green Nup hardness 2600 Mohs Hardness â?¥9.4 Melting point 2600â?? Specific gravity 3.2g/cm3
