* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.
When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.
PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.
* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.
* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.
* The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites.
Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature.
Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts.
PREPARATION OF FURANE MORTAR :
Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life.
Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Product Description:
Premium quality 60x120 cm porcelain tiles ideal for both floor and wall applications. Manufactured with advanced technology for superior durability, stain resistance, and aesthetic appeal. Available in a wide range of finishes including glossy, matt, carving, and marble-look designs, suitable for modern residential and commercial spaces.
EXPORT QUALITY PRODUCT Ritver Diamond Emulsion is a water-based paint, it appears in matt finish and are excellent paints for the ceiling and kitchen and bathrooms. Excellent coverage dependent on the quality of substrate (9 to 11 sqmtrs per liters) at 30 micron thickness Paint System: Apply Primer Apply Wall Putty Apply Diamond Emulsion (choose from our color list)
Synthetic Red Oxide Primer
Ritver Synthetic Red Oxide Primer Commercial is based on Alkyd resin containing anticorrosive pigments. It is used as a primer coat for many applications especially for protecting the metals and other steel structures against corrosion and is quite versatile. It forms a firm base with good adhesion for Ritver Topcoat Enamels and Ritver Quick Drying Enamels.
Ritver Spray Paints: Superior Quality and Versatility
Ritver Spray Paints are designed to deliver quick-drying performance, ensuring crack-free and peel-resistant finishes with exceptional coverage. Suitable for a wide range of surfaces, they provide unmatched convenience and ease of application.
These high-quality spray paints empower customers to showcase their creativity, whether itâ??s for artistic projects or restoring and upgrading metal surfaces to achieve a premium, refined appearance.
Available in all standard colors, Ritver Spray Paints also offer the flexibility to create custom colors upon request, ensuring tailored solutions to meet specific needs for larger quantities.
ARP326
PLASTIC PRIMER
A transparent single component primer that promotes adhesion of subsequent coats of paint on most plastic substrates particularly those used in automotive.
PP8001SH
FIBER POLYESTER PUTTY
A fiber reinforced high-build polyester putty specially formulated to offer excellent adhesion, strength and ease of application on fiber parts, metal and steel.
Ritver is a Italian paint brand, manufactured in Dubai-UAE. Spray paint white is available in packing of 400ml/275kgs (12 in a carton) can be used on exterior/interior surface of metal, wood and concrete surfaces. It has the anti rust properties and lead free technology
RITVER spray paint is anti rust protective coating available in all Ritver color shades. Available in 400ml/275gms, 12 pieces in a carton. Ritver is a Italian technology manufactured in UAE.
The revolutionary outdoor surfaces from the collection are synonymous with high strength, elegance, and versatility. Available in three different sizes, a distinguished matt finish, and colors most apt for use outdoors, the collection remarkably compliments the exterior of your spaces and elements� outdoors.
The revolutionary outdoor surfaces from the collection are synonymous with high strength, elegance, and versatility. Available in three different sizes, a distinguished matt finish, and colors most apt for use outdoors, the collection remarkably compliments the exterior of your spaces and elements� outdoors.
The revolutionary outdoor surfaces from the collection are synonymous with high strength, elegance, and versatility. Available in three different sizes, a distinguished matt finish, and colors most apt for use outdoors, the collection remarkably compliments the exterior of your spaces and elements� outdoors.
