SG01L-5LENS
Concentrator lens SiC based UV photodiode Avirtual = 55 mm2
Properties of the SG01L-5LENS UV Photodiode
* Broadband UVA+UVB+UVC, PTB reported high chip stability, for flame detection
* Radiation sensitive area A = 55 mm2
* TO5 hermetically sealed metal housing with concentrator lens, 1 isolated pin and 1 case pin
* 10µW/cm2 peak radiation results a current of approx. 700 nA
SG01L-5LENS UV Photodiod Specifications
* Typical Responsivity at Peak Wavelength: 0.130/AW
* Wavelength of max. Spectral Responsivity: 280nm
Responsivity Range: 221 - 358nm
* Sensitive Area (chip size = 0.20 mm2): 55mm2
* Dark Current (1V reverse bias): 3.5fA
* Capacitance: 250pF
* Short Circuit (10µW/cm2 at peak): 700nA
* Temperature Coefficient: < 0.1%/K
* Operating Temperature: -55 ~ +170'C
* Storage Temperature: -55 ~ +170'C
* Soldering Temperature (3s): 260'C
* Reverse Voltage: 20V
Properties of the SG01D-5LENS UV photodiode Broadband UVA+UVB+UVC, PTB reported high chip stability, for very weak radiation Radiation sensitive area A = 11.0 mm2 TO5 hermetically sealed metal housing with concentrator lens, 1 isolated pin and 1 case pin 10uW/cm2 peak radiation results a current of approx. 350 nA
PE coil pipes and tubes for water and wire cable conduit PL231 The PE coil pipes and tubes can be used: water pipe 4 â?? 6 â?? 1-inch black coil with pressure 1.6mpa, OD 20-75mm, WT 2.3-6.8mm pe conduit cable embedded wire cable and optical cable, OD 20-200mm, WT 1.8-3.5mm weak current protection tube and communication tube, OD 20-200mm, WT 1.8-3.5mm We use new 100% pure raw PE material WHY NEW MATERIAL HDPE PIPES? 1. Health performance PE pipe processing without adding heavy metal salt stabilizer, no scaling layer, and no bacteria. 2. Corrosion resistance It can resist various chemical media erosion, with no electrochemical corrosion. 3. Service life Under rated temperature and pressure conditions, PE pipes can be used for more than 50 years. 4. Impact resistance PE pipe toughness, high impact strength, heavy objects directly pressed through the pipeline will not break. 5. Connection performance The strength of the hot melt or electric melt interface of the polyethylene HDPE pipe is higher than that of the pipe body, and the joint will not be broken due to soil movement or live load. 6. Construction performance It has a lightweight pipe weight, a simple welding process, convenient construction, and a low overall project cost.
SG01M-B5 UVB-only SiC based UV photodiode A = 0.20 mm2 Properties of the SG01M-B5 UV Photodiode * UVB-only sensitivity, PTB reported high chip stability * Active Area A = 0.20 mm2 * TO5 hermetically sealed metal housing, 1 isolated pin and 1 case pin * 10mW/cm2 peak radiation results a current of approx. 2500 nA SG01M-B5 UV Photodiode Specifications Typical Responsivity at Peak Wavelength: 0.125/AW Wavelength of max. Spectral Responsivity: 280nm Responsivity Range: 231 to 309nm Active Area: 0.20mm2 Dark Current (1V reverse bias): 0.7fA Capacitance: 50pF Short Circuit (10mW/cm2 at peak): 2500nA Temperature Coefficient: < 0.1%/K Operating Temperature: -55 ~ +170'C Storage Temperature: -55 ~ +170'C Soldering Temperature (3s): 260'C Reverse Voltage: 20V
SG01S-C18 UVC-only SiC based UV photodiode A = 0.06 mm2 Properties of the SG01S-C18 UV Photodiode * UVC-only sensitivity, compliant with DVGW W294, PTB reported high chip stability * Active Area A = 0.06 mm2 * TO18 hermetically sealed metal housing, 1 isolated pin and 1 case pin * 10mW/cm2 peak radiation results a current of approx. 720 nA SG01S-C18 UV Photodiode Specifications * Typical Responsivity at Peak Wavelength: 0,120/AW * Wavelength of max. Spectral Responsivity: 275nm * Responsivity Range: 225 - 287nm * Active Area: 0.06mm2 * Dark Current (1V reverse bias): 0.2fA * Capacitance: 15pF * Short Circuit (10mW/cm2 at peak): 720nA * Temperature Coefficient: < 0.1%/K * Operating Temperature: -55 ~ +170°C * Storage Temperature: -55 ~ +170°C * Soldering Temperature (3s): 260°C
Product Overview The ignition point of a fire inside the electric panel is mostly the part where the terminal block is fastened, so in order for initial fire extinguishing, the solution should be closely installed to the part where the terminal block is fastened. In the case of a small electric panel, a complete initial fire extinguishing is expected for fires occurring inside the electric panel by attaching the SFEX Pad to the top surface of the electric panel. Product Feature It has an excellent performance in the initial fire suppression as it can be installed near the ignition point as a flexible rope type. It uses a stand-alone method based on polymer chemistry so that it does not cause malfunctions and maintenance costs. The thermo-responsive Granule composed of KNO3 and subsidiary catalysts It does not affect the peripherals after the fire goes out. Function of SFEX Granule = fire extinguishing agent storage tank + temperature sensor + nozzle function Fire extinguishing method : Suffocation + subsidiary catalyst Example of Installation 1 : SFEX Line - If ducts exist Installing the SFEX Line horizontally or vertically in the ducts closest to the expected ignition points It can be installed without damaging the panel Example of Installation 2 : SFEX Line - If ducts do not exist Installing the SFEX Line horizontally or vertically, close to the expected ignition points of the Electric panel Example of Installation 2 : SFEX Pad - Small Electric Panel Simply attach it to the top inside the Electric panel.
Floating cable which can be applied to underwater robot equipment, either in fresh water environment or in seawater environment. It is widely used in marine exploration robot, underwater ROV UAV remote control submersible, underwater camera, underwater construction, underwater search and rescue robot, pipeline detection robot, submersible pump and the link between various underwater electrical equipment and shore based equipment; Link of signal transmission, power supply and equipment control system from underwater to water.
Electrical Characteristics - Rated Voltage : 0.6/1 kV AC - Rated DC Voltage : 1.5 kV - Maximum Permitted DC Voltage : 1.8 kV (conductor/conductor, non earthen system, circuit not under load) - Maximum Permitted AC Voltage : 1 KV - Working Voltage : DC 1000 V - Spark Test : 6000 V. ac (8400 Vdc) - Voltage Withstand : 6500 V as per EN50395 for 5 min - Ampacity : According to requirements for cables for PV systems Technical Data - Ambient Temperature : -40C +90C - Minimum Bending Radius : 5 x OD (fixed), 15 x OD (occasional flexing) - Flame retardant according to IEC 60332-1-2 - Low smoke emission < 20% as per ASTM D-2843 - Halogen free according to EN 50267-2-1/-2, IEC 60754-2 - Maximum Temperature at Conductor : 120C (20000h) - Short Circuit Temperature : 200�?�°C (at conductor max. 5sec) - Thermal Endurance Test : According to EN 60216-2 (temperature index +120C) - High Temperature Pressure : Test according to EN 60811-3-1 - Excellent mechanical and electrical properties. - UV resistance & OZONE resistance - Flexibility & suitability for fast & easy installation Cable Standard EN 50618 Standard Packing Coils 100, 200,300, 500, 1000m Conductor Flexible Electrolytic fine Tinned copper class-5 conductor according to IEC 60228 Insulation XLPO (Crosslinked Halogen Free & Flame Retardant) Sheath XLPO (Crosslinked Halogen Free & Flame Retardant) Color Red, Black and also available black color with red lining. Application For Solar Panel, Solar Power Plant, Solar Pump Installation.
The skid-mate is an air dampened cushioning device that provides a fast, cost effectiveand durable customized solution to protect sensitive products from shock and vibration. Theskid-mate can be easily mounted on a crate or pallet base creating an air-ride cushion in placeof hardwood skid runners eliminating the need for expensive air-ride trucks.Each color coded skid-mate corresponds to a specific load range and allows users to calculatetheir requirements simply and easily to avoid potential laboratory testing and use of expensivepackaging materials. Reduce packaging design & assembly time and cost• eliminate costly damage from handling hazards during shipment• reduce costs associated with shock and vibration damage
Cable Standard Generally conforms to, Based on IS:9857-1990 VDE 0282, IEC 245-6, BS 6899 Silent Features - Ultra high performance flexible welding lead, double insulated for longer life and added safety - Better flame retardant properties - Outstanding toughness & durability - High resistance to cuts, tears & abrasion - Resistance to oil, solvents and chemicals - Excellent ozone and weather resistant Technical Data Fixed Installation : -20C to max.+90C Nominal Voltage : 600 V Spark Test : 3.5 KV(ac) Color : Orange / Black Jacket Min. Bending Radius : 6 x Cable Diameter Standard Packing Coils 100, 200, 300 and 500m Conductor High conductivity, bare annealed copper flexible conductor, EC copper class 5 & class 6 generally conforms to IS:8130-1984, IEC 60228 Separation Polyester tape Insulation Double Insulated/single insulated flexible Nitrile rubber HOFR insulated as per IS:6380-1984 Color Orange / Black Jacket Current Rating The maximum current ratings of flexible welding cables for different duly cycles are based on an ambient air temperature of 25 C and a maximum conductor temperature of 90 C. The percentage duly cycles for various processes and applications are as follows: - Automobile Welding : up to 100% - Semi Automatic Welding : 30% to 85% - Manual Welding : 0% to 60% - Very intermittent or Occasional Welding : up to 20% Voltage Drop When total cable lengths in excess of 15mtr., are involved, it may be necessary to use cables of larger cross section to ensure that the voltage drop is not excessive & welding currents are maintained at adequate levels. Application Designed for the secondary (high current) connection to automatic or hand - held metal arc welding electrodes. It is suitable for flexible use under rugged conditions, on assembly lines & conveyor systems, in machine tool and automatically operated line & spot welding machines