Rotating Paddle Switch

It has outstanding features such as good sealing, strong overload capacity, lightweight and easy to installation, large output contacts capacity, etc. In view of the different sensibility of material can be done by adjustable tension of the spring, contact material part of its full stainless steel material. Resistance rotary switch in the chemical, plastic, cement, medicine, feed, food and other industries widely used.

We are engaged in offering Stirrup Bending Machine, which is extremely praised in the market. Owing to high demand, professionals make these products in varied patterns. MODEL ZAR 20D Type Automatic TMT bar Steel Bar Dia 4-20 mm Motor Power 2.2KW Angle feed ZAR20 Manual & 20D Auto Preset Angle 9 / 135 Paddles 2nos. Motor Rotation 1440 r/min Voltage 415v Weight 320 Kg.

Main Application: As a whole stainless horizontal tank type mixer, this machine is widely used for mixing of powdery or paste material in pharmaceutical chemical and foodstuff industries. Working Principle: S type agitiating paddle is rotated, through mechanical driving, which pushes the material turn repeatedly and mix uniformly. Operate with electrical control, it can set mixing time to realize automatic stop and electric discharge upon expiration, thus improving the mix quality of each batch of material and realizing the high homogeneous mixing. ITEM TYPE: CH200 Trough capacity: 200L Miaing arm speed: 24r/min tilting angle of the trough: 105 Main motor: 3KW overall dimension: 1660*700*1200mm weight: 300kg

It is mounted on square or tubular mast easily and safely. It is not used an outside sensor or mercury switch on machine because, elektronic card has sensor instead of them. It is not impressed by wind , impulse or pulsation. It starts rotating at 10º angle automatically and stops after balancing. If tail jam occurs, brush will rotate reverse direction. Type , density and hardness of brush is selected most properly and revolution per minute of reducer is selected most properly too.With the result that;cow comfort, health, welfare and overall performance is increased. Rotating speed:30 rpm Brush length:70 cm Brush diameter:47 cm Power:0, 18kw Electronic angle measurement.

The range of No. 0 spindles: 1-100 cp The range of No. 1, 2, 3, 4 spindles: 101-2000000 cp With Rs232C and temperature sensor Model : RV-2T Model RV-2T Measurement Range 1-2000000 mpa.s Display LCD Spindles Specification No. 0, 1, 2, 3, 4 Note: The bigger the number of the Spindles, the bigger the measuring value Rotating Speed of Spindles 0.3 / 0.6 / 0.5 / 3 / 6 / 12 / 30 / 60 rpm Automatic Switch free selection of proper rotating speed or Spindles number. Stable Cursor Strip-type cursor fully charged displayed when reading basically stable Measurement Tolerance ± 2% Power AC 220V ± 10%  50 Hz ± 10% Working Condition Temperature 5-35 degree Relative humidity no more than 80%

china coal0001 HMR100 Vibratory Concrete Finishing Tools Machine Introduction of HMR100 Vibratory Concrete Finishing Tools Machine HMR100 Vibratory Concrete Finishing Tools Machine with CE is widely used in surface of concrete raised paste and trowel and smooth out in high-standard workshop, warehouse, parking lot, square, airport and frame-style building. The efficiency of Concrete Power Trowel Machine is 10 times higher than the manual work. The max rev is up to 120r.p.m. Features of HMR100 Vibratory Concrete Finishing Tools Machine 1. Heavy-duty gearbox, excellent performance and durability. 2. Emergency switch can automatically cut engine power, to ensure operator safety. 3. Armrest can be adjusted to accommodate different height of the operator. 4.Balanced blade design makes the machine more stable. Parameter of HMR100 Vibratory Concrete Finishing Tools Machine ModelHMR100 EngineHonda GX160, Robin EY20, Lifan 168F Engine typeAir-cooled, Single cylinder, Four stroke Engine Engine power5.0-5.5HP Working diameter960mm Rotation speed of blade70-130rpm Package size (mm)1120*1120*800 Net weight93kgs

The range of No. 0 spindles: 1-100 cp The range of No. 1, 2, 3, 4 spindles: 101-2000000 cp Model : RV-2M Model RV-2M Measurement Range 1-2 106 mpa.s Display LCD Spindles Specification No. 0, 1, 2, 3, 4 Note: The bigger the number of the Spindles, the bigger the measuring value Rotating Speed of Spindles 0.3 / 0.6 / 1.5 / 3 / 6 / 12 / 30 / 60 rpm/min. Interface Optional (RS232C, temperature probe, edit software CD) Automatic Switch free selection of proper rotating speed or spindles number. Stable Cursor Strip-type cursor fully charged displayed when reading basically stable Measurement Tolerance ± 2% Power AC 220V ± 10%  50 Hz ± 10% Working Condition Temperature 5-35 degree Relative humidity no more than 80% Outline Dimension (mm) 370 325-280 mm Packing (mm) 400 360 310 mm Net Weight (kg) 6.8 kg Gross Weight (kg) 9 kg Attachments l         No. 1,2,3,4 Spindles    No. 0 Spindle   Adapter Protection Frame Foundation Plate Up-Down Frame English Manual Hexagonal Spanner Solid Wrench

Glue spreader is used for spreading glue Uniformly on veneers. Uniform gluing with the exact figure of adhesives improves the quality of plywood and saves a huge amount of expense in the long run. The clearance between the glue rolls and the doctor roll, in which a stepless change in rotation is available, can be freely adjusted according to the viscosity and the amount of glue to be spread. The waste scrapes the glue roll. When it inserts to the clearance either between the glue rolls; or between the glue roll and the doctor roll, the rolls are separate quickly by air cylinder. So, the wastefall down and cannot scrape the glue roll. This Machine has VFD (Vector Frequency Drive). It can control stability of the running motor and the horse power of the output. At the operation the exchanged velocity, it can adjust easily the needed gluing velocity according to the actual gluing situation. (Nonstep speed change).Besides, this machine is specially equipped with an emergency stop switch which can immediately stop the running machine in emergency conditions. The operator can activate the emergency stop switch within a very short time to ensure the safety of the operator. Main Rubber Rolls 400 mm Dia x 2700 mm Length x 2 Sets Doctor Rolls 250 mm Dia x 2700 mm Length x 2 Sets Clearance Between Rubber Rolls 0 70 by handle. Adjustment of Doctor Rolls One Touch Controlled by Pneumatic System & Fine adjustment by handle with revolution indicator. Motor for Outfeed Conveyor 0.75 Kw (1 H.P.) with VFD. Motor for Main Roller Drives 7.5 Kw (10 H.P.) with VFD & Imported Gearbox.

1. Brief description CD1 electric hoist has only normal speed, which can satisfy the general working requirement. MD1 electric hoist has one more hoisting motor and one slow speed actuating device, which make the model have two speeds. When it works slowly, it can satisfy the precise task such as precise working of loading and unloading, sand to break-in. 2. Applications It can travel rotation through the trolley hanging on the I-steel, and install on the single beam crane, gantry crane, jib crane and overhang crane to rise and fall the cargos. So it can be used in factories, mines, wharf, warehouse, freight yards, and shops and so on which need lifting equipment for lifting heavy objects. Such as mining companies and railways, docks, warehouses. It is prohibited to manned. 3. Components Motor: Hoist Motor is an taper type rotor motor with braking,it is made by Nanjing special motor factory,it is of the best quality motors, it has bigger torque, so it can be adapted to moving frequently. Trolley: It is assembled and has running wheels. Herein, the runner wheels are mounted on top-class sealed ball bearings. Gear Box: Hoist Gear Box has specially treated gears for high wear resistance. Each Geared Shaft assembly is supported on ball or roller bearings , to ensure smooth, low-friction operation. Wire Rope: Hoisting rope comply with the exporting ISO standards. The leading rope taken by the Drum, does not slip sideways when slack. The factor of safety, on the nominal breaking strength of the rope is six. Rope Drum: Grooved Drum, seamless pipe of adequate length to be wounded in one layer and to provide proper support for the rope to minimize abrasive wear is provided. Drum Shaft resolves on Ball Bearings for ensuring smooth running. Electric control system: Model CD1 and MD1 is composed of the contactor box,controlling switch,cut-off limiter.the working voltage of controlling switch is 380V,36V or 24V(safety voltage). Rope Guide: Rope Guide is in two halves, ensuring easy accessibility. It encircles the Drum completely so that the rope may not uncoil even when the Hoist is in unloaded condition. Hook: The Hook Block is tested to 150 % of full load before assembly. The rope sheaves are fully guarded with protective steel casting . Testing: All our Hoists are tested on 125 % thus assuring safe working load and is issued with a test certificate. If you need other type electric hoist, please tell us, we will be pleased to be of further assistance!