Tobee Mission Magnum I Pumps are proven as reliable, heavy-duty, low-cost slurry pumps. The 3 2 13 through 8 6 14 pumps all feature the same power end, which ensures production and reduced spare-part inventory requirements. The Mission MAGNUM I has been engineered for the toughest jobs in drilling, production, well-servicing, and industrial applications. The MAGNUM I is more powerful, more durable, and easier to maintain than any conventional pump in use today.
The Magnum has an open impeller design that contains wide-tipped vanes and a more tangential circumference of the suction allowing the pump to create a smoother flow pattern when handling abrasive fluids. The Magnum is available in Magnachromeâ?¢, hard iron, stainless steel, and aluminum bronze fluid ends. The pumps can be unitized with electric motors, diesel engines, and hydraulic motors (horizontal, vertical, or close-coupled configuration).
Also available, Horizontal and Vertical Close Coupled Magnum.
Tobee Mission Magnum I Pumps are proven as reliable, heavy-duty, low-cost slurry pumps. The 3x2x13 through 8x6x14 pumps all feature the same power end, which ensures production and reduced spare-part inventory requirements. The Mission MAGNUM I has been engineered for the toughest jobs in drilling, production, well-servicing, and industrial applications. The MAGNUM I is more powerful, more durable, and easier to maintain than any conventional pump in use today. The Magnum has an open impeller design that contains wide-tipped vanes and a more tangential circumference of the suction allowing the pump to create a smoother flow pattern when handling abrasive fluids. The Magnum is available in Magnachrome, hard iron, stainless steel, and aluminum bronze fluid ends. The pumps can be unitized with electric motors, diesel engines, and hydraulic motors (horizontal, vertical, or close-coupled configuration). Also available, Horizontal and Vertical Close Coupled Magnum.
Sandman 8x6x11 Mission Magnum Centrifugal Sand Pump with open type impeller 19121-70-30 and hard iron casing 19763-01-30A is widely used for handle the barite, ferric oxide and mineral oil base drilling muds. MISSION Magnum I pumps are proven as reliable, heavy-duty, low-cost slurry pumps. The 3x2x13 through 8x6x14 pumps all feature the same power end, which ensures production and reduced spare-part inventory requirements. Standard models are equipped with a heavy-duty 2½-in. alloy steel shaft protected from wear by a stainless-steel shaft sleeve, double-row outboard bearings, and inboard roller bearings. They are rated for continuous service in applications up to 200 hp and are available in hard iron, stainless steel, aluminum bronze, and high Chrome with capacities up to 3,400 gal/min and pressure head up to 550 ft. Some sizes can be offered in a counterclockwise rotation giving the user more flexibility. Mission MAGNUM I Sand Pump Tobee�® as a professional centrifugal pump manufacturer in China, with more than 34 years of experience in the manufacturing and service of Mission centrifugal pumps and parts. Our pumps are specifically designed to meet the needs of some of the oil and gas drilling, mining, fluid pumping, horizontal directional drilling and well stimulation fracking. Tobee offers a complete line of centrifugal sand pumps to suit for all kinds of drilling sand pump application. Size ranges from 3x2x13, 4x3x13, 5x4x14, 6x5x11,6x5x14, 8x6x11,8x6x14, 10x8x14, 12x10x23 to 14x12x22b. Bare pumps, matching motors are available from 7.5KW to 90KW, with rotation 800, 1000, 1150,1450, 1750 to 3500 RPM at 50Hz or 60Hz. The model 10x8x14 and 8x6x14 centrifugal magnum pump used on solid control system over 3000 meter-long drilling rigs, with big viscosity and heavy specific gravity drilling fluid. 8x6x11 centrifugal mud solid control feeding pump applies to under 3000 meter-long drilling rigs, and it also can be used to supply mud to triplex mud pump as a filling pump. 6x5x11 centrifugal pump applies to truck-mounted drilling rigs or pocket drilling rigs. 4x3x13 drilling centrifugal pump is usually used as measuring pump or replenishment pump. 3x2x13 model pump is usually used as clean water pump.
Lake can supply the NOV Mission Magnum, Sandmaster and XP types centrifugal pumps, can interchange 100% with original! It is ideally suited for pumping high volumes of heavy slurries that are abrasive, corrosive. An excellent choice for high volume mobile and stationary applications where a small footprint is critical. The low stuffing box pressure can increase seal life approximately 50%. The extra-heavy shaft is designed for minimum deflection. The heavy duty bearings are permanently lubricated to minimize maintenance.
Tobee 4x3C-AH Slurry Pump with ceramic shaft sleeve C075J04 that widely used as ash handling pump in as handling system in power plant. Slurry Pump Ceramic Shaft Sleeve, which has undergone destructive field tests for over 18 months, has proved to extend part life several times that of steel shaft sleeves on the same pump, same service. Total maintenance costs and down-time were reduced accordingly. Tobee's slurry pump ceramic shaft sleeves are precision formed of high density alumina, fired, and ground to size. The hardness of ceramics (9.0 to 9.5 MOH Scale) resists this destructive action, In addition, the ceramic coated sleeve surface is highly polished which, together with its lower co-efficient of friction, results in extended sleeve life and long service from the packing. One of the problems of concern to operators of centrifugal slurry pumps is the wear of shaft sleeves and the deterioration of packing material in the gland. This matter has also been under study by the Materials Research and Development Department of TOBEE PUMP for some time. The result is the development of a shaft sleeve of much superior wearing qualities. Tobee Slurry Pump Ceramic Shaft Sleeve, which has undergone destructive field tests for over 18 months, has proved to extend part life several times that of steel shaft sleeves on the same pump, same service. Total maintenance costs and down-time were reduced accordingly. Slurry Pump Steel Shaft Sleeve has always been the here-to-fore accepted material for shaft sleeves for most centrifugal slurry pumps. However, steel in shaft sleeves is subject to pitting, fritting and wear that often results in short part life. So Tobee Pump developments of a ceramic coating shaft sleeve of much superior wearing qualities.
Tobee Mission Magnum 8x6x18, 12x10x23 and 14x12x22 Blender Pumps are ideally suited for pumping high volumes of heavy slurries that are abrasive, corrosive. An excellent choice for high volume mobile and stationary applications where a small footprint is critical. The low stuffing box pressure can increase seal life approximately 50%. The extra-heavy shaft is designed for minimum deflection. The heavy duty bearings are permanently lubricated to minimize maintenance.
Lake can supply the NOV Mission Magnum, Sandmaster and XP types centrifugal pumps, can interchange 100% with original! It is ideally suited for pumping high volumes of heavy slurries that are abrasive, corrosive. An excellent choice for high volume mobile and stationary applications where a small footprint is critical. The low stuffing box pressure can increase seal life approximately 50%. The extra-heavy shaft is designed for minimum deflection. The heavy duty bearings are permanently lubricated to minimize maintenance.
Lake can supply the NOV Mission Magnum, Sandmaster and XP types centrifugal pumps, can interchange 100% with original! It is ideally suited for pumping high volumes of heavy slurries that are abrasive, corrosive. An excellent choice for high volume mobile and stationary applications where a small footprint is critical. The low stuffing box pressure can increase seal life approximately 50%. The extra-heavy shaft is designed for minimum deflection. The heavy duty bearings are permanently lubricated to minimize maintenance. How to contact with us:
We can supply many spare parts of slurry pump. OEM pump part is welcome. Material options: -High Chrome alloy -Grey Iron -Cast Iron -Rubber -Polyurethane -OEM Pump Parts: Metal impeller is made of high chrome alloy, SA05,SA49, anti-abrasive, SA33 anti-corrosive Rubber impeller is made of SR26,SR55, SR33 Polyurethane material is available. Brief introduction: -Spare parts in anti-abrasion high chrome cast iron alloy. -Largest weight of single workpiece can be 13t. -Largest outside diameter of workpiece can be 5m -Manufacture other mechanical parts according to your drawing.
Sandman 8x6x11 Replacement NOV Mission Magnum Centrifugal Pumps with 11 inch impeller that widely used for provide drilling liquid with a certain discharge capacity and pressure to sand, desilter and mud mixer. MISSION Magnum I pumps are proven as reliable, heavy-duty, low-cost slurry pumps. The 3x2x13 through 8x6x14 pumps all feature the same power end, which ensures production and reduced spare-part inventory requirements. Standard models are equipped with a heavy-duty 2�½-in. alloy steel shaft protected from wear by a stainless-steel shaft sleeve, double-row outboard bearings, and inboard roller bearings. They are rated for continuous service in applications up to 200 hp and are available in hard iron, stainless steel, aluminum bronze, and high Chrome with capacities up to 3,400 gal/min and pressure head up to 550 ft. Some sizes can be offered in a counterclockwise rotation giving the user more flexibility. Mission MAGNUM I Sand Pump Tobee�® as a professional centrifugal pump manufacturer in China, with more than 34 years of experience in the manufacturing and service of Mission centrifugal pumps and parts. Our pumps are specifically designed to meet the needs of some of the oil and gas drilling, mining, fluid pumping, horizontal directional drilling and well stimulation fracking. Tobee offers a complete line of centrifugal sand pumps to suit for all kinds of drilling sand pump application. Size ranges from 3x2x13, 4x3x13, 5x4x14, 6x5x11,6x5x14, 8x6x11,8x6x14, 10x8x14, 12x10x23 to 14x12x22b. Bare pumps, matching motors are available from 7.5KW to 90KW, with rotation 800, 1000, 1150,1450, 1750 to 3500 RPM at 50Hz or 60Hz. The model 10x8x14 and 8x6x14 centrifugal magnum pump used on solid control system over 3000 meter-long drilling rigs, with big viscosity and heavy specific gravity drilling fluid. 8x6x11 centrifugal mud solid control feeding pump applies to under 3000 meter-long drilling rigs, and it also can be used to supply mud to triplex mud pump as a filling pump. 6x5x11 centrifugal pump applies to truck-mounted drilling rigs or pocket drilling rigs. 4x3x13 drilling centrifugal pump is usually used as measuring pump or replenishment pump. 3x2x13 model pump is usually used as clean water pump.
