Debug Tool

Short Description: Model CR606-HT The debug tool is used to read the data of Changruns full range of fuel sensors and accessories, set its function parameters and perform fault diagnosis. It can completely replace the work of the computer, and has the advantages of convenient carrying and simple operation. The debug tool can first be used to calibrate the fuel tank. It can simultaneously read the instantaneous percentage of the oil volume, the instantaneous digital value, the filtering percentage, and the filtered digital value. The liquid level status of the current device is displayed. The debug tool supports both RS232/RS485 digital signals and can set the RS232/RS485 signal listening mode (receive data only). Other functions of this product include: setting RS232/RS485 digital communication fuel volume sensor, CR606TS signal conversion module, CR606TC modem damping value, equipment ID, timing report, resistance table (CR606TC specific), debugging original car fuel meter, reading the internal parameters of the sensor and accessories. Performance Working voltage: built-in lithium battery 1000mAh 3.7V Communication method: RS232/RS485 Operating temperature: -35 ° C +70 ° C Output voltage: DC 10V Set the resistance: 4-200Ω Volume: length 109mm width 52mm height 23mm

RIFF Box 2 JTAG is the phone Unlock / Flash / Repair Tool for HTC, Samsung, Huawei. IFF Box 2 is used for reading and recovery smartphones. RIFF Box V2 is designed to accommodate a large variety of communication protocols Riff Box V2 is used to read and write memory eMMC / NAND using all kinds of communication protocols like eMMC (ISP Direct) / JTAG / I2C / SPI. Box fully supports 4-bit transmissions and allows you to read up to 52 MHz bus width. ORIGINAL RIFF Box 2 - JTAG/EMMC/I2C/GPIO, Official Website: https://www.riffbox.org/ Product Specification : Dual-core Cortex-M4 MCU @ 204MHz PC to Box USB (Device) Speed: Hi-Speed (480 Mbps) Box to Device (Host) Speed: Full-Speed (48 Mbps) SD/MMC Interface with 1-Bit (DAT0) and 4-Bit (DAT0-DAT3) Bus Width support and SD_CLK up to 52 MHz UART Interface RIFF Smart Probing Feature Level-adjustable 23 GPIO Lines (1.65V - 3.6V) for interfacing a range of devices and protocols, such as NAND, SPI, I2C, Pin Finder, etc. 4 fixed 3.3V GPIO Lines Interface Specification : 20-Pin Male Connector : JTAG Interface: TRST, TDI, TMS, TCK, RTCK, TDO and NRST Serial Wire Debug Interface: SWCLK, SWDIO (SWDIO and SWCLK are overlaid on the TMS and TCK pins) 30-Pin Male Connector : SD/MMC Interface 1/4Bit @ 52MHz Level-adjustable 23 GPIO Lines (1.65V to 3.6V) USB Device Connector : Connects the Box with PC @ Hi-Speed (480 Mbps), approx. 20 MByte/sec USB Host Connector : connects the Box with USB devices @ Full-Speed (48 Mbps), approx. 1.5-2 MByte/sec RJ-45 Connector : 6.1 RIFF Smart Probing Feature 6.2 UART Port 6.3 4 Fixed 3.3V GPIO Lines Supported SD/MMD Revisions : Revisions 1.0 to 1.7 (MMC: v4.0, v4.1, v4.2, v4.3, v4.41, v4.5, v4.51, v5.0) and higher Package List : 1 x Riff Box 2 JTAG/EMMC 2 x Conneciton tapes IDC 20 pin 1 x Connection tape IDC 30 pin 1 x Universal PCB

Processing Part: Aluminum alloy wheel hubs for car, Aluminum Alloy Outer Circle, Head Face Processing Way: Turning, Semi-Fishing, Fishing Characters: PCD Turing Tools Have Long Service Life, High Efficiency And Work Pieces Have Higher Brightness Etc. During the wheel hub machining process, uses the PCD wheel hub tool for repairing and refurbishing the aluminum alloy wheel hub rim. Applications of PCD wheel hub turning tools: The PCD wheel hub tools are used for turning and finishing aluminum alloy wheel hub rims for cars. Advantage of PCD tools for wheel hub cutting: The tool bits of the PCD wheel hub turning tools use PCD & PCBN blanks by E6. The cutter arbor uses high-quality tungsten carbide and tool steel Advanced Welding Technology To Ensure PCD turning tools No Turning, No Welding Off, No Carbonization, Long Life Welded Integral Hub Tools with Good Tool Rigidity, Good Shock Resistance, Stable Performance, And Large Feed It Is An Aluminum Car Wheel, Motorcycle Aluminum Wheel Hub, Electric Vehicle Aluminum Wheel Hub The Most Commonly Used Diamond Blade For Fine Turning. PCD wheel hub turning tools Classification: 1. Welded Integral Hub Tools.(Can Be Designed To Meet Sp ecific Customer Requirements.) The PCD blade and the tool holder are welded together, which has good thermal conductivity, stability and impact resistance. The size can be customized according to customer needs, which saves the debugging time for the matching of the blade base and the tool holder. In turn, the rapid response of the processing site is achieved. Mainly used for rough machining of wheel hubs. Common Specifications Include 25*25 And 20*20 Two Kinds Of Body Specifications, Divided Into Forehand And Backhand. ·The Dimensions Of The Cutter Head R Are Generally R4, R3, R2.5, And R2. ·The Protruding Part Of The Welding Head Of The Blade Body Is Welded With a Hard Alloy To Reinforce The Strength. ·The Extension Length Is Determined By The Processing Of The Hub Size And The Depth Of The Rim. Advantages: Good Tool Rigidity, High Welding Strength, Good Shock Resistance, Stable Performance, And Large Feed.

1.The super-high quality and mass remarkably surpass the domestic first-class factories. 2.The beam guide and ram guide are handled by supersonic frequency induction hardening (HRC�?�50) while the sliding surface of guide is treated with sticking plastic (including inclined veneers and pressure plate). The precision of the product can be maintained for a long time and the cycle for big repair can be extended as long as more than 10 years. 3.EXcellent casting comes from the same factory that the domestic big factories utilize (all are in type of HT300) and the artificial heat ageing is carried out. The casting can never be carried out with weight-reducing treatment, the weight of the whole machine accords with the standard one. 4.five-angle tool carrier adopts high-precision rat gear for positioning and for all 120 pieces, super-strong stiffness. (the traditional five piece positioning plate can be compared with it) 5. 2 axial digital display is taken as the standard confirmation (4 axial digital display type will be exported) 6.The electrics adopt Japan Omron PLC control and the electric components utilize the components with ultra-high quality , specification (CE standard) assembly process, in addition, the electrics of the whole machine owns super-high reliability. 7.ELectric rotary valve, Grade 16 machinery variable speed make the device convenient, smart and reliable. 8.High-precision gear grinding gear and gear grinding spiral bevel (Grade 6 precision) are featured with low noise and stable operation. 9.JB/T4116-96 precision test standard of vertical lathe is performed JB/3665-96 technical condition of vertical lathe is performed. 10.Advanced and perfect processing and assembly process forge excellent quality. 11.Accessory configuration is complete and only the user prepares for the knife and measuring tool, the operation can be started immediately. Perfect after-sales service (pre-sales, in-sales, after-sales, installation, debugging, training and maintenance etc.) in addition, one-year quality assurance service is granted. 12.Optional configuration: rolling working platform, Germany Mecano button station, heightening lathe and prolonging ram and square ram etc.

C5126E Single Column Vertical Lathes 1.The super-high quality and mass remarkably surpass the domestic first-class factories. 2.The beam guide and ram guide are handled by supersonic frequency induction hardening (HRC�?�50) while the sliding surface of guide is treated with sticking plastic (including inclined veneers and pressure plate). The precision of the product can be maintained for a long time and the cycle for big repair can be extended as long as more than 10 years. 3.EXcellent casting comes from the same factory that the domestic big factories utilize (all are in type of HT300) and the artificial heat ageing is carried out. The casting can never be carried out with weight-reducing treatment, the weight of the whole machine accords with the standard one. 4.five-angle tool carrier adopts high-precision rat gear for positioning and for all 120 pieces, super-strong stiffness. (the traditional five piece positioning plate can be compared with it) 5. 2 axial digital display is taken as the standard confirmation (4 axial digital display type will be exported) 6.The electrics adopt Japan Omron PLC control and the electric components utilize the components with ultra-high quality , specification (CE standard ) assembly process, in addition, the electrics of the whole machine owns super-high reliability. 7.ELectric rotary valve, Grade 16 machinery variable speed make the device convenient, smart and reliable. 8.High-precision gear grinding gear and gear grinding spiral bevel (Grade 6 precision) are featured with low noise and stable operation. 9.JB/T4116-96 precision test standard of vertical lathe is performed JB/3665-96 technical condition of vertical lathe is performed. 10.Advanced and perfect processing and assembly process forge excellent quality. 11.Accessory configuration is complete and only the user prepares for the knife and measuring tool, the operation can be started immediately. Perfect after-sales service (pre-sales, in-sales, after-sales, installation, debugging, training and maintenance etc.) in addition, one-year quality assurance service is granted. 12.Optional configuration: rolling working platform, Germany Mecano button station, heightening lathe and prolonging ram and square ram etc.

Main Features The production speed can be adjusted freely. Smoot hand flexible mechanical operation ,series control cutter to be heated without any heat conduction medium. The energy loss is greatly reduced, energy loss is greatly reduced, energy saving, with smooth cutting edge, no scorch mark. 1, The machine adopts our unique code way of innovation, can according to the product thickness, free to adjust code blade height, and about cutting tool installation can quickly adjust freely, make the knife model installation and debugging other brand slot machine more convenient than the market. 2, The machine fixture with material limit, can process according to the material shape size, material limit width adjustment, more convenient location. 3, This machine with function of eliminate waste, reduce artificial remove waste, steps, greatly improve the production efficiency. 4, Knife model temperature can be controlled, heating speed, few seconds can reach required temperature, to ensure the efficient production efficiency.

Main features The production speed can be adjusted freely. Smoot hand flexible mechanical operation , series control cutter to be heated without any heat conduction medium. The energy loss is greatly reduced, energy loss is greatly reduced, energy saving, with smooth cutting edge, no scorch mark. 1, the machine adopts our unique code way of innovation, can according to the product thickness, free to adjust code blade height, and about cutting tool installation can quickly adjust freely, make the knife model installation and debugging other brand slot machine more convenient than the market. 2, the machine fixture with material limit, can process according to the material shape size, material limit width adjustment, more convenient location. 3, this machine with function of eliminate waste, reduce artificial remove waste, steps, greatly improve the production efficiency. 4, knife model temperature can be controlled, heating speed, few seconds can reach required temperature, to ensure the efficient production efficiency.