SRT-01
Satellite Phone Indoor Amplifier Device (Inmarsat & Thuraya Suitable)
The Satellite Phone Indoor Amplifier Device is a device let your Inmarsat or Thuraya satellite phone can normally use in the room. (used in the boat, vehicle, building etc). Install this device with our special outdoor antenna and omni indoor antenna, making you keep in touch with others freely even in the room, you can call out and receive the incoming call even in the room, no need go out to search the satellite signal and wait for register, and at same time, the device can support up to 100 sets satellite phone communication at same time in the room which cover up to 120 square meters.
The basic principle of this device is that the outdoor antenna receives the downlink signal from the satellite (Inmarsat or Thuraya), through high selectivity band-pass filter to well isolate the passband signal, after amplifying by integrative power amplifier, then transferred by indoor antenna, meanwhile, on the way of uplink path, signal of satellite phone in the coverage area is transmitted to the satellite after disposing by uplink amplifying link path by same working mode.
For the Inmarsat and Thuraya satellite network system, downlink signal including: satellite and GPS L1 2 signal. The device has Automatic Level control ( ALC )System, automatic control the gain according to the circumstance.
Features:
-Keep your Satellite phone on communication status even in the room. Avoid miss coming call when you are in the room. And also you no need going outdoor for searching the satellite signal.
-The device can suitable for Inmarsat Isatphone Pro, Thuraya SO-2510, SG-2520, Thuraya XT etc models, and also GPS.
-Keep your satellite phone can move freely, unlike Fixed Satellite phone which canâ??t move, and also you can freely hand carry your satellite phone when need go out.
Application Range:
Boat driving room;
Emergency Vehicles;
Remote mine;
Earthquake or other emergency response administration;
Remote country where there dont have GSM mobile phone signal areas.
Marine Satellite TV Antenna
Model : EMA-V450/ V450L
General Description
The dependable EMA-V450/V450L auto tracking marine satellite TV systems
enable high quality satellite TV watching onboard in all conditions.
Features
Worldwide satellites database; quick lock signal with built-in GPS
Automatic identifier with a superior satellite tracking performance
High-performance antenna supported by a high precision gyro with 3-Axis movement.
Offsets shocks and waves at high speed traveling for any marine vessel
Easy installation and operation
Weather proofed
Application Supports
Dish Diameter :
45cm/17.7 inch
Dimension :
600mm(H) x 520mm(D)
Weight :
12kg/26lbs
Minimum EIRP:
48dBW
Reception frequency :
Ku-band(10.7~12.75GHz)
Local Frequency:
10750,11300,9750/10600MHz(Option)
Power Requirement :
AC 100V-240V/1.5A
Operating Voltage :
DC 24V
Environment Humidity
0~95%
Static Power Consumption:
12W
Elevation Range:
0°~90°
Temperature:
-30â??~70â??
Shipâ??s Motion:
Roll±25°,Pitch±15°,Yaw±8°@6 sec period
Azimuth Range :
0°~690°
Turning Rate :
More than 90°/sec
RF Output :
Dual/Quad
Water Ingress :
IP56
ACU Dimensions(WxDxH) :
179 x 140 x 54mm
Polarization :
Linear or Circular
Marine Satellite TV Antenna
Model : EMA-V450/ V450L
General Description
The dependable EMA-V450/V450L auto tracking marine satellite TV systems
enable high quality satellite TV watching onboard in all conditions.
Features
Worldwide satellites database; quick lock signal with built-in GPS
Automatic identifier with a superior satellite tracking performance
High-performance antenna supported by a high precision gyro with 3-Axis movement.
Offsets shocks and waves at high speed traveling for any marine vessel
Easy installation and operation
Weather proofed
Application Supports
Dish Diameter :
45cm/17.7 inch
Dimension :
600mm(H) x 520mm(D)
Weight :
12kg/26lbs
Minimum EIRP:
48dBW
Reception frequency :
Ku-band(10.7~12.75GHz)
Local Frequency:
10750,11300,9750/10600MHz(Option)
Power Requirement :
AC 100V-240V/1.5A
Operating Voltage :
DC 24V
Environment Humidity
0~95%
Static Power Consumption:
12W
Elevation Range:
0°~90°
Temperature:
-30~70
Ships Motion:
Roll±25°,Pitch±15°,Yaw±8°@6 sec period
Azimuth Range :
0°~690°
Turning Rate :
More than 90°/sec
RF Output :
Dual/Quad
Water Ingress :
IP56
ACU Dimensions(WxDxH) :
179 x 140 x 54mm
Polarization :
Linear or Circular
Model: fa-3-156a
Marine vhf antenna 156-163mhz , 1.12m, with 7m cable , and fix support for yacht
Frequency range- 156-163 mhz
Bandwidth- 5 mhz within 2.0:1 vswr
Impedance- 50 ohm
Vswr- nominally 1.5:1 at 159.5mhz
Gain 3db
Polarization- vertical
Maximum power input-watts 50w
Horizontal beam width- 360
Vertical beam width 58
Dc ground no dc ground
The antenna will read open on continuity test.
Height- 115010 mm
Radome material- fiberglass
Ferrule- pom
Coax supplied- rg-58u(white), 7m
Connector pl259, loosen
Weight- 420g
New model: hab-120
Marine fishing net ais tracking buoy/beacon
Feature:
1. Long time battery, more than 240 house each time
2. Smart gps antenna module allows an excellent gps signal receiving
3. Stable and reliable rf performance
4. High-level waterproofing protection up to ipx7
5. Self developed ais fishing net tracking buoy, allows you to get an accurate location at night, in rain, and fog.
Proved performance
Up to 12nm from a ship with ais a or b transponder
Application
Wanting for an accurate location of your fishing net? wanting to save your time and fuel to find your net?
Self developed ais fishing net tracking buoy, allows you to get an accurate location at night, in rain, and fog. Dont worry about losing your fishing net anymore!
Hab-80 ais fishing net tracking buoy unit uses advanced ais technology to transmit the combined data that include the unique id and the position of a net. And the data can be received effectively by the vessel equipped with ais device, then easily recognized and find back the nets with hab-80. Also it can avoid collision accidents by other boats.
Specification
Standards:
Ec62287-1: 2006-03
Iec60945: 2002
Itu-r m.1371-2
Position update: every 3 minutes
Working frequency: 161.975mhz / 162.025mhz
Output power: 34.8dbmâ±1.5dbm
Channel bandwidth: 25 khz
Modulation mode: gmsk
Bit rate: 9600b/sâ±50ppm(gmsk)
Dimension: 330 mm x 90mm
Weight: 0.5 kgs
Battery: 8.4v, 4000mah; rechargeable
Working time: more than 240 hours
Antenna: built-in vhf/gps antenna
Gps module: iec61108-1 standard
Working environment: -20c 55c
Waterproofing: ipx7
Equipment list:
Hab-120 tracking buoy unit
Battery recharger
New model: HAB-80
marine fishing net AIS tracking buoy/beacon
FEATURE:
1. Long time battery, more than 240 house each time
2. Smart GPS antenna module allows an excellent GPS signal receiving
3. Stable and reliable RF performance
4. High-level waterproofing protection up to IPX7
5. Self developed AIS Fishing Net Tracking Buoy, allows you to get an accurate location at night, in rain, and fog.
Proved Performance
Up to 12nm from a ship with AIS A or B transponder
Application
Wanting for an accurate location of your fishing net? Wanting to save your time and fuel to find your net?
Self developed AIS Fishing Net Tracking Buoy, allows you to get an accurate location at night, in rain, and fog. Dont worry about losing your fishing net anymore!
HAB-80 AIS Fishing Net Tracking Buoy unit uses advanced AIS technology to transmit the combined data that include the unique ID and the position of a net. And the data can be received effectively by the vessel equipped with AIS device, then easily recognized and find back the nets with HAB-80. Also it can avoid collision accidents by other boats.
Specification
Standards:
EC62287-1: 2006-03
IEC60945: 2002
ITU-R M.1371-2
Position update: every 3 minutes
Working frequency: 161.975MHz / 162.025MHz
Output power: 34.8dBm±1.5dBm
Channel bandwidth: 25 KHz
Modulation mode: GMSK
Bit Rate: 9600b/s±50ppm(GMSK)
Dimension: 330 mm x 90mm
Weight: 0.5 KGS
Battery: 8.4V, 4000mAh; rechargeable
Working time: More than 240 hours
Antenna: Built-in VHF/GPS antenna
GPS Module: IEC61108-1 standard
Working Environment: -20C 55C
Waterproofing: IPX7
Equipment List:
HAB-80 Tracking Buoy unit
Battery recharger
Matsutec
MODEL: KP-628F KP-828F KP-1228F
COLOR LCD GPS Plotter combo with Fish finder
FEATURE:
1 High Resolution
1) KP-628F: 5.6 inches Color TFT Display, 640*640 pixels
2) KP-828F: 8 inches Color TFT Display, 800*600 pixels
3) KP-1228F: 12 inches Color TFT Display, 800*600 pixels
2. 8 Color or 8 Level Amber Presentation
3. 50/200 KHz Transceivers, Output Power:
1) KP-628F 300 Watt
2) KP-828F 600 Watt
3) KP-1228F 600 Watt
4. Blue, Light Blue, or Black Background Color
5. 8 Range Scales, from 0-15 to 0-1000 Feet
6. Range Offset to 0-100 meters
7. Automatic Range and Grain Selection Mode
8. A-Scope Display for Rapid Fish ID and Detection
9. Multiple Display Modes:
10. Digital Display of Speed, Depth, Water Temp and Position
11. Adjustable Bottom or Fish Alarm
12. Calibration in Feet, Fathoms or Meter
13. Built-in Picture Simulator
14. SD-cards slot for C-Map and user data
15. C-Map MAX and K-Chart Selectable
16. Tide table and Celestial
17. Versatile Display Mode Include
18. GOTO track navigation
19. MAP orientation select
20. Proximity waypoints alarms
21. Perspective View
22. MAP Palette
SPECIFICATION
PLOTTER CHARACTERISTICS
1. Waypoints/Icons: 14,000 waypoints with name, symbol, 10 proximity waypoint.
2. Route Memory: waypoint up to 169 points each, plus MOB and Track Navigator or Goto Track modes
3. Tracks: 21,000 points automatic track log; 15 saved track (up to 2100 track points each) Let you retrace your path in both directions
4. Alarm: XTE, Anchor Drag, Arrival, Speed, Voltage, Proximity, Waypoint and Time, AIS alarm.
5. Palette
6. Tides: Tide Data
7. Projection: Mercator projection
8. Position format: Lat/Lon
9. Base Map: Built-in ONWA K-Chart
10. External Map: SD cards slot for user settings
11. User data storage: Internal backup of user settings, or external SD-card
12. Plot Interval: 1s to 99h or 0.01nm to 9.99nm
13. Polotting scales: 0.01nm to 1,000nm
14. Nav Data Input/Output:
ECHO SOUNDER
Echo Color
8 colors (including background color) according to echo intensity. Monochrome display is also available. The background color is selectable from blue, light blue, white and black.
Basic Range
Meters: 10/20/40/80/150/200/300/500/1000
(for HP-628F, up to 600m)
Feet: 30/60/120/200/400/600/1000/1600/3000
( for HP-628F, up to 1500ft)
AIS interface
Data input: NMEA0183, RS232
Baud rate: 38,400
Power Supply:
1) KP-628F: 10.5 to 35VDC, current drain 1.0A at 12V
2) KP-828F/1228F: 10.5 to 35VDC, current drain 2.5A at 12V
Matsutec
8" Color LCD Marine AIS class B transponder / GPS chartplotterlotter
Model: HP-828A
FEATURE:
1. High resolution TFT day-view LCD display
2. SD-cards slot for C-map Max and user data
3. C-map Max and K-chart Selectable
4. Tide table
5. Versatile display modes including:
- Plotter Screen
- Nav Data
- Satellite Information
- AIS Display
- Compass Screen
6. GOTO Track Navigation
7. Map Orientation Select
8. Proximity waypoint alarms
9. Perspective View
10. Palette
- Normal
- Daylight - Exposed to Sunlight
- Night - In Dark Environment
- NOAA - Paper Chart Colors
- Celestial
SPECIFICATIONS
Plotter Characteristics
1. Waypoints/Icons: 14,000 waypoints with name, symbol, 10 proximity waypoint.
2. Route Memory: waypoint up to 169 points each, plus MOB and Track Navigator or Goto track modes
3. Tracks: 21,000 point automatic track log; 10 saved track (up to 2100 track points each) let you retrace your path in both derections
4. Alarm: XTE, Anchor Drag, Arrival, Speed, Voltage, Proximity, Waypoint and Time, AIS alarm.
5. PALLETE
- Normal
- Daylight: Exposed to sunlight
- Night: In dark environment
- NOAA: Paper chart color
6. Tides: Tide Data
7. Projection: Mercator projection
8. Position format: Lat/Lon
9. Base Map: Built-in ONWA K-Chart
10. External Map: SD cards slot for user settings
11. User data storage: Internal backup of user settings, or external SD-card
12. Plot Interval: 1s to 99h or 0.01nm to 9.99nm
13. 0.01nm to 1,000nm
14. Nav Data Input/Output:
- Input:
$--DBT, $--DPT, $--GGA, $--GLL, $--MTW, $--RMA, $--RMB, $--RMC, $--VHW, $--VTG, $--ZDA
- Output:
$--AAM, $--APB, $--BOD, $--BWC, $--GGA, $--GLL, $--RMB, $--RMC, $--VTG, $--XTE, $--ZDA, $--WPL, $--HDG
- Output for autopilot:
$--AAM, $--APB, $--BOD, $--VTG
15. PERSPECTIVE VIEW: On/off
GPS Receiver Characteristics
1. Receiver: 50 parallel channel GPS receiver continuously Tracks and uses up to 50 satellites to compute and update your position
2. Acquisition: Cold start: 27 seconds average
Warm start: 27 seconds average
Hot start: 1 seconds average
3. Update rate: 1/second, continuous
4. Accuracy: Position:
Matsutec
12" Color LCD Marine GPS chart plotter
Model: HP-1228
FEATURE:
1. High resolution TFT day-view LCD display
2. SD-cards slot for C-map Max and user data
3. C-map Max and K-chart Selectable
4. Tide table
5. Versatile display modes including:
- Plotter Screen
- Nav Data
- Satellite Information
- AIS Display
- Compass Screen
6. GOTO Track Navigation
7. Map Orientation Select
8. Proximity waypoint alarms
9. Perspective View
10. Palette
- Normal
- Daylight - Exposed to Sunlight
- Night - In Dark Environment
- NOAA - Paper Chart Colors
- Celestial
SPECIFICATIONS
Plotter Characteristics
1. Waypoints/Icons: 14,000 waypoints with name, symbol, 10 proximity waypoint.
2. Route Memory: waypoint up to 169 points each, plus MOB and Track Navigator or Goto track modes
3. Tracks: 21,000 point automatic track log; 10 saved track (up to 2100 track points each) let you retrace your path in both derections
4. Alarm: XTE, Anchor Drag, Arrival, Speed, Voltage, Proximity, Waypoint and Time, AIS alarm.
5. PALLETE
- Normal
- Daylight: Exposed to sunlight
- Night: In dark environment
- NOAA: Paper chart color
6. Tides: Tide Data
7. Projection: Mercator projection
8. Position format: Lat/Lon
9. Base Map: Built-in ONWA K-Chart
10. External Map: SD cards slot for user settings
11. User data storage: Internal backup of user settings, or external SD-card
12. Plot Interval: 1s to 99h or 0.01nm to 9.99nm
13. 0.01nm to 1,000nm
14. Nav Data Input/Output:
- Input:
$--DBT, $--DPT, $--GGA, $--GLL, $--MTW, $--RMA, $--RMB, $--RMC, $--VHW, $--VTG, $--ZDA
- Output:
$--AAM, $--APB, $--BOD, $--BWC, $--GGA, $--GLL, $--RMB, $--RMC, $--VTG, $--XTE, $--ZDA, $--WPL, $--HDG
- Output for autopilot:
$--AAM, $--APB, $--BOD, $--VTG
15. PERSPECTIVE VIEW: On/off
GPS Receiver Characteristics
1. Receiver: 50 parallel channel GPS receiver continuously Tracks and uses up to 50 satellites to compute and update your position
2. Acquisition: Cold start: 27 seconds average
Warm start: 27 seconds average
Hot start: 1 seconds average
3. Update rate: 1/second, continuous
4. Accuracy: Position:
GPS Antenna with Heading Signal output NMEA0183
KA-GC01
KA-GC05
KA-GC10
Features
NMEA0183 Output (RS232), baud rate: 4800
-KA-GC01
GGS, GLL, GAV, RMC, VTG, GMS, HDT: 1HZ
-KA-GC05
GGA, RMC, VTG, GMS: 1HZ, HDT: 5HZ
-KA-GC10
HDT(10HZ)
KA-GC01 suitable to use with GPS Plotter, ECDIS
KA-GC05 is suitable to use with Marine Radar, Autopilot
Can work independently with other navigation equipment
Working voltage: 5~18 VDC
True heading with magnetic variation
Provide high accuracy heading and position data
Economic solution of heading and position information
Built-in 3D digital magnetic sensor and 3D linear acceleration sensor
±1.3 to 8.1 gauss magnetic field
Technical Specifications:
Antenna Types: Outdoor installation
Center Frequency: 1575.42MHZ ±5MHZ
Power supply: DC 6V 13.5V
Current: 30MA
Impedance: 50
Gain: 30DB ±1DB
VSWR: 1: 1.5
Noise figure: 1.5
Temperature: -40+85
Axial ration: 4DB
Electronics compass:
Precision:
±3°degrees with proper calibration without nearby magnetic disturbace(typical):
±5°degrees with extreme northern and southern latitudes
Resolution: 1°
Antenna Cables: 10M
The antenna has a strong anti-jamming performance, short positioning time, high Accuracy and good waterproof performance
Model: KP -708
7-inch LCD GPS Chart Plotter with Internal GPS Antenna
Features:
Easy to Operate
7-inch high resolution (800x600 pixels ) LCD
Built -in GPS Antenna , External Antenna can be used as an option
Supports Dual Mapping System : K-Chart and C-Map
Plotter characteristic
Waypoint/icons: 12000 user waypoints with name, symbol
3 system waypoints: MOB, Start, Cursor
10 proximity waypoints
Routes: Max 30 routes. And up to 170 points for each one
Tracks: 8000 points automatic track log:
10 saved tracks (up to 8000 track points each)
Let you retrace your path in both directions
Alarms: XTE, Anchor drag, arrival speed, voltage, proximity waypoint and time, AIS
Tides: Tide data
Projection: Mercator projection
Position format: Degree of minutes and UTM
Base map: Built -in ONWA K -Chart
External Map: SD Cards slot for C -Map MAX and ONWA K -Chart
User data storage: Internal backup of user settings or external SD -card
Plot interval: 5s to 60min 0.01nm to 10nm Automatic way
Plotting scales: 0.001nm to 1000nm
Perspective View: Onto/Off
Celestial: Sunrise/Sunset Moonrise/Moonset
Power supply : 10.5 to 35V DC, current drain
CPT-190 Table Model Magnetic Compass
CPT-190 Magnetic Compass is a sort of table model liquid magnetic compass . It is used for the middle and small vessels acting as steering compass . The compass is a magnetic compass class A and it is designed and manufactured on the basis of the national standard GB/T 14108-93 ( General Technical Terms of Marine Magnetic Compass Class A ),its technical performance index are completely in accordance with the national standard. The product has the advantages of beautiful outline,high precision,convenient correcting difference,steady performance and legible lighting etc. It is the essential navigation instrument for the middle and small vessels.
7-INCH COLOR DISPLAY FISH FINDER
MODEL: Kfish-7
FEATURE:
1) Dual-frequency: 50 and 200 KHz
2) 7-inch TFT LCD display with 8-color or multi-level amber presentation
3) Auto Mode for hands-off operation
4) Variety of display modes: A-scope, bottom-lock expansion, marker zoom and unique bottom zoom displays
5) Compound Temperature sensor option
SPECIFICATIONS
1.General
(1) Display
7?�inch TFT LCD
(2) Echo Color
8 colors (including background color) according to echo intensity. Monochrome display is also available. The background color is selectable from blue, light blue, white and black.
(3) Basic Range
Meters: 5/10/20/40/80/150/200/300
Feet: 15/30/60/120/200/400/600/1000
Fathoms: 3/5/10/20/40/80/100/150
Passi/Braza: 3/5/10/30/50/100/150/200
The basic ranges can be changed on the system menu.
(4) Range Shift
Up to 300 meters (1000 feet, 150fathoms, 200 passi/braza)
(5) Zoom Range
Times 2, 3, 4 and 5 ranges
(6) Bottom Lock Expansion Range
5/10meters, 10/20feet, 2/5fathoms, 2/5passi/braza
(7) Auto Mode
Automatic adjustment of range and gain
(8) Display Mode
High Frequency (200K),Low Frequency (50K), Dual (200K and 50K 1/2display on each), Zoom (200K and 50K zoom) and A-scope Display
(9) Zoom Display
Marker Zoom, Bottom Zoom and Bottom-lock Expansion
(10) Display Advance Speed
Lines/TX: Freeze, 1/8, 1/4, 1/2, 1/1, 2/1
(11) TX Frequency Output power
50 and 200kHz (alternately transmitted), 300W
(12) Pulse-length/TX rate
Display End Depth(m) 5, 10, 20, 40, 80, 150, 300
Pulse-Length(ms) 0.2, 0.2, 0.2, 0.4, 0.8, 1.5, 3.0
TX Rate(pulse/min) 600, 600, 600, 375, 187, 100, 50
(13) Interference Rejecter
Rejects unwanted signals by comparing last and present echoes in strength.
(14) Alarm
Fish and Bottom alarms, Temperature alarm (sensor required)
(15) Input/output data
Input
Output
NMEA0183
RMC, VTG
SDDBT, SDDPT
2. Power Supply
(1) Display Unit
12-24 VDC -10%, +30%: 1.0 - 0.6 A
3. Environmental Condition
(1) Ambient Temperature
0to + 50
(2) Relative Humidity
85% at 40
(3) Water proofing
Display Unit: IPX4
(4) Vibration
±1mm ±10%, 2(5) to 13.2Hz, Maximum acceleration 7 m/s, 13.2 to 100Hz
4. Coating Color
(1) Display Unit
Chassis: 2.5GY5/1.5
Panel: N3.0 New tone No.5
Matsutec Class B AIS Transponder
Model: HA-102
FEATURES
Electrical function is accordance with IEC 62297-1
Dual Channel function: Two TDMA receivers ar receiving datum in two independent channels at the same time, and one TDMA transmitter is transmitting in two independent channels alternately.
CSTDMA function can avoid and solve communication conflict.
Transponder has external serial data interface(RS-422, RS-232).
Transmit and reciever safety message, and equipped with "SOS" safety button.
Support three operation mode: Carrier-sense mode, assigned mode and polled mode.
Internal GPS reciever, as data source for position, COG and SOG can be connected to all devices compatible to GPS and PC, PDA, ECDIS, RADAR, etc.
Alarm and indication (via LED) for power , error, time-out, status.
Specifications
STANDARDS
IEC 62297-1
IEC 61162-1
IEC 60945-2002
VHF RECEIVER
Frequency Range
156.025MHZ ~ 162.025 MHZ
Channel Bandwidth
25 KHZ
Number of AIS Receivers
2 Receiver ( one time shared between
AIS/DSC ) / 1 Transmitter
CH-1
Default CH 87B ( 161.975 MHZ )
CH-2
Default CH 88B ( 162.025 MHZ )
Number of DSC Receiver
1 ( CH 70)
RX DSC
156.525 MHZ
Max. Usable Sensitivity
PER less 20% at -107dBm
VHF TRANSMITTER
Power Output
2 Watt ( 33 dBm ±1.5dB )
Modulation
GMSK / FM
Data Rate
9.6K dps / per channel
Modulation Spectrum
IEC 62287
DSC RECEIVER
Modulation
1300 HZ / 2100 Hz FSK
Data Rate
1200 bps ± 30 ppm
Spurious Response Rejection
Over 70dB for Signal @ -104dBm; BER less 1%
Blocking
More 84dB for Signal @ -104dBm; BER less 1%
GPS RECEIVER
Receiving Channels
12 Channels
Acquisition Sensitivity
-140dBm
Tracking Sensitivity
-150 dBm
Position Accuracy
< 2.5m CEP ( GPS ) without SA
Output Rate
1 Hz
POWER SUPPLY
Supply Voltage
12V DC ( 10V ~ 20V )
Power Consumption
Less than 10W
MAIN UNIT
4 LED Indicator Working Status
1 ON/OFF Switcher
INTERFACE
Ports
NMEA 0183 / RS-422 / RS-232
GPS Antenna ( Optional )
Female TNC Connector
VHF Antenna ( Optional )
Female Type M Connector
( Type N Connector optional )
ENVIROMENT
Operating Temperature
Antenna : -25 ~ 70 C Celcius
Others : -15 ~ 55 C Celcius
Storage Temperature
-25 ~ 70 C Celcius
Humidity
Operating: 0 ~ 95 RH at 40 C Celcius
GPS Antenna operating : 100% Hermetically sealed
VHF Antenna operating : 100% Hermetically sealed
Vibration
IEC 60945
Waterproof
IPX5
PHYSICAL
Size in mm ( W )
234mm
Size in mm ( H )
40mm
Size in mm ( D )
167mm
Weight
BRIEF The ISATDOCK2 enables the Isatphone 2 to be always on and ready for service (Call and Receiver). The Isatphone 2 handset features include phone charging management, USB data port, inbuilt ringer and allows antenna and power to be permanently connected to the dock ready for use.
APPLICATION Keep satellite signal on status whenever and wherever on the global . Avoid miss incoming call, and call out satellite phone in your drive room or office. In remote areas also let Isatphone 2 have good receiving ability. FEATURES Quickly searching satellite and GPS Position Charging control switch and LED indicator for battery charging status
High signal receive ability by marine active antenna Inbuilt Hands-free speaker phone USB Data access High quality ABS plastic Wall or desk mounting options Integrated Antenna design
SPECIFICATION:
POWER 9~36V DC input lead AC/DC adaptor (Optional) ANTENNA WORK FREQUENCY Inmarsat Receiver: 1525.0 to 1559.0 MHZ, 1575.42+/- 10.25MHZ (GPS L1 ) Inmarsat Transmit: 1626.5 to 1660.5 MHZ Antenna Description: Type marinetime POWER CONSUMPTION Charging: 500mA, 6W Sleep mode: 5mA, 60mW PHYSICAL Dimensions: 219 x 166 x 85 mm Weight â?? dock: 0.687g ENVIRONMENT Operating Range: -30 C to +80 C Storage: -35 C to +85 C Battery Charging Temp.: 0 C to +45 C Operating Humidity Range: 95% at 40 C Storage Humidity Range: 95% at 45 C IN THE BOX 1. ISATDOCK2 main unit x 1 2. Privacy handset x 1 3. DC Power Cable / Lead x 1 4. Active Satellite Antenna x 1 5. Satellite Antenna Mounting bracket x 2 6. 5M/10M Antenna Cable x 1 7. User manual x 1
Matsutec
HP-33A
4.3" color LCD diaply AIS transponder combo with GPS navigator
The HP-33A is a class B AIS transponder for Non-SOLAS vessels such as pleasurecraft, work-boat, fishing boat etc small boat.
Special design Watching dispaly to monitor Fishing net buoy, friendly ships etc. External Alarm for MOB and Collision-Risk management.
Feature
To AIS
1. Detail Target list and Radar overview
2. Watching disaply to monitor important subject, example: Fihsing net buoy, Friend ship etc
3. External Alarm (Buzzer)
4. Low cost, reduced size and easy installation make the HP-33A ideal to meet your budgets and demands of owners and vessel operators
To GPS
1. 4.3" Sunlight Viewvable color LCD (Brightness: 500 cd)
2. GOTO track navigation
3. Stores up to 10,000 marks/ waypoints, 100 routes and 3,000 track points
4. Delicated Man Over Board Button (MOB)
5. Support NMEA 0183 ver 2.0
6. 7 display modes available, including 2 user-customized modes
7. SBAS capable for better measurement
Equipment list ( standard):
1. Dispaly unit HP-33
2. Antenna unit HA-017 with cable 10m
3. Power canle, 2m
4. Standard spare parts and installation material
5. Operator manual
Satellite Emergency Position-indicating Radio Beacon
406MHz EPIRB VEP-8
Summary
When the vessel is in distress, VEP8 shows bit standard will be automatically ejected from the release device, transmitter 406MHz emergency signal, Cospas / Sarsat system satellite signal is received, will be communicated to the shore-based terminal. LUT (Local User Terminal) decoding analysis to produce bit, position, and to convey the RCC (rescue center), in order to implement the emergency.
VEP8 satellite emergency position indicating radio beacon designed according to the latest national and international standards for domestic and international various vessels. Additional 121.5MHz locator transmitters to facilitate maritime search and rescue teams quickly locate the location of the incident, significantly shortening the rescue time.
Product Features:
Automatic and manual start; contain the 121.5MHz auxiliary locator transmitter to facilitate wireless relocation; automatically release the device with a hydrostatic release unit; automatically turn on at night, high-brightness flash; GPS global positioning system.
The VEP8 is available as float-free deckmounted device using HydrostaticRelease Mechanism to be activated automatically on 4m depth.
Three LEDs provide indication of 406 ( COSPAS-SARSAT) and 121.5MHz ( SARhoming Frequency ) transmitters and battery status .
Easy Changeable 2-cell Lithium battery with 5 years life . Small size and weight make PRO-5 anideal solution for pleasure boats and yachts .
High Stability in upright position on wavy surface
Ultra high performance solid state strobe .
Easy Test facilities with Visual indication.
Proper operation on sea surface , wooden deck or held in hand .
Product Specification:
1)406 MHz satellite transmitters
Output frequency: 406.028MHz ± 1kHz
Output Power: 5W (37dBm) ± 2dB
Phase modulation: peak 1.1rad ± 0.1rad
Encoding: biphasic L coding
2) 121.5 MHz find bits transmitter
Output frequency: 121.5MHz ± 3kHz
Output power:> 50mW (+17 dBm)
Phase manner: A3X
Transmit duty cycle: 100% (continuous emission)
3) GPS satellite positioning system
Receive Channel: 50
Sensitivity:-160dBm
Positioning accuracy: 2.5m
Hot start:
Search and Rescue Radar Transponder SART
Model: TBR-600C
Product Overview: Search and rescue radar transponder (SART) is the positioner of global maritime distress and safety system (GMDSS). Performance indicators of the product meet relevant international standards. It possesses independent intellectual property right and has obtained the model approval from China Classification Society (CCS) (certificate number: CQ08T00015).
Function and Purpose:
It is capable of detecting the pulse action through the navigation radar installed on a search and rescue vessel or a helicopter. The signal from SART can indicate exact position of the SART on the fluorescent screen of navigation radar of the search and rescue vessel of the helicopter.
The survivor who holds a SART or a ship or boat in distress where a SART is equipped can discover the search and rescue vessel or helicopter that is approaching them.
Technical Indicators:
Signal:
Frequency range: 9,200MHz -9,500MHz.
Polarization: horizontal polarization.
Antenna:
horizontal beam (omnidirectional)
Marine 4.5� color LCD marine Autopilot for boat
Model: KAP-866
Feature:
1) Fluxgate heading sensor with high accuracy and stability
2) Automatic correction for local magnetic variation
3) 4.5 silver bright LCD display
4) Off course alarm warns when vessel is not responding to autopilot control
5) Navigate with designed route of GPS Navigator
6) Timer can be used as an adjustable watch alarm
7) Gyro compass input with Gyro converter unit
Specification of KAP-866
Function
1) Auto mode:
- Change course by panel dial knob
- Change course by fix or handheld
Remote (optional)
2) Standby mode
3) GPS Navigation mode
4) Follow UP mode
Steering system
Hydraulic or Electro-mechanical
Heading sensor
1) Fluxgate heading sensor (standard)
2) Gyro compass thru Gyro converter (optional)
Nav sensor
GPS Navigator: NMEA0183, APA, APB (baud rate: 4800)
Heading input: NMEA0183, HDT, HDG or HDM (baud rate: 4800)
Adjustment of parameters
Weather, Rudder and Counter Rudder from Control menu
Trim, Rudder Ratio and Rudder Limit from Function menu
Alarm
1) Off course alarm: 0~180 degree adjustable
2) Watch alarm: 1~60 adjustable watch alarm.
Will trigger external alarm if not reset within 60 sec.
3) NMEA data alarm: Trigger when lost of NMEA data from GPS Navigator in GPS
Power Supply
12V or 24VDC, Standby 0.4A, Auto mode 1.0A for control unit only
Equipment List
- KAP-866 control unit
- Rudder Feedback unit KRF-36
- Fluxgate heading sensor KFG-25
- Standard accessories
- Standard installation kit
- Operator manual
Long Range Acoustic Device - QS II
Long Range Acoustic Device (LRAD) QS II is a breakthrough hailing andwarning, directed acoustic device designed to communicate with authorityand exceptionally high intelligibility.
What makes the LRAD product unique is its ability to transmit your messagewith exceptional voice intelligibility and tonal clarity in a highlydirectional beam, even with significant ambient noise. The directionalityof the LRAD device reduces the risk of exposing nearby personnel orperipheral bystanders to harmful audio levels.
Applications:
*Bird control for airports, airfields, landfills, mines & wind farms.
*Waterside force protection
*Crowd & Riot control
*Building clearing operations
*Psychological operations
*Visit board search & Seizure
*Remote-operation infrastructure force protection
*Ground/mechanized offense/defense operations.
New model: HAB-120S
marine fishing net AIS tracking buoy/beacon with SOS safety button
FEATURE:
1. Long time battery, more than 240 house each time
2. Smart GPS antenna module allows an excellent GPS signal receiving
3. Stable and reliable RF performance
4. High-level waterproofing protection up to IPX7
5. Self developed AIS Fishing Net Tracking Buoy, allows you to get an accurate location at night, in rain, and fog.
Proved Performance
Up to 12nm from a ship with AIS A or B transponder
Application
Wanting for an accurate location of your fishing net? Wanting to save your time and fuel to find your net?
Self developed AIS Fishing Net Tracking Buoy, allows you to get an accurate location at night, in rain, and fog. Donâ??t worry about losing your fishing net anymore!
HAB-80 AIS Fishing Net Tracking Buoy unit uses advanced AIS technology to transmit the combined data that include the unique ID and the position of a net. And the data can be received effectively by the vessel equipped with AIS device, then easily recognized and find back the nets with HAB-80. Also it can avoid collision accidents by other boats.
Specification
Standards:
EC62287-1: 2006-03
IEC60945: 2002
ITU-R M.1371-2
Position update: every 3 minutes
Working frequency: 161.975MHz / 162.025MHz
Output power: 34.8dBm±1.5dBm
Channel bandwidth: 25 KHz
Modulation mode: GMSK
Bit Rate: 9600b/s±50ppm(GMSK)
Dimension: 330 mm x 90mm
Weight: 0.5 KGS
Battery: 8.4V, 4000mAh; rechargeable
Working time: More than 240 hours
Antenna: Built-in VHF/GPS antenna
GPS Module: IEC61108-1 standard
Working Environment: -20C â?? 55C
Waterproofing: IPX7
Equipment List:
HAB-120s Tracking Buoy unit
Battery recharger
KS-33R Matsutec AIS MOB personal locator beacon
Features:
Transmits GPS target tracking information over AIS
Compatible with plotters and onboard navigation systems to assist fast location and retrieval
Small and lightweight for mounting on life jacket
Unique serialized ID
LED flashing indicator
Buzzer
Minimum 24hour continuous operation
7 year battery life
Specifications
Standards: EC 61097 -14, 60945 (environmental /EMC),
61108 part 1, ITU RM, 1371
Sealing depth: Immersion to 5m (16.4ft)
Operating temperature: -20 to +55oC (-4 to +131oF)
Storage temperature: -30 to +70oC (-22 to +158oF)
Battery type: Lithium Manganese
Transmit duration: 24 hours
Battery life (storage): 7 years
Frequency: 161.975 &162.025MHz
Power: 2W nominal
AlS Messages transmitted: Message 1 (UID, GPS position, SOG ,COG ,UTC )
Message 14 (MOB ACTIVE or MOB TEST)
First Transmission: After 15 seconds (No GPS)
Range: 4nm typical, with AIS receiver antenna >5m above sea level
Unique ID Number: Factory Programmed
GPS Type: 50 channel, ceramic patch antenna
GPS Position Update; Every minute
Size (D x W x L): 24 x 50 x 130mm (0.93 x 1.96 x 5.08in)
Weight: 120g (4.23oz)
Standard Compass Safe Distance: 0.1-10 at 30cm (1ft)
GMDSS NAVEX RECEIVER HX2600
H-Field ANT
518KHz , 490KHz , 4209.5KHZ, 486KHz , 4 Chanels
CCS Certificater .
IEC-61097-6
IEC-60945 (2002)
Specification:
1. Receive Frequency: 518KHz, 490KHz, 486KHz and 4209.5KHz.
2. Can receive channels:
Dual-channel (ie, a receiver operating in 518KHz channel, and the other receivers in the 490KHz / 486KHz/4209.5KHz switch between)
3. Sensitivity:
Useful at-107dBm signal level, the bit error rate of less than 1% of Chinese and English error rate of less than 4%.
4. Selective anti-jamming performance:
Blocking rejection ratio: In accordance with IEC61097-6 standards for frequency of strong signal interference, receive helpful information No less than 1% error rate in Chinese and English error rate of less than 4%.
5. Antenna Protection:
In the antenna signal with no modulation amplitude emf30V Frequency range of 100KHz ~ 28MHz, 15 minutes after the device is still working properly.
6. Monitor specifications: 7-inch color screen display
7. Information storage function:
Can store 200 messages, with an average of 500 characters each message, the storage time of 60 - 72 hours. Tag information can be stored permanently and you can not manually delete the.
8. External interface: an INS interface, a print output interface, USB interface.
9. Can be configured SII-DPU-414 type of thermal printing, the output format RS-232electrical interfaces
10. Sound the alarm: the volume of not less than 75dBA ~ 85dBA.
11. Power supply: 12VDC ~ 36VDC
12. Weight: 1135 g
13. The technical conditions of the legal basis: IMO ResolutionMSC148 (77), IEC 61097-6, IEC 60945 (2002).
Matsutec
HF-620 Echo Sounder
Newly Employed Digital Filter Technology presents high definition echo presentation of fish targets!
Description
The MATSUTEC HF-620 is a high performance, dual-frequency color digital echo sounder (50 and 200 kHz) with high transmission output power of 300 Watts. It has been designed specifically with small fishing and recreational boats in mind
The HF-620 employs a 5.6 sunlight viewable bright 256 color LCD (TFT) screen for vivid display and wide viewing angle. High resolution can reach to 480 x 640 pixels.
Features
1.Enhanced digital filter delivers comprehensive detection in both shallow and deep water
2.The mainly bang (echo just below the transducer) is suppressed to less than 40 cm so that the fish echoes below the transducer can easily be observed
3.Two types of Auto Modes available: Auto Gain and Auto Range
4.Fast pulse transmission rate to achieve outstanding shallow water echo presentation
5.Dual frequency 50/200 kHz
6.5.6 sunlight viewable bright 256 color LCD with a wide viewing angle
7.8 different colors of Background selectable
8.Easy to table-top mounted and flush mount
9.Audio-visual alarms for water depth, fish echoes.
Digital Filter Technology
The HF-620 features a digital filter, which delivers automatic gain control to present precise and crystal clear echo images.
However, even the best digital filter wont help unless you start with a solid base, such as MATSUTECs remarkable fish finder technology.
Specification of HF-620
GENERAL
Frequency: 50 and 200 kHz
Output Power: 300W
DISPLAY
Display Type: 5.6 Color LCD
Effective Display Area: 84.7 (W) x 113.3 (H) mm
Pixel Number: 480 x 640 pixels
Display Mode: Single frequency (high/low freq.), Dual-frequency, Wave Zoom, A-Scope
Basic Range: 1-1000 m (m, ft is selectable in the menu)
Range Phasing: up to 1000 m
Wave Zoom: 2X, 4X, 8X, XR
Picture Advance Speed: 5 steps is selectable
Pulselength & PRR: 0.1-3 ms, Max 3,000 pulse/min
Data Record: 1s, 15s, 30s, 1min
Data Interface: NMEA0183
POWER SUPPY: 11-35 VDC: 0.8-0.4 A
EQUIPMENT LIST:
1.Display Unit HF-620
2.Transducer w/ 10M cable
3.Installation Materials and Standard Spare Parts
4.Operating Manual
