Brief introduction:
Lt-01 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-01 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-01 leakage tester complies with astm d3078 and gb/t 15171 standards.
The leak detection system is composed of the mainframe and the vacuum chamber. A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated.
Features
Lt-01 leak tester uses vacuum ejector to generate stable vacuum environment. .
The leak detection requires no electricity
High leakage test efficiency
Extra-thick perspex
Different chamber sizes available
No calibration needed
No vacuum pump required
Easy installation, start-up and operation
Low maintenance
Astm d3078 , gb/t 15171
Brief introduction:
Lt-02 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-02 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-03 leakage tester complies with astm d3078 and gb/t 15171 standards.
The leak detection system is composed of the mainframe and the vacuum chamber.
A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated.
Features
Astm d3078 gb/t 15171
Brief introduction:
Lt-03 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-03 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-03 leakage tester complies with astm d3078 and gb/t 15171 standards.
The leak detection system is composed of the mainframe and the vacuum chamber. A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated.
Features
Lt-03 leak tester uses vacuum ejector to generate stable vacuum environment. The state-of-the-art human-computer interface and plc control unit on the leakage detection system make the parameter setting and test operation direct and easy. By saving different groups of parameters, users are free from the troubles of setting parameters each time before use. At the same time, different testing results and total test numbers can be saved to avoid any human errors.
1. Leak test process all automatic
2. Touching screen operation
3. Digital vacuum degree and test time input
4. Parameters and test data automatic saving
5. Automatic vacuum maintenance and air back-flushing
6. Extra-thick perspex
7. Different chamber sizes available
8. No vacuum pump required
9. Easy operation and maintenance
Astm d3078 , gb/t 15171
Application and Brief Intro
LSST-01 Leak and Seal Strength Tester is suitable for the quantitative determination of sealing strength, heating sealing quality, burst pressure and leakage of flexible and aseptic packages. The Leak and Seal Strength Detector can also be used to determine the sealing performance of pilfer-free bottle caps and soft tubes. The compression strength, connection strength of cap and body, cap losing strength, seal strength and butting strength of tubes are the applications of LSST-01 Seal Strength Testing System.
This Seal Strength Testing System conforms to standards of ISO 11607-1, ISO 11607-2, ASTM F1140, ASTM F2054, GB/T 10440, GB 18454, GB 19741, GB 17447, GB/T 17876, GB/T 10004, BB/T 0025, QB/T 1871, YBB 00252005, YBB 00162002 .
Principle
The three test modes of the positive pressure method, which LSST-01 Leak and Seal Strength Tester satisfies are as follows:
A. Burst Test: LSST-01 Leak and Seal Strength Tester internally pressurizes the packages until the package fails. The test pressure is the maximum pressure detected before the package fails.
B. Creep Test: Pressurize the package internally to a specific pressure and maintains this pressure for a specific time. The test measure is pass/fail.
C. Creep to Failure: The package is creep-tested and held until the package fails. The pressure setting is higher than that of the creep test to ensure the package fails in some time. The measure is the time until failure.
Application and Brief Intro
HST-01 Heat Seal Tester is for the determination of the heatsealability of a surface, or sealant layer of films, laminates, composites and polymers etc. How well the material heatseals is expressed quantitatively as seal strength as a function of the sealing conditions of temperature, time and pressure. HST-01 Heat Seal Tester is professionally designed for the precise measurement of the three parameters of temperature, time and pressure in the heat seal process. HST-01 Heatsealability Tester conforms to standards of ASTM F2029, QB/T 2358 and YBB 00122003.
Principle
Place a sample between two-heated sealing jaws of HST-01 Heat Seal Tester with flat surfaces when the required temperature reaches equilibrium. The upper seal jaw, driven by a gas cylinder, is pushed down, to exert a certain pressure on the sample and remain for some time. When the preset sealing time ends, the upper sealing jaw returns to its original position and the whole heatsealability testing process finishes.
ASTM F2029, QB/T 2358, YBB 00122003
FST-01 Film Free Shrink Tester
Introduction:
In the realm of plastic manufacturing, ensuring quality and process efficiency is paramount. Plastic films and sheets undergo intricate processes, leaving behind internal stresses that can lead to dimensional changes upon exposure to heat. Enter the FST-01 Film Free Shrink Tester, a pivotal tool designed to measure the unrestrained linear thermal shrinkage of plastic films and sheets. Let's delve into its significance and application.
Background:
Plastic films and sheets, integral to various industries including packaging, food, and medicine, undergo meticulous production processes. The FST-01 Film Free Shrink Tester addresses the critical aspect of shrinkage, offering insights into process consistency and material characteristics. By understanding the shrinkage behavior, manufacturers can fine-tune production parameters, ensuring precise fit and quality in end products.
Application:
The FST-01 Film Free Shrink Tester facilitates precise measurement of material shrinkage under specified temperatures. This aids in simulating real-world conditions, enabling manufacturers to anticipate dimensional changes post-heat exposure. Industries relying on accurate shrinkage data benefit from enhanced quality control and process optimization, ultimately bolstering product integrity.
Test Process:
The test procedure involves temperature setup, specimen preparation, submersion, and time monitoring. With its advanced features such as precise temperature control and high-precision timer, the FST-01 ensures accurate and reproducible results. Upon completion, the unrestrained linear shrinkage percentage is calculated, providing valuable insights into material behavior.
Technical Features:
The FST-01 boasts an array of technical features, including precise P.I.D. temperature control, high-precision timer, and alarm capability. Consistent fluid medium heating, complemented by the inclusion of standard accessories like a square metal clamp and free shrink holder, enhances usability and versatility. Moreover, equipped with an oil bath cover, the FST-01 adheres to ASTM D2732 standards, ensuring reliability and conformity to industry benchmarks.
Standard: ASTM D2732
Main Parameters
Sample Size 160 mm x 160 mm
Temperature Range Ambient ~ 200C
Accuracy ±0.3C
Dimension 37*44*28 LWH cm
Power Supply 220V 50Hz
FTT-01 Thickness Tester
Background
Ensuring precise plastic film thickness is paramount for maintaining product quality, functionality, cost-effectiveness, regulatory compliance, and customer satisfaction across various industries. Consistent thickness guarantees reliable performance, adherence to industry standards, and minimization of material waste. Any deviations can result in defects, increased production costs, and potential legal or quality issues, particularly in packaging and medical device sectors. Hence, precise thickness measurement is indispensable for plastic film manufacturing and quality control.
Application
The FTT-01 Thickness Tester employs a mechanical scanning technique to accurately measure the thickness of diverse materials, including plastic films, sheets, fabrics, textiles, membranes, paper, foil, wafers, and more. During the process, a sample is placed on the instrument's base, and a weighted presser foot is gently lowered onto it. Subsequently, the instrument measures the displacement or gap between the base and the presser foot, providing an accurate measurement of the specimen's thickness. This method is invaluable for quality control and material assessment in industries where precise thickness measurements are vital.
Standards
The FTT-01 Thickness Tester adheres to several industry standards, including:
- ASTM D374-99: Standard Test Methods for Thickness of Solid Electrical Insulation
- ASTM D1777: Standard Test Method for Thickness of Textile Materials
- ISO 3034:2011: Corrugated fiberboard-Determination of single sheet thickness
- ISO 534-2011: Paper and board-Determination of thickness, density, and specific volume
- ISO 4593: Plastics; Film and sheeting; Determination of thickness by mechanical scanning
Technical Features
1. Controlled by a PLC and operated through an HMI touch screen.
2. Equipped with automatic presser foot lifting for enhanced efficiency.
3. Provides real-time display of maximum, minimum, average, and standard deviation measurements.
4. Capable of storing test results and micro printing for comprehensive documentation.
5. Offers an RS232 port with software compatibility (optional) for seamless data management.
6. Allows for both manual sample feeding and optional automatic feeding for added convenience and flexibility.
Main Parameters
Test Range: 0~2mm(Customization available)
Resolution: 0.1 �¼m
Standard Measure Head: Hemispherical type
Optional Measure Head (flat foot):
50 mm² , 17.5±1 KPa (for film)
200 mm² , 50±1 KPa (for paper)
Power: AC 110~220V
In the dynamic landscape of the beverage industry, maintaining optimal carbonation levels is paramount to delivering products that captivate consumers' taste buds. Enter the CLRT-01 Carbon Dioxide Volume Tester, a pioneering instrument meticulously designed to uphold beverage quality standards and elevate sensory experiences.
Gauging Carbonation Levels with Precision
At the heart of beverage perfection lies the accurate assessment of carbonation levels, and the CLRT-01 excels in this endeavor. By seamlessly integrating automated processes with advanced technology, this tester unveils the intricate relationship between pressure and temperature, shedding light on the nuances of carbonation dynamics.
Automated Efficiency
Bid farewell to manual testing procedures as the CLRT-01 streamlines the entire assessment process. From piercing the bottle cap to vigorous shaking and recording stabilized pressure, every step is meticulously executed with precision. Through PLC control and an intuitive HMI touch screen interface, operators can effortlessly navigate the testing procedure, ensuring consistent and reliable results with every analysis.
Technical Feature
The CLRT-01 boasts a myriad of technical features geared towards optimizing efficiency and accuracy:
1. Industrial-Grade Stability: Precise PLC control ensures unparalleled stability in operation.
2. Servo Motor Mechanism: Agitation of sample bottles is achieved with utmost precision through a servo motor and gearbox transmission mechanism.
3. Anti-Leak Design: Integrated anti-leak features guarantee secure testing conditions, preserving the integrity of results.
4. Customizable Parameters: From piercing speed to shaking frequency, every aspect of the testing process can be tailored to suit specific requirements.
5. Real-Time Monitoring: Accurate temperature and pressure measurements, coupled with real-time display capabilities, provide instant insights into test progress.
6. Versatile Compatibility: Whether testing bottles or cans, the CLRT-01 is designed to accommodate various packaging formats with ease.
Elevate Your Beverage Production
Incorporating the CLRT-01 Carbon Dioxide Volume Tester into your quality assurance protocols promises more than just accurate results; it signifies a commitment to excellence in beverage production. With its unparalleled efficiency, versatility, and precision, this instrument empowers manufacturers to craft beverages that resonate with consumer preferences, ensuring satisfaction and brand success.
Main Parameters
Test Range 0~1MPa
Resolution 0.01KPa
Shaking Speed Adjustable
Piercing Speed 5mm/s (other available)
Sample Height 350mm (other available)
Temp. range 0 ~ 30
Shaking time 40s (other available)
Resolution 0.1
GFT-01 Flex Durability Tester
Background
A pivotal characteristic of flexible barrier materials is their resistance to repetitive strain, commonly referred to as flex durability or Gelboflex resistance. A strong resistance to flex cracking is paramount as it reduces the likelihood of package perforation during distribution, thus ensuring package integrity.
Application
The Flex Durability Tester, also recognized as Gelboflex, evaluates the capability of materials such as films, composites, and coating films to endure repetitive strain. It quantifies flex failure by identifying potential pinholes in the sample structure. Optimal flex crack resistance is crucial as it diminishes the possibility of packaging developing perforations during distribution, thereby upholding the package's integrity throughout its journey. This aspect is indispensable for safeguarding the contents within.
Standards
Our Flex Durability Tester adheres to the ASTM F392 standard for assessing the flex durability of flexible barrier materials.
Sampling and Motion
Within the Flex Tester, a sample measuring 200 by 280 mm is securely fastened to the mandrels. The flexing process entails a combination of twisting and horizontal compression, subjecting the film to these actions repeatedly. Specifically, the setup initiates a twisting motion spanning 440 degrees within the first 90 mm of the stroke, followed by a linear horizontal motion of 65 mm. This entire cycle operates at a speed of 45 cycles per minute.
Users can choose from five pre-programmed test conditions:
- Mode A Full flex for 1 hour (2,700 cycles)
- Mode B Full flex for 20 minutes (900 cycles)
- Mode C Full flex for 6 minutes (270 cycles)
- Mode D Full flex for 20 cycles
- Mode E Partial flex for 20 cycles
Technical Features
Our system boasts PLC control complemented by an intuitive HMI touch screen interface. It offers five standard test modes and encompasses four test stations. Users benefit from the ability to swiftly switch between long and short stroke modes. Furthermore, the system facilitates the selection of test conditions A, B, C, D, and E. Additionally, it features a microprinter for seamless data output.
Main Parameters
Flex Frequency 45 /minute
Flex Angle 440 (90 mm) or 400 (80 mm)
Capacity 2.5 N.m
Horizontal Stroke 155 mm or 80 mm
Stations 4
Sample Size 280 mm x 200 mm
Power 110~220V
GST-01 Gel Strength Tester
Significance of Gel Strength Testing
Gel strength stands as a pivotal quality parameter across diverse industries, particularly in sectors like food production. Notably, in the realm of surimi processing, gel strength serves as a decisive factor governing the texture and excellence of surimi-derived products such as imitation crab meat. This metric significantly influences the mouthfeel, solidity, and overall sensory experience of the product.
Understanding Gel Strength gcm
The evaluation of gel strength is a procedural necessity, especially within food sectors like surimi processing. At its core, the gel strength test is aimed at scrutinizing the texture and caliber of gels, predominantly within industries reliant on gel-based products.
Purpose: The gel strength assessment gauges a gel's capacity to endure deformation when subjected to an external force. This evaluation method is frequently employed to ascertain the texture and uniformity of gels, particularly those formed from proteins present in surimi (a paste derived from fish or meat).
Principle: During the test, a punch probe, possessing specific dimensions, compresses the surface of a gel specimen at a constant rate of deformation until puncture occurs. Typically, a speed of 60mm/min and a probe diameter of �?5mm are utilized. Gel strength is derived from force multiplied by distance, thus denoted in "gcm."
Technical Features of GST-01 Gel Strength Tester
The GST-01 Gel Strength Tester boasts industrial-grade stability facilitated by PLC control, alongside intuitive HMI touch screen operation.
Key Features:
- Equipped with a 7-inch HMI touch screen, ensuring user-friendly navigation.
- Incorporates a precision ball lead screw mechanism for meticulous speed and displacement control.
- Custom-designed program offers flexibility in executing gel strength tests.
- Multiple fixtures enable diverse texture analyses.
- Safety prioritized with features like travel limit protection, automatic returning, and load cell protection cover.
- Offers a range of test items including weight, peak, and distance measurements.
- Features a dot matrix microprinter for comprehensive documentation.
- Optional RS 232 port and professional software facilitate advanced data management.
Test Items Covered:
- WEIGHT: Measures distance at a specified load.
- PEAK: Evaluates gel strength.
- DISTANCE: Measures load at a specific distance.
Main Parameters
Test Range: 0-50N (or as required)
Stroke: 110mm (without probe)
Test Speed: 1~100mm/min
Displacement Accuracy: 0.01mm
Accuracy: 0.5% F.S.
Control: PLC and human machine interface
Output: Screen, Microprinter, RS232(optional)
BST-01 Ampoule Breaking Tester
Background:
Ampoules serve as vital containers for pharmaceutical substances, sealed hermetically by melting the thin top with an open flame. The breaking force of the neck is pivotal, impacting both the safety of the pharmaceuticals and their clinical utility.
Application:
The Ampoule Breaking Strength Tester quantitatively evaluates the breaking strength of ampoules, specifically measuring the force required to rupture the neck.
**Standards:**
This equipment adheres to various standards such as ISO 9187, GB 2637, and YBB00332002, ensuring testing consistency and reliability.
Test Process:
During testing, an ampoule sample is positioned on fixtures, and the pressing head, driven by the power system at a speed of 10 mm/m, determines breaking strength using a high-precision load cell upon contact with the ampoule neck.
Technical Features:
The BST-01 Ampoule Breaking Strength Tester stands out with its versatility and advanced features, applicable not only in pharmaceutical and medical sectors but also in various industries. Its technical prowess, including constant displacement rate, industrial-level stability, PLC control, stepper motor precision, and safety measures, makes it indispensable for testing requirements such as compression, cap opening, syringe gliding force, puncture, and stopper penetration.
The device boasts a PLC control unit, an HMI touch screen, and a precision ball-lead screw-driven stepper motor for accurate speed control. Safety features include a collecting tube for broken samples and a protective cover to prevent sample displacement during testing.
Additional characteristics include:
1. Test fixtures available in various capacities (1ml, 2ml, 5ml, 10ml, and 20ml), accommodating diverse specifications.
2. Multiple fixtures for testing different materials used in medical packaging.
3. Incorporation of a limiting device and an automatic return function.
4. Adjustable test speed catering to different requirements.
5. Dot matrix microprinter for result documentation.
6. Provision of a protective cover for enhanced safety.
7. Optional RS 232 connectivity and professional software for added functionality.
Ensure the BST-01 Ampoule Breaking Tester meets your specific industry needs with its comprehensive features and precise testing capabilities.
Main Parameter
Test Range 0~200N (Or as required)
Speed 1~500mm/min
Resolution 0.1N
Accuracy 0.5% F.S.
Power 110~ 220V 50/60Hz
Introduction:
Understanding and managing the coefficient of friction (COF) is vital in optimizing packaging processes across various industries. The COF-01 Coefficient of Friction Tester provides comprehensive solutions for precisely measuring COF, ensuring efficient performance and quality control throughout packaging operations.
Background:
The COF signifies the degree of friction between surfaces, influencing the ease of sliding between materials. In packaging, maintaining an optimal COF is crucial for smooth processing and minimizing issues during packaging creation, transportation, and storage. Various factors such as additives, treatments, and materials composition affect COF.
Application:
The COF-01 Coefficient of Friction Tester is versatile, catering to a wide range of materials including plastics, rubber, paper, and more. It adheres to industry standards such as ASTM D1894, ISO 8295, TAPPI T816, and GB 10006, ensuring accurate and reliable results.
Formula:
COF is calculated by dividing the force required for sliding by the perpendicular force between surfaces. The tester measures both static (�¼s) and kinetic (�¼d) COF, crucial for assessing stacking, cartoning, machinery processing, and other packaging scenarios.
Technical Features:
1. Advanced PLC control and HMI touch screen interface ensure user-friendly operation and stability.
2. Precision stepper motor and ball lead screw drive mechanism guarantee accurate testing.
3. Real-time test curve display and automatic result recording enhance efficiency.
4. Measures both static and kinetic COF for comprehensive analysis.
5. Compliance with multiple industry standards ensures reliability.
6. Integrated dot matrix microprinter for convenient data output.
7. Aluminum construction of the test plane ensures durability.
8. Optional professional software and RS232 output for enhanced functionality.
9. Customizable local language display for user convenience.
Main Parameters
Load Cell 5 N(or as required)
Accuracy 0.5 F.S.
Sled 200 ±1g (or as required)
Sled Size 63.5mm*63.5mm (or as required)
Test Speed 100mm/min (ISO), 150mm/min (ASTM)
Dimensions 540mm(L)*380mm(W)*240mm(H)
Weight NW 21kg
Power 110~220V 50/60Hz
FDT-01 Falling Dart Impact Tester
Background:
Assessing the impact strength of plastic films is critical for evaluating their quality and durability, particularly in industries like packaging, food, and beverage where transportation and handling can subject materials to significant stress. The Falling Dart Impact Test is a well-established method for precisely measuring this parameter. It involves dropping a dart onto a film surface under controlled conditions to determine the energy required for failure. This test provides essential insights for manufacturers and quality control teams, guiding decisions on material selection, product design, and packaging to ensure optimal performance.
Application:
The FDT-01 Falling Dart Impact Tester is specifically engineered to evaluate the resistance performance of various materials, including plastic films, sheets, composite films, foils, and paper, provided their thickness is less than 1mm. This test aids in gauging a material's ability to withstand external forces, offering valuable data for product development and quality assurance processes.
Standards:
Our Falling Dart Impact Tester complies with internationally recognized standards such as ASTM D1709, ISO 7765-1, JIS K7124-1, and GB/T 9639.1, ensuring accuracy and reliability in testing procedures.
Technical Features:
The FDT-01 Falling Dart Impact Tester boasts advanced features for precise and efficient testing:
1. PLC Control and Touch Screen Operation for stability, user-friendliness, and operational efficiency.
2. Two Test Methods (A and B) catering to diverse testing requirements.
3. Equipped with both Test Button and Foot Switch for safe and convenient operation.
4. Observation Light facilitates easy monitoring of sample status during clamping.
5. Test Results displayed in both Grams and Joules for comprehensive analysis.
6. Utilizes Electromagnetic Suspension and Automatic Falling for accurate and consistent testing.
7. Sample Pneumatic Clamping ensures secure fixation during testing procedures.
8. Dot Matrix Micro-Printer Embedded for convenient data output.
9. Professional Software available as an optional part for enhanced functionality.
Main Parameters
Test Method Method A or Method B (optional)
Test Range Method A: 50~2000g/Method B: 300~2000g
Dart Diameter Method A: 38�±1mm/Method B: 50�±1mm
Impact Height 660mm/1500mm
Accuracy 0.1g (0.1J)
Clamp Pneumatic Clamp
Gas Supply 0.6 MPa �¦8 mm PU Tubing
Specimen Size > 150 mm x 150 mm
Power Supply AC 110~220V 50Hz
Dimension Method A: 500*450*1200 mm (LWH)/Method B: 500*450*2200 mm (LWH)
HTT-02 Hot Tack Tester
Description:
Unlock the potential of your packaging solutions with the HTT-02 Hot Tack Tester, a specialized instrument tailored for assessing hot tack properties crucial in ensuring the integrity of heat-sealed layers. Ideal for industries ranging from packaging and food to pharmaceuticals and beyond, this cutting-edge device offers precise evaluations of seal strength immediately after formation, providing invaluable insights into product performance.
Application:
In vertical form fill and seal (VFFS) processes and beyond, the HTT-02 Hot Tack Tester plays a pivotal role in evaluating the resilience of heat seals under demanding conditions. By accurately measuring the hot tack strength, this instrument empowers businesses to optimize their packaging solutions for enhanced durability and reliability.
Significance:
With the HTT-02 Hot Tack Tester, businesses can address the critical challenge of ensuring robust seals capable of withstanding high loads in rapid packaging environments. By assessing hot tack properties, manufacturers can confidently deliver products that meet the stringent demands of modern packaging standards.
Standard Compliance:
Adhering to ASTM F1921 standards, the HTT-02 Hot Tack Tester offers comprehensive testing methodologies, including Method A and Method B, ensuring consistency and reliability in evaluations.
Principle of Operation:
Utilizing precision-engineered heated jaws and controlled parameters such as temperature, pressure, and contact time, the HTT-02 Hot Tack Tester accurately measures the hot tack strength of thermoplastic surfaces. This principle enables precise assessments of seal integrity under real-world conditions.
Technical Features:
- Industrial-grade stability with PLC control.
- Intuitive 7-inch HMI touch screen for user-friendly operation.
- Precise P.I.D. temperature control for accurate testing conditions.
- Compliance with ASTM F1921 standards, offering versatility in testing methodologies.
- Durable aluminum encapsulated sealing jaws ensure longevity and reliability.
- Advanced features including auto zeroing, overload protection, and adjustable test speeds.
- Optional RS 232 port and professional software for streamlined data management and analysis.
Main Parameters
Sealing Temp. Ambient~250â??
Temp Accuracy �±0.2â??
Dwell Time 0.1~9999s(Heat Seal )
Dwell Time 0.1~9999s(Hot Tack )
Sealing Pressure 0.15MPa~0.7MPa
Sealing Jaws 50mmx10mm Teflon Coated
Jaws Heating Double Heating
Load Cell 200N(Optional:30N50N100N, etc)
Accuracy 0.5 F.S.
Resolution 0.01N
Power 220V, 50 HZ