Features:
1, This product is a new type strong adhesive, applied to indoor and outdoor wall paste of large-scale ceramic tile, grassing stone, natural stone material
2, The indoor ceramic tile adhesive of light steel frame system board, like gypsum board and Eight board
3, Can be used on the low water absorption surface, like paste new ceramic tile above the old ones, and can be used on the firm painting surface
4, Excellent flexibility, can bear the bonding layer stretch that caused by temperature
5, Good anti-infiltration function
6, No need to wet the brick wall, effectively improve the efficiency.
Surface Treatment:
1, The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials.
2, For the new wall, when finding the leveling layer of cement mortar, plaster, should improve the leveling layer of mortar label the cohesive force of the wall, or mix MB-03 slurry additive. Specific reference, please look at the MB-03 introduction.
Operation process:
1, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2
2, Push the ceramic tile or heavy type ceramic tile above it
3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material
4, Can be used for the old ceramic tile re-tread.
Cautions:
1, Never mix the dry slurry with water and use again
2, For the light wall board install large-scale decorative panels, like gypsum board and Eight board, confirm the wall firmness before operation
3, For the painting surface, make sure the initial bond strength and no flake
4, Operating under 5¡æ~40¡æ situation
5, Clean the surface by little wet sponge or cloth before it dry
6, Leave 1.5mm joint space between two tiles, suggesting MB-MC color anti-moldy gap filler.
Technical Reference:
Coverage area(amount) Technical reference
using 3*3mm tooth scraper about 1.7kg/m2 1, adjust time: about 15min (adjust time: the effective time for the dislocation to adjust)
using 6*6mm tooth scraper about 3.0kg/m2 2, cool time: about 10min (cool time: the longest cool time that the adhesive can last )
using 10*10mm tooth scraper about 4.5kg/m2 3, dry time: 24h (according to the weather) 4, water resistance: excellent; non-toxic, prevent fire
the smoother the surface, the less amount 5, when dry, anti-weak acid, anti-strong alkali and oil resistance 6, cut degree: £¾1.2MPa (14days later).
Store Method: Store in cool and dry place, unopened product can be saved for one year.
25kg/bag
Features:
1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones
2, No need to wet the brick wall, effectively improve the efficiency
3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall
4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function
5, Small shrinking rate, no cracking, can be used in cold and humid environment.
Application:
1, The adhesive for cement plaster, brick, smooth cement wall paste stone
2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board.
Surface Treatment:
The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials.
Operation Process:
1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect
2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it
3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material.
Normal Amount:
Coverage areas differ according to the circumstance:
1, using 3*3mm tooth scraper about 1.8kg/m2
2, using 6*6mm tooth scraper about 3kg/m2
3, using 10*10mm tooth scraper about 4.8kg/m2
Note: bricks for wall using 3*3mm tooth scraper or 6*6mm tooth scraper, bricks for floor using 6*6mm tooth scraper or 10*10mm tooth scraper.
Cautions:
1, Make sure the smooth and vertical rate of the surface before operation
2, Never mix the dry slurry with water and use again
3, For the painting surface, make sure the initial bond strength and no flake
4, Finishing after 24h can be walked in or fill the crack.
Store Method:Store in cool and dry place, unopened product can be saved for one year.
25kg/bag
Features:
1. Mixed with cement mortar, improving the bonding strength and flexibility
2. Can be used as booster for the interface treatment agent and tile adhesive
3. Improve the anti-infiltration and waterproof function of cement mortar, and make it suitable for the wet area like swimming pool
4. Anti-aging, non-toxic, safety.
Surface Treatment:
The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials.
Mixed Ratio:
1. For strengthen the bond performance: 50kg cement mortar with 3-5kg additive and appropriate water
2. For outdoor heavy-type ceramic tile adhesive: 5kg mb-01 powder + 1.1kg mb-03 + appropriate water; for indoor heavy-type ceramic tile adhesive: 5kg mb-01 powder + 0.6kg mb-03 + appropriate water; for smooth surface small ceramic tile adhesive: 5kg mb-01 powder + 0.8kg mb0-03 with appropriate water
3. For the interface treatment: 1.0kg mb-01 powder + 0.1kg mb0-03 with appropriate water
4. For the cement mortar leveling: about 2.5kg mb-03 mixed with 50kg cement.
Operation Process:
1. The same operation process with mb-01 adhesive when paste various type of tiles and stone materials
2.Cement mortar leveling: according to the above ratio, mixed the mb-03 with cement mortar, then make inserting
3. Interface treatment: for the high water absorption surface, wet the surface at first, then brush the mixed slurry on the surface, control the thickness under 1.5mm, after it dries, doing the paste; for the low water absorption, no wet work, do with the above
4.for the old ceramic tile:
a.mixing MB-01 with MB-03 in the rate of 1.1-1.2: 1 for the interface treatment
b. after it dries, according to the process using MB-01 to operate directly
c. or use MB-01 directly for the old wall retreating.
Cautions:
1. The mortar that attached to the surface should be clean before it dry
2. Operating under 5¡æ~40¡æ situation
3. Finished after 24h, can be walked or fill crack
4. For the old surface retreating, clean the loosen or flake ceramic tile at first.
Technical Reference:
Coverage area(amount).
Technical reference
1, for ceramic tile and stone:
A, mixed cement about 0.7kg/m2;
B, mixed MB-01 0.4-0.6kg/m2; adjust time(20¡æ): about 10min
cool time(20¡æ): about 10min
2, for interface treatment: about 0.15kg/m2 when dry, anti-weak acid and oil resistance
3, for cement mortar leveling: about 0.1kg/m2 Improve the cement bonding strength: 80%(14days).
Store Method: Store in cool and dry place, unopened product can be saved for one year.
25kg/bag
Features:
1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones
2, No need to wet the brick wall, effectively improve the efficiency
3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall
4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function
5, Small shrinking rate, no cracking, can be used in cold and humid environment.
Application:
1, The adhesive for cement plaster, brick, smooth cement wall paste stone
2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board.
Surface Treatment:
The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials.
Operation Process:
1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect
2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it
3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material.
Normal Amount:
Coverage areas differ according to the circumstance:
1, using 3*3mm tooth scraper about 1.8kg/m2
2, using 6*6mm tooth scraper about 3kg/m2
3, using 10*10mm tooth scraper about 4.8kg/m2
Note: the amount is related to the smooth, vertical rate, and thickness of the stone material
Cautions:
1, make sure the smooth and vertical rate of the surface before operation
2, never mix the dry slurry with water and use again
3, for the painting surface, make sure the initial bond strength and no flake
4, Finishing after 24h can be walked in or fill the crack.
Store Method:
Store in cool and dry place, unopened product can be saved for one year.
25kg/bag
Features:
1. This product is a new type strong adhesive, applied to indoor and outdoor wall paste of large-scale ceramic tile, grassing stone, and natural stone material
2. The indoor ceramic tile adhesive of light steel frame system board, like gypsum board and Eight board
3. Can be used on the low water absorption surface, like paste new ceramic tile above the old ones, and can be used on the firm painting surface
4. Excellent flexibility, can bear the bonding layer stretch that caused by temperature
5. Good anti-infiltration function
6. No need to wet the brick wall, effectively improve the efficiency.
Surface Treatment:
1. The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials.
2. For the new wall, when finding the leveling layer of cement mortar, plaster, should improve the leveling layer of mortar label the cohesive force of the wall, or mix MB-03 slurry additive. Specific reference, please look at the MB-03 introduction.
Operation Process:
1. Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2
2. Push the ceramic tile or heavy type ceramic tile above it
3. For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material.
Cautions:
1. Never mix the dry slurry with water and use again
2. For the light wall board install large-scale decorative panels, like gypsum board and Eight board, confirm the wall firmness before operation
3.For the painting surface, make sure the initial bond strength and no flake
4.Operating under 5¡æ~40¡æ situation
5.Clean the surface by little wet sponge or cloth before it dry
6.Leave 1.5mm joint space between two tiles, suggesting MB-MC color anti-moldy gap filler.
Technical Reference:
Coverage area(amount).
using 3*3mm tooth scraper about 1.7kg/m2.
using 6*6mm tooth scraper about 3.0kg/m2.
using 10*10mm tooth scraper about 4.5kg/m2.
Technical reference:
1, Adjust time: about 15min (adjust time: the effective time for the dislocation to adjust)
2, Cool time: about 10min (cool time: the longest cool time that the adhesive can last )
3, Dry time: 24h (according to the weather)
4, Water resistance: excellent; non-toxic, prevent firethe smoother the surface, the less amount
5, When dry, anti-weak acid, anti-strong alkali and oil resistance
6, Cut degree: £¾1.2MPa (14days later).
Store Method:Store in cool and dry place, unopened product can be saved for one year.
25kg/bag.
