Komatsu Diesel , gasoline , lpg & electric forklifts -
Italian SME full-AC controllers, Full-AC import drive unit, Import multifuntion LCD instrument, High-capacity battery. Technical data: 1KG=2.2LB 1INCH=25.4MM Characteristics Model CPDS15 CPDS18 Rated capacity kg: 1500 1750 Load center mm 500 Power type Battery Tyres Super elastic No.of tyres (front/rear) 2/2 Dimensions Lift height mm 3000 3000 Free lift height mm 130 130 Fork size mm 35¡Á100¡Á920 35¡Á120¡Á920 Upright tilt(forward/backward) deg 5/7 Overall Length to fork face mm 2780 2830 dimensions Length to fork face (withoutfork) mm 1860 1910 Wheel width mm 1050 Overall width mm 1070 Height,mast lowered mm 1980 Height,mast extended mm 3945 Height,overhead guard mm 1990 Turning radius(outside) mm 1500 Front overhang mm 360 Right-angle store aisle(pallet800¡Á1200,1000¡Á1200) mm 2860/3060 2910/3110 Performance Travel speed(with/without load) km/h 13.2/14.3 12.8/14 Lifting speed(with/without load) mm/sec 300/470 Lowering speed(with load) mm/sec 450 Max.pulling force KN 14.84 13.08 Grade ability(with load) % 20 19 Weight Service mass(including battery) kg 3100 3260 Load per axle Full load (front/rear) kg 4020/560 4300/640 Without load (front/rear) kg 1540/1540 1480/1740 Chassis Tyres size Front 18¡Á7-8 PR Rear 16¡Á6-8 PR Wheel base mm 1295 Wheel tread Front mm 895 Rear mm 205 Ground clearance £¨full load/without load) Mast mm 80/85 75/85 Frame mm 100/110 Service brake Hydraulic Power unit Battery Electric motor Ironclad plates Voltage/capacity V/Ah: 48/505 Mass kg: 850 Electric motor Traction power kw: 5.5¡Á2 Lift power kw 8:
Streamlined exterior design, Buffer device for transverse steering axle, Overhead dual air filters, Integral hood, effectual in heat insulation and noise reduction. Technical data : 1KG=2.2LB 1INCH=25.4MM Diesel forklift Specification(CPCD40-100) 1 Forklift type : Diesel forklift truck 2 Model : CPCD40 CPCD45 CPCD50 CPCD60 CPCD70 CPCD80 CPCD100 3 Power type : Diesel 4 Rated capacity : kg 4000 4500 5000 6000 7000 8000 10000 5 Load center : mm 500 600 600 6 Lift height : mm 3000~6500 7 Free lift height E mm 150 195 200 8 Fork size : mm 1070¡Á140¡Á50 1220, ¡Á150, ¡Á60 1220, ¡Á150, ¡Á65 1500, ¡Á160, ¡Á75 1500, ¡Á160, ¡Á80 9 Fork spread outside : 300/1200 300/1200 320/2015 420/2144 10 Mast tilt angle(forward/backward) ¡£ 6\12 6\12 6\12 11 Front overhang A2 mm 562 622 700 733 12 Overall dimensions length to face of fork A1 mm 3091 3091 3125 3592 3940 4258 13 Length with fork mm 4182 4182 4216 : 14 Overall width B1 mm 1485 1995 2245 2245 15 Mast lowered height H1 mm 2380 2500 2695 2845 16 Mast extended height H3 mm 4250 4419 4374 4297 17 Overtead guard height H2 mm 2290 2420 2565 2565 18 Min.turning radius R mm 2790 2790 2830 3450 3700 3900 19 Min.right angle aisle width X mm 3415 3415 3460 3090 3310 3540 20 Travel speed(No load/full load) Forward¢ñ km/h 15/14 28/26 28/24 28/22 28/24 21 Forward¢ò 22/20 22 Backward¢ò 15/14 23 Lifting speed(no load/full load) mm /sec 480/450 480/450 480/430 500/330 450/320 480/350 390/280 24 Max.grade ability(no load/full load) ¡£ 20/19 18/17 17/19 20 20 20 25 Max.grawbar pull KN 21 : 26 Self weight : kg 6450 6770 7050 8840 9350 11080 12860 27 Tyres Front : 3.00-15-18PR 8.25-15-14PR 9.00-20-14PR 28 Rear : 7.00-12-12PR 8.25-15-14PR 9.00-20-14PR 29 Tread Front B2 mm 1180 1470 1600 30 Rear B3 mm 1190 1700 1700 31 Wheelbase A3 mm 2000 2250 2500 2800 32 Ground clearance (No load/full load) Mast M mm 145/175 200 205/245 Frame F mm 180/195 323/343 33 Battery : V/AH 2-12V/80AH 2*12/100 2*12/100 34 Engine Model : Chinese Engine/ISUZU 35 Rated output kw /rpm 68/2000 59/2300 82.4/2000 36 Rated torque N.M /rpm 340/1400~1600 /280/1600~1800 353/1650 415/1400-1600 37 No.of cylinder : 6\4 6\6 6 38 Bore x stroke mm 105*125/105*120 102*118/105*125 102*118 105*125 39 Displacement L 6494/4156 5.785/6.494 5.785 6.494 40 Fuel tank capacity L 90 140 140 41 Transimis sions Type : Hydraulic Hydraulic Hydraulic 42 Shift Front/rear : 2\1 2\2 2\2.
Disassembling and assembling is easy Can fit into smaller spaces when disassembled Equipped with wheels on the mast also allow it to be user as a trolley; Light alumium mast, easy for handling. No any hydraulic problem, because it's operated by winch. The best brake function with special design is obvious. Technical data : 1kg=2.2lb 1inch=25.4mm Item/type: Wfh-181, Sw-181, Wfh-227, Sw-227 Capacity q Kg: 181, 181, 227, 227 Load center Mm: 305, 305, 305, 305 Max.Fork height Mm: 2500, 1700, 1250, 1250 Min.Fork height Mm: 90, 50, 90, 50 Fork length Mm: 570, 570, 570, 750 Fork width Mm: 630, 1100, 630, 1100 Net weight Kg: 60, 66, 51. Fork length570. Fork width1100. Net weight66kg.
Smooth travel and lift combine excellent controls to reduces product damages and increases productivity. Lift limit switch operates at maximum lift height to shut off pump motor. A heavy-duty 24-volt electrical system provides good travel and lift speeds. High quality hydraulic pump assures very little noise, maximum efficiency and durability. Drive units is equipped with an electromagnetic brake that is spring applied and electrically released. The brake is activated by the control handle position. The handle is ergonomically designed with a raise, lower and horn button. Speed automatically reduces when driving with the forks at a height of 12" or higher. Small turn radius makes it suitable for narrow passage ways. The CURTIS electronic controller helps provide plenty of low end torgue while in creasing the motor and battery life. Foot pedal reduces fatigue. Built-in charger. Technical data Residual Capacity at different lifting height. 1KG=2.2LB 1INCH=25.4MM Up to h3 mm ACTUAL CAPACITY (Q) kg 2500, 1500, 1000 2900, 1000, 700 3400, 800, 500 Load center distance (C)mm 600, 700 With CURTIS electric control from Germany Equipped with METRLROTA driving wheel and HPI pump unit from Europe. Heavy duty design with top quality mast construction of HOSCH steel from Germany. Identification 1.2 Manufacturer's type designation FL1529 FL1534 1.3 Drive:electric(battery or mains), diesel, petrol, fuel gas, manual electric 1.4 Type of operation:hand,pedestrian,stand ing,seated, order-picker Pedestrian 1.5 Load Capacity /rated load Q (t) 1.5 1.6 Load center distance C mm 600 1.8 Load distance, center of drive axle to fork X mm 677 1.9 Wheelbase y mm 1183 1168 Weights 2.1 service Weight Kg 1020 1120 2.2 Axle loading, laden front/rear Kg 1195/1325 1245/1375 2.3 Axle loadings, unladen front/rear Kg 755/265 826/295 Wheels Chassis 3.1 Tyres: solid rubber, superelastic, pneumatic, polyurethane) polyurethane 3.2 Tyre size, front 250x78 3.3 Tyre size, rear 80x70 1) 3.4 Additional wheels(dimensions) 150x54 3.5 Wheels, number front/rear(x=driven wheels) 1x+2/4 3.6 Track width,front b10(mm) 685 3.7 Track width,rear b11(mm) 390/515 Basic Dimensions 4.2 Lowered mast height h1(mm) 2005 2235 4.3 Free lift h2(mm) 144 - 4.4 Lift height h3(mm) 2814 3314 4.5 Extended mast height h4(mm) 3430 3905 4.9 Height of tiller in drive position min./max. h14(mm) 985/1365 4.15 Lowered height h13(mm) 86 4.19 Overall length l1(mm) 1940 1925 4.20 Length to face of forks l2(mm) 790 775 4.21 Overall width b1(mm) 805 4.22 Fork dimensions s/e/l(mm) 60/180/1150 4.25 Width over forks b5(mm) 570/695 4.32 Ground clearance, center of wheelbase m2(mm) 50 4.33 Aisle width for pallets 1000x1200 crossways Ast(mm) 2162 2147 4.34 Aisle width for pallets 800x1200 lengthways Ast(mm) 2136 2123 4.35 Turning radius Wa(mm) 1480 1465 Performance Data 5.1 Travel Speed, laden/unladen km/h 5.1/5.4 5.2 Lift speed, laden/unladen mm/s 105/170 5.3 Lowering speed, laden/unladen mm/s 100/95 5.8 Max.gradient performance, laden/unladen % 6/12 5.10 Service brake Electromagnetic E-Motor 6.1 Drive motor rating s2 60min kw 1.2 6.2 Lift motor rating at s3 15% kw 3.0 6.3 Battery acc. To DIN, no 3PZS 6.4 Battery voltage, norminal capacity V/Ah 24/210 Others 8.1 Type of drive control MOSFET Control 8.4 Sound level at driver's ear acc.to EN12053 dB(A) 67 1)Single wheel 80x93 .2 Lowered mast height h1(mm) 2005 2235 4.3 Free lift h2(mm) 144 - 4.4 Lift height h3(mm) 2814 3314 4.5 Extended mast height h4(mm) 3430 3905 4.9 Height of tiller in drive position min./max. h14(mm) 985/1365 4.15 Lowered height h13(mm) 86 4.19 Overall length l1(mm) 1940 1925 4.20 Length to face of forks l2(mm) 790 775 4.21 Overall width b1(mm) 805 4.22 Fork dimensions s/e/l(mm) 60/180/1150 4.25 Width over forks b5(mm) 570/695 4.32 Ground clearance, center of wheelbase m2(mm) 50 4.33 Aisle width for pallets 1000x1200 crossways Ast(mm) 2162 2147 4.34 Aisle width for pallets 800x1200 lengthways Ast(mm) 2136 2123 4.35 Turning radius Wa(mm) 1480 1465.
Technical data : 1KG=2.2LB 1INCH=25.4MM Model No. SEN1520, SEN1525, SEN1530, SEN1535, SEN2020 Rated Capacity kg 1500, 2000 Load Center mm 400 Max. Fork Height 2000, 2500, 3000, 3500, 2000 Max. Machine Height 2560, 3060, 3560, 4060, 2560, Fork Length 1000 Fork Width 300-850 Min. Turning Radius 1350, 1450, 1350 Wheel Base 1185 Front-Wheel Distance 316 Lifting Motor v/kw 12/1.5-1.6 Aneroid Battery v/Ah 12/120-150 Charger v/A 12/15 Overall Length mm 1660 Overall Width 865, 930 Overall Height 1580, 1830, 2080, 2330, 1580 Overall Net Weight kg 448, 470, 492, 515.
Supplier: Forklift and handling equipment
Services: Export and after sales
Buyer: Used motorbike
Supplier: Mobile cranes, earth moving equipment, forklifts, steel processing equipment, steels
Supplier: Diesel forklift, electric forklift and warehouse handling equipment
