Construction Equipment
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Construction Equipments
We supply balustrade and its related components like connectors, saddles, pipes end caps in SS201, SS304, SS316, SS316L. Pipes OD42.2mm*2mm. Also available other OD on request. Balustrade shape round, square any other custom designed shape. Height about 1060mm. Finish: satin, Glossy.
Product Description: We supply connector in SS201, SS304, SS316, SS316L suitable for pipes OD42.2mm*2mm. Also available other OD on requist. Connectors in round, square any other custom designed shape. Finish: satin, Glossy.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Indian Granite: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing. 1. Indian Granite-Black 2. Indian Granite-Black Galaxy 3. Indian Granite-Black Pear 4. Indian Granite-Coffee Brown 5. Indian Granite-Coral Gold 6. Indian Granite-Jasemine White 7. Indian Granite-River White 8. Indian Granite-Sappahire Blue 9. Indian Granite-Silver Waves 10. Indian Granite-Steel Grey 11. Indian Granite-Tan Brown 12. Indian Viscon White 13. Indian Granit-Aspen White
Indian Granites: Indian Granite: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing. 1. Indian Granite-Black 2. Indian Granite-Black Galaxy 3. Indian Granite-Black Pear 4. Indian Granite-Coffee Brown 5. Indian Granite-Coral Gold 6. Indian Granite-Jasemine White 7. Indian Granite-River White 8. Indian Granite-Sappahire Blue 9. Indian Granite-Silver Waves 10. Indian Granite-Steel Grey 11. Indian Granite-Tan Brown 12. Indian Viscon White 13. Indian Granit-Aspen White
Indian Granite Black: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing.
