Gypsum powder(Plaster of Paris) or the hydrated calcium sulphate come in various varieties. However, the best quality is found in the bedded deposits. Then, the balance of the other components makes the quality reliable and helpful in multiple uses. Hence, choosing the right Gypsum Powder Suppliers & Manufacturers in India is a must if you desire the standard excellence. we use the most quality Gypsum in our production. The process includes the high-tech machinery procedure along with the manual checks conducted by our experts. This way, we ensure that the best version of our Gypsum power goes out in the market. In terms of availability, we never let you down as well. Our products are provided all over the country. Hence, no matter where you are, the needed quantity will be available for you. Even if you want a large quantity, Trimurti products serve you well. Our Gypsum powder comes in multiple package sizes that make it easier for you to pick the suitable package required.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
The Ground Granulated Blast Furnace Slag (GGBS/GGBFS) is a type of eco-friendly green building material and high quality secondary cementitious material for concrete and cement. It is recognized as one of the best secondary cementations material for building high durable concrete stricture in the world today! GGBS has taken over a top place of high-performance cement and concrete mineral additives with its unique characteristics of hydration, low-price raw material. GGBS is obtained by quenching molten iron blast furnace slag (a by-product of iron and steel making) in water or steam. It is then further grounded into the desired fineness in terms of the required particle size distribution. The main components of blast furnace slag are CaO (30-50%), SiO2 (28-38%), Al2O3 (8-24%), and MgO (1-18%). The other important aspect of GGBS is its superiority in concrete durability which extends the lifespan of buildings from fifty years to a hundred years. APPLICATIONS Soil stabilization Mortar Used in combination with Portland cement Pre-cast concrete Ready mix concrete Specialist projects
Cement mortar is basically a mixture of cement, sand & water. It is used in various aspects of civil engineering works such as masonry, brickwork, plastering, flooring etc. There are two types, dry mortar and wet mortar. Dry Mortar primarily constitutes of only sand and cement. For price, specifications and other details please contact us.
This versatile product is widely used in construction, art, and medical applications, offering excellent workability and setting properties.
95% purity with 150 mesh fine Gypsum powder Extra white color. Plaster of paris made of SINAI gypsum ore.
Zahret Sinai produces high quality and super fine gypsum powder. We offer it in various setting time and as per customer requirements.
Compressive Strength : 2.72 kg/cm2 Bulk Density : 640 kg/m3 Initial Setting Time : 10 Min