Dissolution tester
Particle size range: 2¬ªm-100¬ªm Channels: 8, defined between 2¬ªm-100¬ªm Sample volume: 0.5-9ml, 10-100ml, entire volume Sample flow rate: 5ml/min-25ml/min Sample volume accuracy: ·+f+1% of selected volume Sensor resolution: ·+10%(usp) Concentration limit: 10000 particles/ml (5% optical coincidence) Repeatability: rsd·+2% (particle counts are more than 5000 particles per sample volume) Power supply: 85-265v, 50hzf+1%, ·+80w Environment temperature: 10f¦-40f¦
Particle size range: 2¬ªm-100¬ªm Channels: 8, defined between 2¬ªm-100¬ªm Sample volume: 0.5-9ml, 10-100ml, entire volume Sample flow rate: 5ml/min-25ml/min Sample volume accuracy: ·+f+1% of selected volume Sensor resolution: ·+10%(usp) Concentration limit: 10000 particles/ml (5% optical coincidence) Repeatability: rsd·+2% (particle counts are more than 5000 particles per sample volume) Power supply: 85-265v, 50hzf+1%, ·+80w Environment temperature: 10f¦-40f¦
Product Introduction: Lightning Protection Element Tester is suitable for testing the DC parameters of over-voltage protection components such as zinc oxide surge arresters (varistor) cermet two three-electrode discharge tubes and vacuum lightning arresters. Product Parameters: Varistor measurement Technical index Measuring range Maximum error Test Conditions
Overview Light digital relay protection tester characteristics 4 6 8 pairs of 100M Optical Fiber Communication Ethernet interface, can send and receive the sampling value of the IEC61850 9 1 2 frame format, Goose, IEEE 1588 packets more support 24 sets of SV packets 64 groups of Goose packets simultaneously 3 5 pairs of 2 10M fiber serial port, can send and receive IEC60044 7 8 FT3, national network expansion FT3, Xu Ji privately owned FT3 frame format sampling value 12 road simulation small signal output, provides testing of protection devices input for small signals Technical parameter Fiber Ethernet port 4 6 8 pairs 100 Mbits S, ST, Mode, 1310nm IEC61850 9 1 2 Le, Goose, IEEE-1588 Send dispersion
Film Shrinkage Test Equipment Film Shrinkage Tester GBK-D1 Film Shrinkage test, known as linear thermal shrink test or free shrink test, is used for analyzing the effect of temperature on heat shrinkable films made from polyethylene, ethylene copolymers and their mixtures. Basically, shrinking force, contracting force and shrinking ratio can be measured in such determination. GBPI Film Shrinkage tester conforms to the multiple national and international standards: ASTM D2732 - Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting ISO 14616 - Plastics Heatshrinkable films of polyethylene, ethylene copolymers and their mixtures Determination of shrinkage stress and contraction stress DIN 53369 - Testing of plastic films determination of the shrinking stress Film Shrinkage Test Equipment GBK-D1 is used to determination of the degree of unrestrained linear thermal shrinkage and dimensional stability at different temperatures. Widely used in industries of plastic material, plastic products, petroleum, chemicals, research institute, inspection agency and so on. Principle This tester uses the principle of air heating to connect the tested sample to the tension sensor and displacement sensor. After reaching the maximum shrinkage force, it is placed in an external test environment with an ambient temperature of 23 to cool down. The reference temperature, shrinkage force and displacement are recorded, and the recorded data can be used to determine the optimal shrinkage conditions of the film. Standards ISO 14616, ASTM D2732, DIN 53369
Product description The Transformer short circuit impedance tester comes with an adjustable power output. Regardless of single phase or three phase transformers, only one connection is required, and the instrument can complete the measurement of all winding pairs. The test and connection are simple. Main technical indicators and conditions of use Measurement accuracy voltage, current 0.2 level Power COS 0.1 0.5 grade, COS 0.1 1.0 grade Impedance COS 0.1 0.5 grade COS 0.1: 1.0 grade Voltage measurement range AC 3V 300V Internal power output range voltage 0 250V, current 0 10A Current measurement range AC 0.2A 20A Working temperature 10 50 Working humidity 0 80 Working power supply AC220V 10 50Hz 1Hz Dimensions 360mm 220mm 150mm Weight of the instrument 20Kg Transformer Short circuit Impedance Tester
To test the tensile strength, peeling strength, heat sealing strength, tearing strength, piercing strength, compression strength, bending strength, and cutting strength of the plastic film, composite film, tape, soft packaging material, rubber sheets, paper, non-woven fabrics, and other packaging materials, widely used in industries of plastic films, food, pharmaceuticals, inspection agency, research institute, college and so on.