Machine feature: The machine uses the below winding design, miniature precision adjustment is more simple and easy , special winder structure design makes winding better.This machine, design of 32 bit, controller chip, , it,ll be faster and higher reliability.In, chinese and english, display, easy to operation, winding, data retention, after power failure, , not, to discarded products,all the parts for this machine are imported prats, such as:japan bearing (nsk,ntn), japan bando belt japan gates belt taiwan ball screw (tbi)taiwan transducers and so on.Four spindle, synchronous design, , uses the , cast iron body, , high speed, , low noise, , small size, is the preferred product assembly line. Function and feature Using the latest, synchronization, with the, coupling, cable, controller. 2with self, detection, , including, setting error, , speed, tracking and velocity, calibration. Optional, lifting, speed of main spindle. 1with ruler function can be easily measured width and start point. Start, moving, speed of the, spindle motor, to, climb time, to decide by yourself. Specifications Spindle number4 Wire size range0.04-0.45mm Loop diameter90mm The max wire spacing9.99mm Winder width100mm Spindle pitch165mm Max speed6000turn/min Spindle motorthree phase motor+inverter phase motor+ac drivers Winder motorstepping motor Input power220v, 50hz/60hz Machine size900460600mm Package size980670680mm Net weight85kg Gross weight100kg
Machine feature: This machinedesign of 32 bitcontroller chip, it will be faster and higher reliability. In chinese and englishdisplay, easy to operation, windingdata retentionafter power failure, notto discarded products. All the parts for this machine are imported prats, such as:japan bearing (nskntn), japan bando belt japan gates belt taiwan ball screw (tbi)taiwan transducers and so on. Heavy body architecture, winding process to make products more stable, four synchronous design, high speed, low voice, small size, is the preferred product assembly line. Function and featur Using the latestsynchronizationwith thecouplingcablecontroller. With selfdetection, includingsetting error, speedtracking and velocitycalibration Optionalliftingspeed of main spindle. With ruler function can be easily measured width and kai winding around the point. Startmovingspeed of thespindle motortoclimb timeto decide by yourself. Application range Ee transformer, ei transformer, stepping motor, relay, coil class, auto abs, switch power transformer and special products -
1. Winding machine nailed one three reliable, enhance space utilization, No problem mixing traditional aluminum jonits and reduce labor and material costs. 2. Mechanical transmission system using double servo motor, The main shaft and the reel servo positioning device. To ensure the quality and stability. Needle distance and the guide for the establishment of the excellent. Fast. High productivity. 3. The machine adopts the famous desigh of the circuit control programmable PLC, the nailed, winding length of the speed with text display setting, fault display directly. Expedient setting operation. 4. The machine can choose cleaning device can absorb the foil foil ash trail, another option that can detect short-circuit testing organization within the short sub-prime. 5. Structure of double of four electrolytic paper, high aluminum foil overlap. Volume electrolytic paper can be 1 to 3 laps. Is the machine of high pressure products for the best. 6. Guide wire nail machine negative foil flat on the department is adding a layer of aluminum foil before(10-16mm), capacitor in a dynamic work to improve plywood box
Main technical parameters Model VOL-260 VOL-300 VOL-400 VOL-500 Diameter range of windable eletromagnetic wire 0.5-1.5mm 0.5-2.6mm 0.5-3.2mm 0.5-3.2mm Min inner diameter of winded coils 30mm 50mm 60mm 60mm Max outer diameer of winded coils 260mm 350mm 450mm 550mm Max height of winded coils 70mm 100mm 140mm 250mm Max winding rotation speed 100 rmp 100 rmp 100 rmp 100 rmp Machine tool power 0.75kW 1.5kW 1.5kW 1.5kW Max outline sise of machine tool 600x1000x1200 700x1000x1300 700x1000x1400 850x1000x1500 If you want to order, please send the pictures and size of your coils to us. ( include Diameter of wire, Height of winded coil, Inner diameter of winded coil, Outer diameter of coil ). We'll recommend the most suitable one for you. 550mm Coil Width PLC Control HV Automatic Winding Machine For Transformer550mm Coil Width PLC Control HV Automatic Winding Machine For Transformer
1 Product introduction: 1. Suitable for 186502560 cylindrical lithium-ion battery production. 2. It adopts the structure of single winding needle drawing on both sides, and the two sides of the winding needle drive the winding needle synchronously. 3. Manual lead-in of pole piece, automatic winding, automatic needle change, automatic sticking of termination tape and automatic blanking. 4. Active unwinding of two coils of diaphragm with continuous adjustable tension. 5. The software can realize advanced positive plate, advanced negative plate, positive and negative plates entering at the same time, and the parameter setting is simple. 6. The winding speed changes smoothly and the core tension is consistent. Product Name: multi specification, cylindrical, power battery lithium battery semi-automatic single needle winding machine Cell specification: diameter 8mm; height: 25 ~ 55mm (depending on the model and specification, it can be customized according to customer requirements) Winding mode: single winding needle, synchronous needle drawing on both sides Pasting method: vertical Length of electrode lug: the electrode lug extends out on both sides of the battery, the extension length of negative electrode is less than 25 mm, and that of positive electrode is less than 10 mm
Specification: Technical parameters Number of spindles for each machine 2 Winding type Parallel winding Blanking mode Mechanical Maximum winding stroke 180mm Mechanical speed 4000 revolutions/minute Maximum external winding diameter 70mm Rated power 400w External dimension 750*1500*1500mm
Automatic CNC Ceiling Fan Coil Winding Machine (Model CW01) Description 1. This Machine is suitable for ceiling fan stators and winding of simple products of motor stator coils. 2. The controller has automatic factions such as winding, winding displacement , rotation pole , tap , trimming , clamping and so on. Most of these features are mostly optional. 3. Multi-function controller design , easy data setting , permanent storage , automatic speed limit , deceleration at both ends and other functions. 4.Users can change the program as needed to achieve multi-functions. 5.The Power Circuit adopts an improved anti- interference circuit with strong anti interference ability. Application Mainly For the production of coils such as Ceiling Fan , Bldc Ceiling fan and Micro motor stators. Model - CW01 Spindle Number - 2 Spindles Controller Number - 2 Separate station Suitable For Wire - 32-40 SWG Thickness of Winding coil - 8-40MM Electric supply - AC220V , Single Phase ,50Hz Output - 350-400/8hours Machine Dimension - 1300X700X1250 Machine Weight - 350KG Diameter Meter of stator -70-140MM
The machine uses the original imported from taiwan plc and servo motors all in english and chinese touch screen control the whole selection of imported spare parts including: japan bearing (nsk / ntn) japan bando belt taiwan (tbia) ball screw. High speed machine twisting fast low noise accurate position is the best choice for twisted products. Function and feature: Unique winding fixture design dress up fast. Using a touch screen interface easy to set parameters. With twisted features. Installation of disconnection detection devices. Double servo motor control excellence performance , using high-precision magnetic tension device winding is better can save more copper Applicationrange: Various thin wire coil twist coil synchronous motor coil ignition coil and so on Specifications: Spindle number8 Wire size range0.02-0.4mm Loop diameter70mm The max wire spacing9.99mm Winder width50mm Spindle pitch70mm Max speed 0-10000turn/min 0-11000turn/min Max bobbin diameter 75mm Twisted speed3000turn/min Control methodplc ac servo motor and stepper motor drive system Spindle motor750w ac servo motor Winder motorstepping motor Twisted motor400w ac servo motor Winder direction adjustable at both ends Input power220v60/50hz Machine size920*900*1360mm Weight219kg
Wire diameter:1.0 4.0 Max.winding speed:150rpm Max.final coil.O.D: 130 650 Wire spacing:Proportional linkage Min.final coil.I.D: 60 Supply voltage:AC 220V 50Hz Max.finalcoil height:150 Mechanical dimensions:900 600 1350 Controller storage capacity Programs:29 set Weight:240kg
Characteristics: Strong stability, good-looking winding shapes, uniform yarn, and stable tension Uniform pattern, reasonable density, and suitable for various types of yarn twisting, rewinding, and splitting.
