"ISO" in the context of polyisocyanurate insulation typically refers to the insulation material's type or category rather than an acronym. Polyisocyanurate is a type of rigid foam insulation known for its high thermal resistance (R-value) and effectiveness in providing thermal insulation.
XPS Insulation (Extruded Polystyrene): "XPS" commonly refers to extruded polystyrene insulation. This type of insulation is known for its closed-cell structure, providing good thermal resistance and moisture resistance. It is often used in various construction applications, such as insulating walls, roofs, and foundations. B1 Fire Rating: The "B1" component might refer to a fire rating. In some fire classification systems, materials are rated based on their fire resistance, and "B1" could indicate a certain level of fire resistance. For example, in the European fire classification system (Euroclass), B1 represents a material with limited combustibility.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Duct Fabrication
Flexible Duct & Accessories
Silicone GP, Acrylic, Duct, FR
Supplier: Refractory bricks, high alumina bricks, fire clay bricks, sk 34 fire bricks, sk 36 fire bricks, acid resistance bricks,insulating bricks, hfk bricks, cfi bricks, special shaped refractory burner block, refractory tiles, refractory tundish well blocks, refractory nozzle, refractory castables, medium purity high purity castables, low cements castables, refractory mortar, refractory cements, ceramics fiber blankets, ceramics fiber boards, crushed refractory bed materials, bottom pouring sets
Rockwool, also known as mineral wool, is an insulation material made from natural stone or mineral fibers. The density of Rockwool refers to the mass of the material per unit volume, and it is commonly expressed in kilograms per cubic meter (kg/m�³) or pounds per cubic foot (lb/ft�³). The density of Rockwool can vary depending on the specific product and its intended application. Common densities for Rockwool insulation products range from approximately 40 kg/m�³ (2.5 lb/ft�³) to 200 kg/m�³ (12.5 lb/ft�³) or more. The choice of density often depends on factors such as thermal performance requirements, structural support needs, and the specific application of the insulation.
Hothree company is a professional thermal interface materials distributor of BERGQUIST(USA) and DENKA (Japan), which located in Shenzhen China and was established in 2011. We have standing stock for commonly used models , which greatly shortens the lead time for customers.We can provide very competitive price.The commonly models such as: BERGQUIST SP900S,GPVOUS,Sil-Pad900S, Sil-Pad2000, Gap-Pad VO Ultra Soft,Gap-Pad5000S35, Bond-Ply100,HF300P and others are always in stock.
