APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
PT. H.P. Metals Indonesia is an Aluminium Extrusion Manufacturer which was first established in 1995, located in Ngoro Industri Persada in the city of Mojokerto, East Java. For over 25 years, we have offered wide-range of outstanding quality products and services, and has been the global supplier of Aluminium extrusion for Architectural and Building Construction, Electronics and Electrical Parts, Furniture and Automobile Industries, and general profiles. We have grown substantially and became the largest Aluminium Extrusion Company in East Java. Our factory occupies over 65000 m�² of land in Ngoro, Mojokerto, with over 1000 well-experienced workers and expatriates from China & Taiwan. H.P. Metals current annual capacity is 36.000 MT, and we are still planning to expand and keep innovating to provide the best for our customers. With advanced machinery and equipment that are precisely handled by experts, allows us to produce wide-variety of shapes as well as durable finishing techniques. Our in-house tool and die shop is staffed by a team of professionals to assist in customized die designs. Moreover, with a systematically controlled process that allows H.P. Metals to be well-known in on-time deliveries. We are determined to keep improving and always provide high-quality products as well as creating innovative, sustainable & reliable solutions, but most importantly with a fair & reasonable price. Our main products are Alloy 6063, 6061, 6005 and ADC 12, serving the demands of every customers. We also offer sales of billet upon request, contact us for further information.
We can supply Aluminium Extrusion 6063 with a regular quantity of 3000 MT per month.
We are one of the leading industry in aluminium profiles in Indonesia. We are able to supply mill finish, powder coating, anodizing, polishing aluminium and also we are able to work on any fabrication too. Our market is covering Australia, USA, Poland and Canada until today.
1. Mill Finish: We offer high-quality aluminium materials with a smooth and uncoated surface, providing excellent durability and versatility for various applications. 2. Powder Coating: Our company collaborates with reputable suppliers to offer a wide range of powder coating options. This enables us to provide aluminium products with vibrant colors, enhanced protection against corrosion, and exceptional aesthetic appeal. 3. Anodising: We partner with reliable anodizing experts to provide durable and corrosion-resistant aluminium products. Anodizing enhances the material's strength, makes it more resistant to wear, and allows for customization through color options. 4. Fabrication: Understanding that every project is unique, we provide fabrication services to meet your specific requirements. Our skilled team can customize aluminium profiles and components to your exact specifications, ensuring a perfect fit for your project.
We M/s. Galco Extrusions Pv. Ltd., Ahmednagar, Maharashtra are the manufacturer of Aluminium Extruded Profiles & we manufacturer number of different types of Aluminum extruded sections.
We M/s. Galco Extrusions Pv. Ltd., Ahmednagar, Maharashtra are the manufacturer of Aluminium Extruded Profiles & we manufacturer number of different types of Aluminum extruded sections.
We at vimsar products are supplier of all kind of aluminium extrusion section. We also provide the surface finish for all kind of aluminium section.
