DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Wollastonite Wollastonite is one of the most versatile minerals. It is a naturally found mineral that is a mixture of calcium, silicon and oxygen. However, it is majorly found in the regions of Rajasthan, Gujarat and some parts of Tamil Nadu in India The physical properties of Wollastonite include an eclectic needle looking structure which is high in brightness and has superior tones of white. It also has low moisture, oil-absorbing and high thermal stability with less solubility in water. It is low in volatility and has a high melting temperature. Wollastonite has medium hardness with rank of 4.5 on Mohâ??s scale. All of these properties make it an excellent and versatile mineral to be used in industries like plastics, paints, ceramics, construction and adhesives to mention a few. We have majorly focused our supply of Wollastonite mineral on its high-end applications in the ceramics, paints and plastics industries. Within the sphere of the plastics industry, it is a brilliant and less-expensive mineral substitute for fiberglass, carbon fiber and synthetic minerals. It is very much popular in automobile industries, as it can enhance the strength, dimensional stability, and influence resistance of car parts, aiding the manufacturers with lighter parts. Wollastonite is a calcium inosilicate mineral (CaSiO3) that may contain small amounts of iron, magnesium, and manganese substituting for calcium. It's often used in electronic equipment like connectors and computer housings because of its great insulating and fire-resistant qualities. Wollastonite mineral is customized to meet the needs of our clients' industries. Our wollastonite is anti-corrosion mineral that is ideal for paints and coatings sector. Wollastonite can improve the fire strength of ceramic tiles and sanitary ware, as well as reduce cracking and glazing faults, for ceramic manufacturers. Our Wollastonite is an excellent reinforcing filler for cement boards and fire-insulating boards in the building industry. Aryan Tiles is confident in the quality of its Wollastonite minerals. Wollastonite has proven to be the most adaptable material used in various key sectors, and the market for it is constantly expanding.
Application :- The XLPE (Cross Link Poly Ethylene) Power Cables are used under ground as well as over head transmission of power in power plants, industries, projects and all other electrical installations. Features :- Manufactured from bright annealed 99.97% pure bare copper & aluminum conductors. These cables are insulated with XLPE compound. Taped/Extruded inner sheath. Round steel wire / flat galvanised steel grip armoured. The outer sheaths can be PVC, HR PVC, FRLS or FR depending upon the application and requirement. Technical Advantage of XLPE Insulation :- Higher current rating, higher short circuit rating (approx 1.2 times that of PVC), thermosetting in nature, higher insulation resistance (1000 times more than PVC cables), higher moisture resistance, better resistance to surge currents, low dielectric losses, better resistance to chemicals and corrosion, longer service life. Comparatively higher cable operating temperature 90�°C and short circuit temperature 250�°C. Technical Data :- Working Voltage : Up to 1100 V Temperature Range : -15�°C to +90�°C Power Cable Sizes : 1.50 Sq. mm to 400.00 Sq. mm in 2, 3, 3 Copper Control Cable Sizes : 1.50 Sq. mm, 2.50 Sq. mm up to 24 cores. Color Codes : 2 Core Cables - Red, Black 3 Core Cables - Red, Yellow & Blue 3 Core Cables - Red, Yellow, Blue & Black (for Neutral) 4 Core Cables - Red, Yellow, Blue & Black 5 Core Cables - Red, Yellow, Blue, Black & Grey 6 Core Cables & above - Adjacent cores are blue for reference and yellow for direction in each lay Black outer sheath Specification : IS:7098 (Part-1) Packing : 500 / 1000 meters on drums
Application :- The Power Cables are used under ground as well as over head transmission of power in power plants, industries, projects and all other electrical installations. Features :- Manufactured from bright annealed 99.97% pure bare copper & aluminum conductors. These cables are insulated with PVC compound. Taped/Extruded inner sheath. Round steel wire / flat galvanised steel grip armoured. The inner & outer sheaths can be PVC, HR PVC, FRLS, HR-FRLS or FR depending upon the application and requirement. Technical Data :- Working Voltage : Up to 1100 V Temperature Range : -15�°C to +70�°C or +85�°C in HR PVC Power Cable Sizes : 1.50 Sq. mm to 400.00 Sq. mm in 2, 3, 3 & 4 core. Copper Control Cable Sizes : 1.50 Sq. mm, 2.50 Sq. mm up to 24 cores. Color Codes : 2 Core Cables - Red, Black 3 Core Cables - Red, Yellow & Blue 3 Core Cables - Red, Yellow, Blue & Black (for Neutral) 4 Core Cables - Red, Yellow, Blue & Black 5 Core Cables - Red, Yellow, Blue, Black & Grey 6 Core Cables & above - Adjacent cores are blue for reference and yellow for direction in each lay Black outer sheath Specification : IS:1554 (Part-1) Packing : 500 / 1000 meters on drums
Edm wire High accuracy, free of impurities, improving discharge performace, surface quality, easy to thread, improving cutting speed, clean running, outstanding quality, value priced. The specification of the wires are :0.10mm, 0.15mm, 0.20mm, 0.25mm. Spools sizes: p-3, p-5, p-10, din125, din160, din200
Product Description ; Brass Wires ,Coated Wires and Diffused Wires. (USD Or FOB price) : As per LME .Pls Contact Product origin : Indian Key Specifications/Special Features : Electric Discharge Machine - suitable for All EDM machines. Minimum Order Size : 1 MT Packgaing details : Spool: DIN125(3.50kgs) / EP-5(5.0kgs) / DIN160(6.0kgs)
We supply and export wide variety of EMD consumables and parts including Interchangeable common parts, all accessories such as wire guide, power feeder, current supply, roller, nozzle etc for different makers. brass or copper tube electrode, EMD Ion exchange resin, JR3A emulsifying ointment special EDM filter- with high quality-price ratio using imported H&V paper brass wire ,copper wire , Molybdenum wire Miscellaneous. Applicable brands:AGIE Charmilles, SODICK, MITSUBISHI,FANUC,MAKINO,SEIBU, HITACHI,BROTHER,JAPAX,SPM,CHMER,ACCUTEX,EXCETEK,MS-WEMD, etc . large supply ability per month with rapid delivery.
300 Efficiency: 5 micron Pressure: in Coupler: no Replacement for: sodick, fanuc, japax More edm filters http://www.Ankok.Com Dimensions: 340¡Á46¡Á300 One carton pack two edm filters More edm filters http://www.Ankok.Com
Wire edm filter cartridges for agie/charmilles More edm filters http://www.Ankok.Com