Supplier: Saw filters, saw resonators and wafers
Item name:saw filter Type:smd Frequency:1575.42mhz Dimension::3*3mm Packing :smd Dimension::3*3mm
Valve type Eccentric Rotary Type Single Seated Straight Through (VFR) Valve sizes Inches Flangeless type (Wafer) End connection Rating std. ANSI 150, 300 Optional JIS 10K, 20 K Valve Opening Rotation of 600 (Full Open) Gland type Bolted gland Rangeability 100:1 Refer Table 2 Flow characteristics Refer Section Ill Max. Differential pressure Refer Sec IV for selection of actuators Leakage Class Metallic Seat. : Class IV as per ANSI-B 16.104 Soft Seat : (Class VI as per ANSI - B 16.104 Bonnet Body integral type (-60 to + 3500 C) Plug Eccentric rotary open yoke type with wing Standard materials Body Carbon steel (A 216 WCB), Stainless steel (A351 CF8, CF8M) Plug SS 304 (Stellited), SS 316 (Stellited) Seat Ring SS 304 (Stellited), SS 316 (Stellited), SS 304 SS 316 with Teflon Packing V.7132Y (upto 2000 C), Graphoil Actuators Standard Spring Diaphragm Actuator, Pneumatic Cylinder (Double Acting), * Rotary Pneumatic actuator - (optional.) Accessories Pneumatic Actuators Pneumatic positioner, Electro pneumatic positioner, I i P converter, Air Filter regulators, Air lock relay, Electronic position transmitter, Limit switches, Volume boosters, Back up system (for Double acting type actuator), Side mounted Handwheel, Top mounted handwheel (for Spring Diaphragm actuators only) etc. Electrical Actuators Positioner, Position transmitters (4-20 mA/POT), Limit Switches, Torque switches etc.
High quality and good surface quality to meet the updating request of pv development and reduce the production cost. Crystal structuremono-crystalline Crystal method cz Conductance typep Dopant b Dimension125*125ía0.4156*156ía0.4 Diameter ª¦150ía0.4 ª¦165ía0.4ª¦200ía0.4 Crystal orientation ía1 Resistivity( ª+.Cm) 1-3/3-6 Lifetime( ª8s) í²15 Carbon concentration( atoms/cm3 )ín5*1016 Oxygen concentration( atoms/cm3 )ín0.95*1018 125*125 and 156*156
Brand name: sf&hw Place of origin: shenzhen, china (mainland) Type: saw filters Nominal center frequency : 1176.62492 mhz Insertion loss: 1.74.5 db Size: 30*30mm-6pin Package: dcc6c Package type: surface mount Application Low-loss saw component Low amplitude ripple Sharp rejections at both out-bands Usable passband 20.0 mhz Features Ceramic package for surface mounted technology (smt) Rohs compatible Package size 3.00x3.00x1.25mm3 Package code dcc6c Electrostatic sensitive device(esd) Package size 3.00x3.00x1.25mm3 Package code dcc6c Electrostatic sensitive device(esd)
Multicrystalline silicon wafers 1.Material: multicrystalline silicon 2.Growth method: directional solidification 3.Conductivity type: p-type (boron doped), astm f42 4.Oxygen concentration: n 1, 0x1017 at./cm3, astm f 121 5.Carbon concentration: n 1x1018 at./cm3, astm f 121 * oxygen content measurement by astm 1188 and used calculation coefficient for ppm atomic is 4, 9 and and for at/cm3 is 2, 45e+17. 6.Square side: (156.0 0.5) mm 7.Symmetry as per the drawing in the enclosure no. 1 8.Thickness: (200 30) µm, astm f 533 9.Ttv: < 50 µm, astm f657 10.Bow < 50 µm, astm f 534 11.Surface saw damage depth µm < 20 (< 15 typically) 12.Saw traces µm 2 µs, astm f 28 15.Surface: as-cut and cleaned; visible contamination, oil or grease, finger prints, soap stains, slurry stains, epoxy/water stains, cracks are not allowed; edge chips under 1 mm from the edge of the wafer are allowed. . 16.Customer may request to receive reference samples 17.Wafers are being stacked into batches of 50-100 wafers each. Then it is sealed into polyethylene film. Protective paper among wafers is upon customer request. 500 -600 wafers in total are being packed into styrofoam box. Styrofoam boxes are being packed into pasteboard cases. Wafers are being packed in such a manner as to ensure minimal damage to the product during transportation. 18.All polystyrene boxes of wafers are identified with: box number; type of wafer; number of wafers per box; all contributing ingots numbers; thickness of wafers; date of packing / output inspection. Geometry: Square side angle:900, 5 Chamfer: 1, 5 mm0, 5mm at 452
(2" 3" 4", 6",8",12") , (N/P), ( , ) One or tow sides polished IC grade silicon wafers. 25pcs/lot.
We can supply (2" 3" 4", 6") , (N/P), ( , ) IC silicon wafer. 25pcs/lot
We can supply (2" 3" 4", 6",8",12") , (N/P), ( , ) one or two sides polished IC silicon dummy(test) wafers. 25pcs/Lot.
