Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Product name - Steel Grating Finish - Hot galvanized ,Paint, Untreatment (black/slef color) Weld way Automatic pressure resistance welding Usage - Industrial platform, Corridor laying, Ditch cover plate, Fence, etc Thickness - 3-10mm Bearing bar pitch - 20mm 30mm 40mm Cross bar pitch - 50mm 100mm Style - Plain sheet, Serrated sheet, I type sheet
Tape Length 10-20 m Tape Width 20-40 mm Feature Water Proof Adhesive Acrylic Use Carton Sealing Duct Tapes is cloth or scrim-backed pressure sensitive tapes often laminated with polyethylene. Features: Duct Tapes are strong Flexible and very sticky tapes Some have a long-lasting adhesive and resistance to weathering. Usages: Duct Tapes actually designed for sealing ventilation ducts, heavy duty packing, jointing and bundling the metal or plastic parts.
Product Details: Tape Width 60-80 mm Use Carton Sealing Adhesive: Acrylic Foam Tapes are made with single or double sided adhesive coating to meet the customerâ??s requirements Usage: Single sided foam tapes are uses as gaskets, seals or heat or cold insulation in HVAC, automobile, refrigerator, air-conditioner, electronics appliance and electrical panel industries. Special rubber and PU foams are used as ant vibration and sound dampeners in electrical and electronic industries
Packaging Type Roll Usage/Application Sealing Brand SuperStick Pattern Plain Material Type Kraft paper Color Brown Tape Width 20-40 mm, 40-60 mm Feature Water Proof Adhesive Side Single Sided Paper Tapes are available with kraft, crape or any kind of recyclable paper coated with adhesive. Features: Eco friendly Wide color range Good holding power Heat insulation property Usage: Paper Tapes is used in automobile, aircraft manufacturing, appliances manufacturing, HVAC. The paper tapes are used as eco friendly packing, marking and holding application. These paper tapes are also used as insulation in electrical industries
Type Single Sided Feature Heat-Resistant Use Bag Sealing Adhesive Silicone Films Tapes are made with BOPP/Polyester/PVC/LDPE/PTFE film coated with single and double side adhesive layer according to application. Features: Good insulation property, Water and chemical resistant, Longer life and good strength. Usage: Polyester Tapes with single side adhesive coating are used as insulation in electronics and electrical industries. Special adhesive coated Polyester tapes are used as holding tapes in all electronic appliances. PTFE-Teflon coated with silicon adhesive can be used for non stick application in all printing and lamination industries
Tape Width >100 mm Tape Length >50 m Color Silver Use Bag Sealing Adhesive Acrylic Material Aluminium Foil Aluminum Foil Tapes are coated with acrylic or rubber adhesive and available with or without release paper. This foil tapes are available with 25 mic-100 mic thickness. Features: Shiny silver, U.V. resistance Flame, moisture and many chemical barrier Good for harsh Long term outdoor application It has hot & cold insulation property Usage: Widely used in tubes and lead jointing for air conditioner, refrigerator and water heaters. For wrapping on pipes, engines and wires as a heat & water resistance. Used as a static ground application.
Application :- The XLPE (Cross Link Poly Ethylene) Power Cables are used under ground as well as over head transmission of power in power plants, industries, projects and all other electrical installations. Features :- Manufactured from bright annealed 99.97% pure bare copper & aluminum conductors. These cables are insulated with XLPE compound. Taped/Extruded inner sheath. Round steel wire / flat galvanised steel grip armoured. The outer sheaths can be PVC, HR PVC, FRLS or FR depending upon the application and requirement. Technical Advantage of XLPE Insulation :- Higher current rating, higher short circuit rating (approx 1.2 times that of PVC), thermosetting in nature, higher insulation resistance (1000 times more than PVC cables), higher moisture resistance, better resistance to surge currents, low dielectric losses, better resistance to chemicals and corrosion, longer service life. Comparatively higher cable operating temperature 90�°C and short circuit temperature 250�°C. Technical Data :- Working Voltage : Up to 1100 V Temperature Range : -15�°C to +90�°C Power Cable Sizes : 1.50 Sq. mm to 400.00 Sq. mm in 2, 3, 3 Copper Control Cable Sizes : 1.50 Sq. mm, 2.50 Sq. mm up to 24 cores. Color Codes : 2 Core Cables - Red, Black 3 Core Cables - Red, Yellow & Blue 3 Core Cables - Red, Yellow, Blue & Black (for Neutral) 4 Core Cables - Red, Yellow, Blue & Black 5 Core Cables - Red, Yellow, Blue, Black & Grey 6 Core Cables & above - Adjacent cores are blue for reference and yellow for direction in each lay Black outer sheath Specification : IS:7098 (Part-1) Packing : 500 / 1000 meters on drums
Application :- The Power Cables are used under ground as well as over head transmission of power in power plants, industries, projects and all other electrical installations. Features :- Manufactured from bright annealed 99.97% pure bare copper & aluminum conductors. These cables are insulated with PVC compound. Taped/Extruded inner sheath. Round steel wire / flat galvanised steel grip armoured. The inner & outer sheaths can be PVC, HR PVC, FRLS, HR-FRLS or FR depending upon the application and requirement. Technical Data :- Working Voltage : Up to 1100 V Temperature Range : -15�°C to +70�°C or +85�°C in HR PVC Power Cable Sizes : 1.50 Sq. mm to 400.00 Sq. mm in 2, 3, 3 & 4 core. Copper Control Cable Sizes : 1.50 Sq. mm, 2.50 Sq. mm up to 24 cores. Color Codes : 2 Core Cables - Red, Black 3 Core Cables - Red, Yellow & Blue 3 Core Cables - Red, Yellow, Blue & Black (for Neutral) 4 Core Cables - Red, Yellow, Blue & Black 5 Core Cables - Red, Yellow, Blue, Black & Grey 6 Core Cables & above - Adjacent cores are blue for reference and yellow for direction in each lay Black outer sheath Specification : IS:1554 (Part-1) Packing : 500 / 1000 meters on drums
