It uses HDPE as the main raw materials with various additives. Advantage: 1. Excellent flexibility, impermeability and elongation. 2. Good isolation and penetration resistance. 3. Resistant to acid and alkali. 4. Eco friendly. Application: Basement, roof, tunnel, subway, reservoir dam, landfill and sewage plant. â??Specification: 1. Thickness: 1.2/1.5/2.0mm 2. Width: 2000mm 3. Length: 20m
HDPE pre-applied waterproof membrane is made of three layers of materials which are HDPE sheet, hot-melt pressure sensitive adhesive, and isolating material respectively. And the isolating material can be special sand(type S) and isolation membrane(type M) Thickness 1.2mm 1.5mm or as required . Width : 2m or as required Length :20m or as required . Product Properties : 1.Pre-applied full-bonding installation: the HDPE pre-applied membrane sanding surface up temporary fixed on the bottom cushion. Direct binding reinforcement, and then poured concrete. The membrane coated sand layer will combine with it tightly ,no water moving between layers. 2.It has strong self-healing ability and can repair slight construction injury. 3.High strength of elongation, strong breaking tensile strength and good anti-perforation performance . 4..With strong chemical resistance to acid and alkali 5.Integration of self adhesion, waterproof and protection, so that can reduce construction links 6.Wet method construction, no need flat layer, low requirement for the base, not affected by weather and base moisture, it has obvious advantage of constructions in rainy season. 7.The floor board of the building should be constructed with a pre-applied anti-sticking method. This method no need protective layer. 8. one layer can reach level one waterproofing security requirements . Product Application Waterproof and anti-seepage , caverns , tunnels , subway , bridge , water conservancy , dam , basement , landfill , sewage treatment pool ,municipal construction we are qualified direct manufacture withs ISO certificates
Supplier: HDPE waterproofing membrane
polyethylene(PVC) geomembrane, as a high performance waterproof and impermeable material, has many remarkable advantages. Thickness: 0.1mm-3mm Width: 2m-6m Color: Black/White/Other colors Following is our PVC geomembrane Thickness 1.6mm spceifications: Tensile Strength (vertical and horizontal): 20MPa/mm Elongation at Break (vertical and horizontal): 580% Right-angle tearing strength (vertical and horizontal): 180N/mm Water vapor permeability coefficient: Using temperature range: +70â??~ -70â?? Puncture strengthâ?¥360N Water impervious: 100% Root resistance: 100% Difference Between PVC Geomembrane and HDPE Geomembrane PVC geomembrane and HDPE geomembrane have significant differences in physical properties, treatment difficulty, joint treatment, puncture resistance, and resilience to deformation. Physical Properties and Suitable Environment: PVC membrane: relatively soft and easy to bend, suitable for general waterproofing projects, swimming pools, and wastewater treatment, etc. HDPE membrane: has higher strength and wear resistance, suitable for engineering projects with higher strength and durability requirements, such as water conservancy projects and landfills. Handling Difficulty: PVC membrane: Due to its flexibility, we can make seams in controlled factory conditions, typically requiring fewer on-site seams than HDPE geomembrane. HDPE membrane: Handling in cold weather conditions can be challenging and requires sewing outdoors. Puncture Resistance: PVC membrane: It is harder to penetrate than HDPE and has high elongation characteristics, allowing it to adapt to site changes without reinforcement. HDPE membrane: While it has elasticity, it becomes plastic after exceeding its yield point and no longer has elasticity. Deformation Recovery: PVC membrane: Most of the deformation can be recovered, with a high tensile elongation, suitable for engineering projects with larger design strain limits. HDPE membrane: Deformation after exceeding the yield point cannot be recovered, and the material properties will change. We should select the appropriate geomembrane according to the specific project requirements and the use environment. HDPE geomembrane is suitable for projects that require high strength and durability, while PVC geomembrane is suitable for general waterproofing projects and water treatment.
TPO waterproof coiled material, namely thermoplastic polyolefin waterproof coiled material, is a new type of waterproof coiled material made of thermoplastic polyolefin (TPO) synthetic resin combining ethylene propylene rubber and polypropylene with advanced polymerization technology and adding antioxidant, antioxidant and softener. It can be made into reinforced waterproof coiled material with polyester fiber mesh cloth as internal reinforcement material, It is a waterproof product of synthetic polymer waterproof coiled material.
Waterproofing membrane is mainly used in building walls, roofs, tunnels, highways, landfill sites and other places. It is a flexible building material product that can be curled into rolls to resist external rainwater and groundwater leakage. As a non leakage connection between engineering foundation and buildings, it is the first barrier of the whole project waterproofing and plays a vital role in the whole project.
TJ-789 TPO Waterproof Membrane TPO Waterproof Membrane takes TPO elastomer as base material,adding fire retardant filling,anti weathering pigment filling,anti oxidization agent and light stabilizer,through high speed mix,melting extrusion,and calendering into waterproofing sheet material. Firstly developed in the early 20 centuries,it is extensively used for rooftop waterproofing projects under the installation of mechanical fasteners. With the combination of the great anti-weathering of EPDM and the weldability of PVC sheet,it defines the leading position in waterproofing industry TPO waterproof membrane has 0% plasticizer and no chloride,generating zero harmful gas when welding Application: Extensively used for the waterproof projects of industrial and residential buildings and public constructions Installation Guide 1. Substrate Requirements: Clean,no bugle and pointy object 2.Installation Steps(Mechanical Fastener) Substrate Clean Pave PE film Pave Insulation board Pre-applied TPO Mechanical Fasten TPO Hot air Welding TPO Detailed Spots Strengthening Test Check 3. Installation 1) Clean the litters,dust on the substrate 2)Pave a layer of PE film,the overlap uses butyl adhesive tape to glue 3)Pave Extruded polystyrene foam insulation board(XPS),using exclusive fasteners to fasten the board 4)Pre-applied TPO membrane: Lay the TPO membrane on the insulation board in accordance with the snap line,paving direction should be perpendicular with the wave of profiled steel sheet,dispose the loose TOP membrane as the outline on the insulation board. Membrane remains flat and even,overlap is 12cm and appropriate trim is needed 5)Fasten the TPO membrane: Align edge of mark line 30mm install the fasteners and elastics 6)Membrane Overlap: One piece membrane laid on the other,use the automatic hot air welding machine to weld 7) Detailed Spots Strengthening: Trim adequate TPO membrane for detailed spots,use portable hot welding machine weld on the TPO membrane 8)TPO membrane edge treatment: Use batten to fasten the edge along with sealants
TJ 441 Self-Adhered Polymer Modified Bitumen Waterproof Membrane is based on SBS elastmoeric modified waterproof membrane,laminating with a special PET film,which can be categorized into two types--N and PY. N has PE(Polyethylene),PET,and D(Non-PET film with adhesion in double side);PY has PE,S(sand),AL(Aluminum Foil),D;Its characteristics lie in suitable for wet substrate,no need to find flat substrate and painted surface disposal,free torch heat,integrating with the mortar or concrete perfectly. It's safe and environmental protection. Features: Supreme adhesion integrates with the substrate forever with special patent formula Suitable for various substrates enables to lower resource waste massively and save the cost and time Unique operation craft of wet treatment,free from primer,no need of heat melt Size Available Width-3.28ftï¼?1m Length-32.8ft(10m) 49.2ft(15m)65.6ft(20m) Thickness- N(1.2mm,1.5mm,2mm) G (2mm,3mm,4mm) Packaging,storage and shipping Product is packed into rolls with plastic woven bag Avoid sunlight and rain,store it under current and dry. The temperature should lower than 50 ,putting it upright and keep the story less than 2 TJ-789 TPO Waterproof Membrane TPO Waterproof Membrane takes TPO elastomer as base material,adding fire retardant filling,anti weathering pigment filling,anti oxidization agent and light stabilizer,through high speed mix,melting extrusion,and calendering into waterproofing sheet material. Firstly developed in the early 20 centuries,it is extensively used for rooftop waterproofing projects under the installation of mechanical fasteners. With the combination of the great anti-weathering of EPDM and the weldability of PVC sheet,it defines the leading position in waterproofing industry TPO waterproof membrane has 0% plasticizer and no chloride,generating zero harmful gas when welding Application: Extensively used for the waterproof projects of industrial and residential buildings and public constructions Installation Guide 1. Substrate Requirements: Clean,no bugle and pointy object 2.Installation Steps(Mechanical Fastener) Substrate Clean Pave PE film Pave Insulation board Pre-applied TPO Mechanical Fasten TPO Hot air Welding TPO Detailed Spots Strengthening Test Check 3. Installation 1) Clean the litters,dust on the substrate 2)Pave a layer of PE film,the overlap uses butyl adhesive tape to glue 3)Pave Extruded polystyrene foam insulation board(XPS),using exclusive fasteners to fasten the board 4)Pre-applied TPO membrane: Lay the TPO membrane on the insulation board in accordance with the snap line,paving direction should be perpendicular with the wave of profiled steel sheet,dispose the loose TOP membrane as the outline on the insulation board. Membrane remains flat and even,overlap is 12cm and appropriate trim is needed 5)Fasten the TPO membrane: Align edge of mark line 30mm install the fasteners and elastics 6)Membrane Overlap: One piece membrane laid on the other,use the automatic hot air welding machine to weld 7) Detailed Spots Strengthening: Trim adequate TPO membrane for detailed spots,use portable hot welding machine weld on the TPO membrane 8)TPO membrane edge treatment: Use batten to fasten the edge along with sealants
SBS modified bitumen waterproof membrane takes SBS (styrene-butadiene- styrene) thermoplastic elastomer modified asphalt mixed with additives as base materials, using premium polyester (PY), fiberglass (G), fiberglass & polyethylene felt (PYG) as matrix , and adopting sand (S), mineral granule (M), polyethylene film (PE), aluminum foil etc as dip-coat, which is produced by stirring and grinding with special equipment. Features A)Good low temperature flexibility,it has no crack when temperature drops into -20â??;Excellent heat resistance, it has no flow when temperature reaches 90â?? B)Great tensity,prolonged life span,easy to use C)Suitable forâ? and â?¡grade constructional waterproofing project,especially for cold area and the project of frequent structural deformation Size Available â?¢Width-3.28ftï¼?1mï¼? â?¢Length-24.6ft(7.5m) 32.8ft(10m)49.2ft(15m) â?¢Thickness- PY (3mm,4mm,5mm) G (3mm,4mm) APP modified bitumen waterproofing membrane based on APP (atactic polypropylene) or APAO, APO (It is reported that tiring polymer) modified asphalt roofing, high-quality polyester felt, fiberglass mat base for the child, with fine sand and mineral tablets (piece) material, PE film for the cladding material, the use of advanced technology refined plastomer modified bitumen membrane. Features A)Good elongation;Good anti-weathering;Excellent flexibility B)Strong adhesion;High strength;Anti-abrasion and anti-impact C)Superior High and low temperature resistance,especially for hot areas D)Easy to apply,heat-welded;Anti-corrosion,anti-mildew ADVANTAGES â?¢Over 1000 cases in waterproofing projects â?¢Accredited contract observing enterprise â?¢15 years of experience in waterproofing industry â?¢Self-contained production line,sound and completed production management systems â?¢Multiple advanced first-class production devices,laboratories,experienced researching panels â?¢3 years of innovation in production craftmanship and 10 proprietary products Guangdong Tenjoy has two brands of building materials-- Tenjoy,Zolon,fits in the needs of residential construction and industrial construction waterproofing projects,which is specialized in the development,production and sales of waterproofing material,including waterproofing membrane,waterproof coating,waterproofing mortar,lost circulation material, water stop and so forth. Given the strong power in product development,a wide range of measuring instruments,the automatic production line of bituminous waterproofing membrane and macromolecule waterproof coating,water stop,automatic paint mixer and racking machine,we can fully meet the needs of domestic major engineering projects with the annual production capacity of 10 million square meters in waterproof membrane,60 thousand tons of paint,8 tons of waterproof slurry.
