We are one of the concrete pump manufacturers in Korea Brand: SAMIL GIANT in Korea Boom length: 67m 62m 58m 52m 48m 45m 42m 37m 32m 28m 24m 21m Stationary pump, Line pump We are able to send full details if you make an inquiry
We have 2units of Samsung (SD20) brand bulldozers brought from the Korean military. It's in good condition because it was brought from the military.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Aggregates are mixtures of sand, gravel, crushed rock or other bulk minerals used in construction, principally as a component of concrete, and in civil engineering. At CEMENTATION we supply aggregates for a range of core applications, from fill materials to aggregates that can be used in concrete, precast concrete, asphalt and for surface dressing. Aggregate plays an important role in concrete and construction part. We supply quality material which makes durable concrete with higher compressive strength and low permeability having better finish. We can supply a wide range of coarse, fine and blended aggregates in accordance with international standards. We acquire rock mines and stone crushing plants and enable us to fulfil contract of any size. Progressive stages if crushing and screening enable us to produce a range of aggregate sizes (06mm to 65mm) APPLICATIONS Road and Highway surfaces Constructions or Civil work Railway Ballast To make Concrete or Asphalt Filling
- Mixing tank capacity: 5.2m3 - Concrete capacity: 3m3 - Dimension: 4250mm*1900 mm*1800 mm - Weight: 1.650kg - Hydraulic motor: BM 160 Manufactured and shipped from Viet Nam. You sign papers and pay directly to the factory. You can visit factory in Viet Nam.
- Mixing tank capacity: 8.6m3 - Concrete capacity: 5m3 - Dimension: 4800mm*2450mm*1900mm - Weight: 2.630kg - Hydraulic motor: BM 200 Buys signs papers and pays directly to factory in Viet Nam. Product is manufactured in Viet Nam. Buyer can visit factory in Viet Nam
- Mixing tank capacity: 7.0m3 - Concrete capacity: 4m3 - Dimension: 4150mm*2200mm*1900mm - Weight: 2.200kg - Hydraulic motor: BM 200 Buyer signs papers and pays directly to factory in Viet Nam. Buyer can visit factory in Viet Nam.
Daikin Hydraulic Pump PV22 Brand new Made in Japan Quantity 110pcs
Okelcor GmbH offers a complete product range of more than 400.000 aftermarket replacement parts for all common European, Asian and American cars, trucks, busses and construction, agricultural, marine and stationary machinery. By selling genuine spare parts of high quality German, European brands only, Okelcor GmbH guarantees for its customer's satisfaction. Exporting aftermarket spare parts to many different African, Latin American, north American, Europeans and Asian countries by serving as a reliable partner to its continuously growing number of customers. As a native export wholesaler and semi bulk seller, Okelcor GmbH is always taking into account the different requirements of each regional market and customer. From air freights, less than container loads and full container loads of spare parts to bus loads and truck loads, from the warehousing of replacement parts to the collection and assembly / consolidation of spare part consignments, Okelcor GmbH's logistic Partners offers any service required by its international customers.
