Rated load kg 1000
Maximum capacity
9
Boom lift wweight kg 200
Lifting speed m/min 0-50 0-60
Electormotor Model
YZEJ132M(L)-4
Power
kw 152 112
Speed-limiter Model
SAJ40-1.2A SAJ40-1.4
Rated tripping speed m/s 1.2/1.4
Rated automaticload KN
40
Type
gradual
Reducer Model
SWC1 TU68T TU66T
Center distance mm 125
Speed radio
1:12 1:10
Bracking distance m 0.3-1.2
Mast section dimension mm 650 300 1508
Crane cage inner net dimension m 1.8*1.75*2.06
Hoistway dimensions m 2.09*2.5
Free end height of the guide rail frame m 4.5
Direct attached frame Installing interval m/set 4.5
Distance between two embedded parts mm 890-900
Installation dimensions from center of rail frame to building wall mm 300-500
The CAT988 with the 3408 engine is a powerful machine designed for heavy-duty applications, including container handling. Here are some key specifications:
Engine: CAT 3408 DITA (Direct Injection Turbocharged Aftercooled)
The CAT 3408 engine is a V8 engine, meaning it has 8 cylinders arranged in a V configuration.
Net Power: 538 hp (SAE J1349:2011)
Engine Power: 580 hp (ISO 14396:2002)
Gross Power: 588 hp (SAE J1995:2014)
Maximum Capacity: 50,000 pounds (as indicated on the boom arm in the image you provided)
Fuel Efficiency: Features like Economy Mode help save on fuel while maintaining productivity
Durability: Built with advanced filtration systems for extended performance and reliability
Productivity: Superior digging, higher bucket fill factors, and reduced dig times
* PURPOSE
customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system.
BACKGROUND
* Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles.
* GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates.
Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion
* Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected.
APPLICATION
Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
The snow removing equipment is the necessary equipment of snow cleaning for farm,orchard, schools, parks, squares, residential areas, garden, lanes sideways, bridges and other key securing sites and widely used in snow winter. This equipment could improve the efficiency of snow removal, reduce labor intensity, and ensure pepole going out more safety and convenient.
1).The road sweeper can be matched to tractor,wheel loader,forklift,
2).powered by hydraulic output of these machinery,only tractor could be driven by PTO.
3).PP with steel wires brushes.
4).Working width from 1200 to 2500mm
5).Suitable for cleaning road,street,floor and other flat.
*The engine adopts famous brand engine, 100% inspection before delivery.
*The Snow Cleaning Machine adopts full metal jacket design,after oxidation spray,anti-corrosion rust proof,long service life.
*Double LED lamp of operation panel, greatly improving the workers efficiency and safety at night and early morning.
*The Snow Cleaning Machine uses monolithic auger design, low cost of vulnerability consumption and easy replacement.
*The Snow Cleaning Machine has the advantages of fashion appearance,mult functions, light and flexibility,simple operation.
1. Application range of twin shaft forced mixer
Js concrete mixer belongs to forced concrete mixer with double horizontal shaft. It is applicable to middle and small concrete prefabricate component company and industry and civil building engineering such as highroad, bridge, water conservancy, port and dock etc. It can stir hard concrete, plastic concrete, fluidity concrete, lightweight aggregate concrete and mortars. It not only can be used as the single machine, but also can work together with pld burden machine to make up the facility concrete batching plant. Js series concrete mixer has many advantages such as stirred uniformly, compact structure, good shape, smooth running, convenient operation and short cycle time.
2. Main features and advantages of twin shaft forced mixer
the liner of stirring vane material is alloy material with ferromanganese, ferrochrome and ferrovanadium etc which is very wearable. It can stir 50, 000 cube meter material.
the speed of mixing is very quick and high efficiency
the hydraulic system controls the discharging which is safe and reliable.
the strength of spiral stirring arm is very high.
3. Main technical parameters of twin shaft forced mixer
Product modelJs1000
Feeding capacity
Discharge capacity
Productivity
Max material radius(mm)60/80
Matched power kw)59.1
Overall dimensions(mm)5650
Total mass (kg)9000
Packing: nude packing or container
Min order: 5 sets
Delivery period: 30 days
Payment: t/t, 100% irrevocable l/c at sight