We deals in the following products :- 1) PVC Resin 2) Caustic Soda Flakes
Nitrogen - 46% min Moisture - 1% max Biuret - 1% max Prilled - 0.85-2mm Granular - 2-4mm 90-94%min color - Pure White Radiation - Non-Radiactive Free Ammonia - 160pxt ppm max
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
--Application-- 1. Foodstuff Industry - Gum Rosin is firstly converted into hydrogenated rosin, and then used to produce chewing gum 2. Paints & Coating Industry - Rosin is a basic material for paint industry because rosin is easy to dissolve in alcohol,turpentine and others organic solvent. Rosin always is converted to resinate, and then refine with drying oil such as tung oil and mix with volatility solvent to produce various lacquers. Rosin also take important role in producing road coating, rosin firstly converted to rosin malefic ester or polymerized rosin or disproportionated rosin Polyols ester, and then used to make thermoplastic coating for road sign inunction. 3. Metal Processing Industry - Rosin mainly is used as solding aid and metal polishing agent. Rosin is a kind of weak acidity matter, it can remove oxidation film from metal surface and slightly erode the surface of metal, and therefore, lots of solding aid agents contain rosin. 4. Construction Materials Industry - Rosin mainly is used as concrete frothing agent and floor tiling adhesive. 5. Papermaking Industry - Most rosin was applied to papermaking industry as sizing agent. Rosin paper sizing agent can prevent printing oil soaking and dispersing from paper, improves the strength and smoothness of paper; enhances the anti-abrasion of paper. But crystal rosin is unfit for making paper sizing agent due to difficulty of saponification, subsequently makes spot on the paper; sometimes even makes the pipe jam in paper sizing agent producing.
Locust bean gum is a natural hydrocolloid extracted from locust tree seeds. The endosperm of carob seeds are separated from germ and testa by various processes then ground to locust bean gum. Locust bean gum imparts smooth flow properties, freeze- thaw stability and appropriate thickening to a wide range of products. It also improves gel strength when used in combination with K-Carrageenan. Locust Bean Gum provides brightness high viscosity the whitest coloured and highest gel strength. Locust bean gum dissolves completely above 75 C. Usage level : 0.1 â?? 0.9 %. We mainly produce the following Locust bean Gum grades; Locust Bean Gum A-01 (2800 -3000 cps):Top grade Locust Bean Gum suitable for the products where high viscosity and whiteness are important. Locust Bean Gum A-02 (2400- 2600 cps): Medium grade Locust Bean Gum suitable for the products where high viscosity is not very important. Locust Bean Gum A-03 (2000 -2200 cps): Standard grade Locust Bean Gum suitable for the products where both high viscosity and whiteness are not very important.
Crystals Benzoin Siam Crystals
Damar products is still needed throughout the world, it can have significant impact on price increases. We provide this Damar on an ongoing basis and can serve exports to your country
Damar products is still needed throughout the world, it can have significant impact on price increases. We provide this Damar on an ongoing basis and can serve exports to your country. With quality packaging and production processes, making the products we sell have selling points that are not only economical but also safe. With our full support we help you become an importer of the products we sell.
We are supplier and exporter of Ferro Silicon. Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags. Ferro Silicon Ferro Silicon has a melting point of 1200�?�°C to 1250�?�°C with a boiling point of 2355�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
