TC100 / copolymerized hydrocarbon resin is produced with and fraction, which has and strengths.It can replace the expensive C5 hydrocarbon resin in hot melt adhesive and rubber tire fields. In rubber tires, TC100 hydrocarbon resin not only can increase the adhesive force between colloidal particles, but also can enhance the adhesion between the particle and the cord thread.TC100 hydrocarbon resin is suitable for producing high quality rubber products. In adhesive, TC100 hydrocarbon resin have better initial adhesion and it also can adjust the adhesive durability and bonding strength. Product Specification: Item Test Method Unit Specification Range Softening Point ASTM-E28-58 95-105 Color ASTM-D-1544 GC 4Max Insoluble ETM-E-99 Vol% 0.05Max Acid Value ASTM-D-974 Vol% 0.2Max Specific Gravity ASTM-D-71-72A g/ 0.99-1.03 Features of TC100 C5/C9 Copolymerized Hydrocarbon Resin: Wide optional range.It will be more stabilized by the addition of antioxidant.Good compatibility with EVA,SIS and SBS etc. Applications:Hot melt adhesive,Synthetic rubber
Tc100/ copolymerized hydrocarbon resin is produced with and fraction, which has and strengths.It can replace the expensive c5 hydrocarbon resin in hot melt adhesive and rubber tire fields. In rubber tires, tc100 hydrocarbon resin not only can increase the adhesive force between colloidal particles, but also can enhance the adhesion between the particle and the cord thread.Tc100 hydrocarbon resin is suitable for producing high quality rubber products. In adhesive, tc100 hydrocarbon resin have better initial adhesion and it also can adjust the adhesive, s durability and bonding strength. Product specification: Itemtest methodunitspecification range Softening pointastm-e28-58 , 95-105 Colorastm-d-1544gc4max Insolubleetm-e-99vol%0.05max Acid valueastm-d-974vol%0.2max Specific gravityastm-d-71-72ag/0.99-1.03 Features of tc100 c5/c9 copolymerized hydrocarbon resin: Wide optional range.It will be more stabilized by the addition of antioxidant.Good compatibility with eva, sis and sbs etc. Applications:hot melt adhesive, synthetic rubber Package: 25kg kraft paper bag Storage: All resins with low softening point present a risk of solidifying or lump. For softening point less or equal to 110, , we suggest you keep resin in a cool (25, max) ventilated place and avoid direct sunshine.
PG100 resin is a kind of C5 modified C9 resin, with both character of C5 and C9 component, which is designed to tackify a variety of adhesive polymers, including ethylene vinyl acetate (EVA), styrenic block copolymers (SIS, SBS, SEBS), amorphous polyalphaolefins (APAO).
We deals in the following products :- 1) PVC Resin 2) Caustic Soda Flakes
hydrogenated C9 hydrocarbon resin which compete and substitute C5 resin in Hot Melt Adhesive and Road marking paint
product description: C5/C9 copolymer resin is a kind of thermoplastic resin produced by pretreatment, polymerization, distillation and other processes of C5 and C9 fractions produced by petroleum cracking. It is not a high polymer, but a low molecular weight between 300-3000. Polymer. It has the advantages of C5 petroleum resin and C9 petroleum resin. It has the characteristics of low acid value, good miscibility, water resistance, ethanol resistance and chemical resistance. It is chemically stable to acid and alkali, and has the characteristics of good viscosity adjustment and thermal stability. Since the structure does not contain polar groups, it has good water resistance, acid and alkali resistance, weather resistance and light aging resistance. It has good solubility in organic solvents, especially in petroleum solvents, similar to other resins. The compatibility is very good, and it also has brittleness, viscosity increasing, cohesiveness and plasticity. It is generally not used alone, but as an accelerator, regulator, modifier and other resins.ã?? Product application areas: C5/C9 copolymerized petroleum resin is used in hot melt adhesives, synthetic rubber, adhesives, paints, rubber soles, tires, etc., and is suitable for high-demand rubber products such as radial tires. It can not only increase the adhesion between the rubber particles, but also It can improve the adhesion between the rubber particles and the cord. In the field of hot melt adhesives, adhesives, and adhesives, C5/C9 copolymerized petroleum resin can not only provide better initial viscosity, but also can be used like rosin resin. To adjust the durability and bonding strength of the glue and resin mixture. It can be used as a substitute for terpene resin, rosin glyceride, etc.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Nitrogen - 46% min Moisture - 1% max Biuret - 1% max Prilled - 0.85-2mm Granular - 2-4mm 90-94%min color - Pure White Radiation - Non-Radiactive Free Ammonia - 160pxt ppm max
C9 hydrogenated hydrocarbon petroleum resin Chemical name: c9 hydrogenated petroleum resin Physical properties: it is produced through the process of refinement, isolation, polymerization and molding with the raw material of hydrocarbon resin c9 which is the by product from the ethylene fragment. The product is white granular, aromatic resin, which is easily soluble in organic solvents such as benzene and toluene etc. It has good compatibility, thermal stability, light stability, good water resistance and chemical resistance. Product specification: Test item C9 hydrogenation # 100 Test method Appearance White granular Eyeballing Softening point(°c) 95-120 Gb/t4507(ring&ball) Acid value(koh mg/g) =1.0 Gb2895 Color gardner (ga) 0-1 Astmd-1544 Melt viscosity(200°c)cps =400 Astmd-3236 Insoluble (vol%) ------ Ash content
