Supplier: Crude oil, cement, charcoal, flour, palm kernel oil, palm kernel seed, river sand, white beans, bitumen, turkey, parboiled rice, used car, motor oil, diesel
we are wholesale of Portland cement contact us for wholesales price .
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Supplier: Fuel like diesel en590, jet fuel a1, lngg, lpg, copper cathode, a7 ingots, used rails, agri products like sugar, wheat, rice, soyabean etc, sunflower oil, valves & fasteners, spare parts for machineries. construction equipments like concrete machines, crushers, sand washing plants, material handling equipments, and construction materials, coal, diesel, machineries, tyres, generators, tyre shredder machines, fasteners, valves, epoxy, chemicals
Services: Exporter
Aggregates are mixtures of sand, gravel, crushed rock or other bulk minerals used in construction, principally as a component of concrete, and in civil engineering. At CEMENTATION we supply aggregates for a range of core applications, from fill materials to aggregates that can be used in concrete, precast concrete, asphalt and for surface dressing. Aggregate plays an important role in concrete and construction part. We supply quality material which makes durable concrete with higher compressive strength and low permeability having better finish. We can supply a wide range of coarse, fine and blended aggregates in accordance with international standards. We acquire rock mines and stone crushing plants and enable us to fulfil contract of any size. Progressive stages if crushing and screening enable us to produce a range of aggregate sizes (06mm to 65mm) APPLICATIONS Road and Highway surfaces Constructions or Civil work Railway Ballast To make Concrete or Asphalt Filling
Mitsubishi MG400 Motor Grader Specifications Main Specifications Blade Width: 3710mm (standard blade width) Steering System: ATC Weight & Loads Operating Weight: 13,100kg Front Axle Load: 3,700kg Rear Axle Load: 9,400kg Dimensions Overall Length: 8490mm Overall Width: 2400mm Overall Height: 3360mm Wheelbase: 5910mm Tandem Wheelbase: 1520mm Ground Clearance: 355mm Engine Manufacturer: MTB Model: 6D22C Rated Output: 110.3kW (150 PS) @ 2000rpm Cylinders: 6 Bore x Stroke: 130 x 140mm Displacement: 11.2liters Hydraulic System Output Pressure: 17.2MPa Oil Flow Rate: 128L/min Transmission Type: DPS Speeds: 6 forward / 6 reverse Max Travel Speed: 45.0km/h (forward), 45.4km/h (reverse) Tires Front: 13.00-24, 14-ply Rear: 13.00-24, 14-ply Performance & Other Features Operation Type: Hydraulic (HYD) Scarifying Width: 1225mm Minimum Turning Radius: 6900mm Articulate Angle: 25 Fuel Tank Capacity: 230L Optional Equipment: BL(4000), S/C
Supplier: Submersible pump, motor, pipe, cable
Supplier: Micro silica (silica fume), silica, fly ash, pozzolano, ggbfs and white cement, other cementatious materials and factory/plants specialized spare parts & equipments, automation & switchgear, drives & transmission spares, instrumentation & pump, pneumatic & hydraulic spares, valves & actuators, mechanical parts, high carbon ferro chrome, foundry pig iron, iron ore concentrate, chromite ore, antimony ore, silicon metal 441 (powder), ferro silicon (fesi), iron ore pellet, copper concentrate
Static water level depth 40 90 mtr Stroke Length 100 mm + 4 mm Discharge Minimum 300 ml per stroke or 12 Liter /40 stroke completed in 1 minute Bore well Casing Size 100 NB to 150 NB Cylinder - Cast Iron or Stainless Steel or UPVC Rising Main Size 32 NB MS GI Riser Pipe or 40 NB UPVC with 3 piece Coupler or 40 NB UPVC Pipe with SS Nipple and Socket in 3 meter length Above Ground Structure (Pump Stand, Head, Handle, Water Tank etc. -( Mild Steel with hot dip galvanized) Connecting Rod - Mild Steel or Stainless Steel in 3 meter length
