Excel Hydro-Pneumatics Pvt. Ltd.

We are leading manufacturer & Exporter of Brass shower header clamp.

we are leading manufacture & exporter of Brass washer

we are leading manufacturer of Brass Lock washer

We Are Leading Manuacturer Of Brass Anchors

* PHOSCAST
Phoscast : Phosphate Bonded Castables

* PURPOSE
customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system.

BACKGROUND

* Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles.

* GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates.
Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion

* Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected.

APPLICATION
Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

NPK Bulk Blends like 2:3:2 (22), 2:3:4 (30), 3:2:1 (25), 4:3:4 (33), 5:1:5 (36) etc.

Bulk Blend is a physical mixture of several monocomponent (straight) fertilizers. Blending technique helps to tailor chemical composition of final NPK product according to specific requirements, dictated by the soil, crop, technical preferences, etc.
We are flexible to produce any type of NPK blends such as but not limited to well-known grades NPK 10:20:10 (D-compound), NPK 7:14:7, NPK 6:23:23, NPK 10:20:20 and any other upon your request.
We use only best quality raw materials of international standards.

Product introduction:

Calcium is a silvery white metal that is harder and heavier than lithium, sodium, and potassium;

It melts at 815 C. The chemical nature of metallic calcium is very active. In the air, calcium is quickly oxidized and masked with an oxide film. When heated, calcium will burn and emit a beautiful glow of brick red. Calcium and cold water have a slower effect, and intense chemical reactions occur in hot water to release hydrogen (lithium, sodium, and potassium can cause intense chemical reactions even in cold water). Calcium is also easily combined with halogens,

sulfur, nitrogen, and the like.



1,product name:calcium metal

2,Shape :powder, lump and granulates

3,CAS:7440-70-2

4,Density:1.54g/cm

5,Melting point:850C

6,Boiling point:1440 C(lit.)

7,Application:Wheel keel



Product use:

At present, in the steel industry, the main use of metal calcium is to process into metal calcium particles, and then to make calcium iron wire or pure calcium wire, and finally used for steel refining outside the furnace, its role is to desulfurization, deoxidation, increase the fluidity of molten steel. Promote the rapid rise of inclusions in molten steel, generally used in the production of high-quality steel; as a dehydrating agent to produce anhydrous alcohol; in the petroleum industry, as a desulfurizing agent, in the metallurgical industry, it is used to deoxidize or

desulfurize . However, calcium compounds have a very wide range of uses, especially in the construction industry.

Beekeeping Equipment Stainless Steel Honey Press Tool 26.5cm Diameter
Basic Information
Place of Origin:
china
Brand Name:
Super-Sweet
Certification:
ISO
Model Number:
SS-CCM-01
Minimum Order Quantity:
1 set beeswax foundation sheet machine/beeswax embossing machine/beesw
Price:
$200-$1000
Packaging Details:
hot sell honey machine stainless steel bee wax press price with splash collar. Standard Packing: 1.OPP bag 2.Foam box 3.Carton box
Delivery Time:
7-10days
Payment Terms:
L/C,T/T,Western Union,MoneyGram
Supply Ability:
1000 Piece/Pieces per Month Beeswax foundation sheet mold