Supplier: Fire safety equipment, sub station
Services: Import and distribution
Buyer: Surgical face mask
Supplier: Fire alarm manual pull station MCP protection cover
A fire alarm system is a set of electric/electronic devices/equipment working together to detect and alert people through visual and audio appliances when smoke/fire is present. These alarms may be activated from smoke detectors, heat detectors, water flow sensors, which are automatic or from a manual fire alarm pull station. Types of Fire Alarm System: All Fire Alarm Systems essentially operate on the same principle. If a detector detects smoke or heat or someone operates a break glass unit (manual break point), then alarm sounders operate to warn others in the building that there may be a fire and to evacuate. It may also incorporate remote signaling equipment which would alert the fire brigade via a central station. Conventional Fire Alarm System In a Conventional Fire Alarm System, a number of call points and detectors are wired to the Fire Alarm Control Panel in Zones. A Zone is a circuit and typically one would wire a circuit per floor or fire compartment. The Fire Alarm Control Panel has a number of Zone Lamps. The reason for having Zones is to give a rough idea as to where a fire has occurred. This is important for the fire brigade and of course for the building management. The accuracy of knowing where a fire has started is controlled by the number of Zones a Control Panel has and the number of circuits that have been wired within the building. The Control Panel is wired to a minimum of two sounder circuits which could contain bells, electronic sounders or other audible devices. Each circuit has an end of line device which is used for monitoring purposes. Addressable Fire Alarm System The detection principle of an Addressable System (Fire Alarm System) is similar to a Conventional System except that the Control Panel can determine exactly which detector or call point has initiated the alarm. The detection circuit is wired as a loop and multi devices may be connected to each loop. The detectors are essentially Conventional Detectors, with an address built in. The address in each detector is set by dil switches and the Control Panel is programmed to display the information required when that particular detector is operated. Additional Field Devices are available which may be wired to the loop for detection only i.e. it is possible to detect a normally open contact closing such as sprinkler flow switch, or a normally closed contact opening. Fire Alarm System comes with single loop as well as multi loops. It depends on requirement. The items which are integrated with Fire Alarm Systems are given belowâ?¦. Brands are available : AGNI, MORLEY, NOTIFIER, Modern Technologies gives you top class branded Fire Alarm System with affordable price. We also provide installation & maintenance services.
The Notifier NBG-12 Series Pull Station is a fire alarm initiation device that allows manual activation of the fire alarm system. It typically consists of a red or yellow manual-pull handle or lever, which when activated, sends a signal to the fire alarm control panel to initiate an alarm. The NBG-12 series is designed for use in fire alarm systems and is commonly used in commercial, industrial, and residential buildings. The product is known for its durability and reliability, and it meets industry standards for fire alarm systems.
FM200 Fire extinguisher cylinder refill machine Fire extinguisher refilling equipment is specialized machinery and tools designed for the maintenance and recharging of fire extinguishers. These tools and systems are essential to ensure that fire extinguishers remain operational and effective in case of emergencies. Fire Extinguisher Refilling Equipment Fire extinguisher refilling equipment is specialized machinery and tools designed for the maintenance and recharging of fire extinguishers. These tools and systems are essential to ensure that fire extinguishers remain operational and effective in case of emergencies. Features of Fire Extinguisher Refilling Equipment Refilling Stations: Fire extinguisher refilling equipment includes dedicated stations where empty or partially discharged extinguishers can be refilled with the appropriate extinguishing agent. These stations typically have compartments for different types of extinguishing agents, such as water, foam, powder, or CO2. Pressure Testing: Refilling equipment often incorporates pressure testing mechanisms to ensure that the extinguisher's container can withstand the required pressure. This helps identify any structural weaknesses that might compromise the extinguisher's performance. Filling Mechanisms: The equipment consists of mechanisms for precisely filling extinguishers with the correct amount of extinguishing agent. This ensures that the extinguisher will be effective when used.
Supplier: Generator, fire detection system, sub station, window air conditioner
Services: Electrical works as operation and maintenance
Characteristics of Water-based Extinguishing Agent Filled in Fire Extinguisher The premixed water-type extinguishing agent filled is an efficient one that with good fluidity and thermal stability, rapid fire control, high capacity of anti-recrudescence, non-toxic, non-pollution, and 100% biological degradation etc. Main Application The fire extinguisher is mainly used in manufacturing enterprises which produce wood, textiles, rubber and plastics, pedlars' market and coal mines that have organic solids where A-type fires may occur. It can also be applied to airport, dock, station, gas station and oil depot where B-type fires may occur. When filled with anti-soluble AFFF foam extinguishing agent, the extinguisher can also be used in chemical industries of petrochemical aids, paint and alcohol as well as in warehouses storing solar solvent.
Fire extinguishing device is a fire extinshier for textile warehouse. When throw into or rolling to fire, it will explode and make huge noise to catch everyone s attention nearby. You can also place it where the hotchpotch are such as flammable objects, circuit breaker box and gas tank. In case of fire, it will put out the fire by itself thus guarding lives and property. Shape: Ball Type Instruction: Fixed position by automatic fire sensor and / or throw in fire area Ignition: Automatically explode within 3-5 seconds after touch of fire Content: Environmental harmless dry powder Validity: 5Years Automatic reaction time: 3-5Seconds (3-5seconds) Effective extinguish area: (A) 1KG-3cubic meter Specification: 1.Light weight only 1.3 kilograms shape of a ball even the old and children can use it easily. 2.As long as simply roll out to fire scenes or set in the places easy on fire, such as the electric case, the gas barrel, flammable chemical articles in the factory, shopping mall, gas station, hotel, or even in the car. 3. As long as been touched for 3-5 seconds by flame reaching 70 degree C, A.F.O will automatically extinguish the fire effectively and rapidly. 4. You do not need to be close to fire scenes to extinguish the fire any more . A.F.O is made of totally harmless material to the environment and safe for users: the exploding power has been accurately calculated to be approved safe. 5. AFO, it can be always at your service to extinguish the fire and no need to do regular inspection yearly. The product life span is 5 years, and the decibel when extinguishing the fire can be a fire alarm to warn people in the fire scenes.
The electric vehicle fire suppression system family is a family of fire suppression systems that cause fires caused by thermal runaway of the battery in the vehicle. It is a preventable product. Battery thermal runaway accidents are on the rise recently. Product List Electric Vehicle Incident Response Equipment Kerinet - The two doors are deployed in opposite directions, allowing concealment from the flames - Can respond quickly with an internal individually configured anti-gun storage cargo Electric Car Fire Wet Extinguisher - Useful for early response to electric vehicle fires, such as tunnels, underground parking lots, charging stations, etc. - Quickly suppress fire spread Electric car Fire cooling Tube Window - Can expect lower battery cooling effect through pole-shaped injection nozzle - The configuration of the steering handle and wheel allows you to set the injection position on the lower part of the vehicle
