Specifications: W plate can be manufacture according to customer request Owning two hot rolling machine and five cold rolling machines, we can supply tungsten and molybdenum sheet thickness of 0.05mm to 20mm.With very good performance, these products are used to produce electrode, heater ,heat-shield ,sputter target, crucible in electronic, vacuum furnace application. W plate in Max size: Thickness(mm) Width(mm) Length(mm) 1.5-2.0 150 200 2.0-3.0 200 250 3.0-4.0 250 600 4.0-6.0 300 600 6.0-8.0 300 800 8.0-10.0 300 750 10.0-14.0 200 650 >14.0 200 500
Sintered tungsten crucible Sintered with tungsten powder the sintered tungsten crucibles are multi-purpose production in sintering furnace, large crystal growth furnace. Thickness of sintered tungsten crucibles is usually 8-12 mm; diameter is typically 100-550 mm; height is typically 50-700 mm. Such crucible Purity: W �?� 99.95%; density is usually up 18.2g/cm3, by special needs the density can up 18.8g/cm3 or more. Features: 1.The overall density of sintered tungsten crucible is fairy high between 18g/cm3 to 18.3g/cm3; 2.Its chemical purity of sintered tungsten crucible can be above 99.95%; 3.The diameter of sintered tungsten crucible can be above 200mm; 4.The surface roughness of tooled crucibles does not exceed Rz 6.3; 5.The use temperature of sintered tungsten crucible should be below 2450�C in vacuum or deoxidize atmosphere. 6. The shapes and dimensions of crucibles are also made in accordance with customers' requirements. material density size W >99.95% 18g/cm318.3 g/cm3 Diameter: 100-550mm; Height:50-700mm Stamped tungsten crucible The tungsten crucibles can be produced of a tungsten plate by stamping, spinning, or welding. It can be used to produce single-use square or round crucible. Thickness typically 0.5 to 3 mm. Such tungsten crucible Purity: W �?�99.95%; density is usually up 19g/cm3 Forged tungsten crucible The tungsten crucible can be made of tungsten rod by turning , generally they are smaller and with higher density. Usually the wall thickness 3-10 mm; diameter of 80 mm. They are widely used by sintering furnaces for ceramics and other materials or vacuum evaporation coating machine. Purity: W �?� 99.95%; density are usually based on different diameters of up to 18.3 to 19g/cm3 Notice: 1.Before use, it is recommended that the consumer anneal (de-gas) crucibles in a vacuum without batch charging; 2.In a furnace, the annulment process should be supported with a vacuum at P< 10-3mmhg; 3.When preparing a sintered tungsten crucible for work, the consumer should not allow a sharp rise or fall in temperature, or abbreviate the recommended time periods for holding temperatures. Applications Tungsten crucible is mainly used used for rare earth,sapphire single crystal growth furnace , quartz glass, Metal extracting, metallurgical industry, machinery processing, glass and ceramic industries, etc.
1. Tungsten wire tungsten Filament: tungsten wire in spool Model NO.: KK Type: Tungsten Wire Material: W-1 Purity: 99.95%Min. Melting Point: 3410 Ceiclus Boiling Point: 5927 Ceiclus Density: 19.2g/cm3 Diameter: 0.01-2.00mm Surface: Black and Cleaned Export Markets: Global 2. Dimensions and Tolerances of tungsten wire: Tungsten wires diameters are generally expressed in terms of inches or mils (thousandths of an inch). For thin wires from. 001 inches up to. 020 inches in diameter, the diameter of the wire is measured by weight per unit length. That is, the weight expressed in mg of a 200 mm length of wire. The standard diameter tolerance is: � 3% of the weight measurement. Closer tolerances are available, depending upon the application for the wire product. Specification: Diameter, mm Difference between 2 feet, mm Inside diameter tolerance, mm Big heater element Small heater element 0.4-3.0 1 0.3 0.4-1.0 1 0.3 0.4-1.3 1 0.3 0.4-1.0 2 1 0.3 0.4-1.0 1 0.3 0.4-1.0 several stranded coils 0.3 Note: Different diameter and length are available for your 99.95% pure stranded tungsten wire. 3. Straightness of tungsten wire: Wire may be finished in the unstraightened or as drawn condition and is controlled to Bango's internal standards, In addition, wire can be straightened via mechanical or heat treating processes. Typically, the measure of the straightness of a tungsten wire is obtained by cutting a ten inch long piece of wire and allowing it to lie on a flat clean surface. The maximum deviation from a straight line along its length is the quantitative measure of its straightness. In general, as the degree of straightness increases, tensile strength decreases. 4. Quality and Finish: Wire is free of scratches, kinks and distortions insofar as they are harmful to the intended end use of the product. Surface finish is supplied in the black, as drawn condition, where drawing lubricants and oxides are retained on the surface, or in the cleaned condition by firing in hydrogen or electrochemical etching. 5. Products Feature: 1. Excellent Conductivity 2. Resistance of high temperature. 3. Abrasion and Erosion. 4. Suitable for making heating wires. 5. Twisted wires for coating films under vacuum and for tungsten wires in electrical light sources usage.
Tungsten rod specifications: Grade: W-1 Purity: 99.95% Appearance: Shine with grey or dark grey metallic luster. Application: Mainly used to found ingredient of material, cutter and heads, tungsten wire for lights instruments and conductor of heat, crankshaft and cylinder barrel of advanced automobile, ingredient of kinds of heat-resistant steel, mainly used to guns, artillery, rockets, satellite, airplane and ship. Product Feature: High melting point, High-density, high temperature oxidation resistance, long service life, resistance to corrosion. Composition: Grade Tungsten content Contents of Impurity Elements Total Content Content of each element W1 99.95%min 0.05%max 0.01%max W2 99.92%min 0.08%max 0.01%max Dimension: Diameter(mm) Length(mm) 2-10 2500 10-30 2000 30-60 1500 60-100 1000 100-200 600 Technical process: Tungsten Powder Isostatic Pressing Bar Billet Sinering Semi-finished bar Forging Swaging Polished End products Inspection Packing
Quick Details Place of Origin: Henan, China (Mainland) Brand Name : Kekai Model Number: Mo1 Dimensions: As user's demand Shape: Wire Material: Molybdenum, Pure Mo Chemical Composition: Mo1 99.95%min. Condition: New Warranty:2 years Dimension: As user's demand Tensile Strength: 800N/mm2 Melting Point: 2610 Appearance: Metallic silver luster Recrystallization: Starting Temperature Packaging & Delivery Packaging Details: Molybdenum Wire: Wooden case or according to customer's request Delivery Detail: Within 7-20 days after order confirmation Product Description: Specifications: molybdenum wire 1. Grade: Mo1, Mo2, TZM, 2. Purity :> =99.95% 3. Characteristic: 1) Melting Point: 2610 Degrees Celsius 2) Density: 10.2g/cm3 3) High quality, workability 4. Certificate: GB/T9001:2008 / ISO9001:2008/ 5. Product Feature: High melting point, High-density, high temperature oxidation resistance, long service life, resistance to corrosion. 6. Dimensions and tolerance (According to clients requirements): Grade Mo-1 Grade Mo-1 The impurity content is not more than % Pb -- The impurity content is not more than % Si 0.003 Bi -- Ca 0.002 Sn -- Mg 0.002 Sb -- P 0.001 Cd -- C 0.020 Fe 0.006 O 0.003 Ni 0.003 N 0.003 Al 0.002 -- -- Application: Molybdenum wire, moly wire, spray wire is mainly used for auto parts spraying, such as piston ring, synchronizer rings, shift elements, etc. Molybdenum spray wire is also used in repairs of machine parts, such as bearing, bearing shells, shafts, etc. Furthermore, molybdenum spray wire is applied as an intermediate layer. With more than10 years experience in metal wire, we can supply the accustomed dimension such as dia.3.17mm, 2.31mm, 1.6mm and 1.45mm, etc. The reel weight of heavy molybdenum wire without welding can reach 25kg. Package: coils wrapped with waterproof paper with carton box outside. Specifications: Molybdenum Wire Types Diameter (inch) Tolerance (%) Molybdenum Wire for EDM 0.0024" ~ 0.01" �3% wt Molybdenum Spray Wire 1/16" ~ 1/8" �1% to 3% wt Molybdenum Wire 0.002" ~ 0.08" �3% wt Molybdenum Wire(clean) 0.006" ~ 0.04" �3% wt It is regular black with smearing graphite surface. After removing graphite, it has metallic luster Features: Very good interlaminar strength at strong thermal and mechanical loadings.
1. Specifications: Can process all kinds of sintering crucibles, machining crucibles and tubes according to the request of customers. Diameter(mm) Height(mm) Wall Thickness(mm) 6-10 �1.3 >150-270 �2.5 >200-300 �2.5 >10-15 �2.0 >270-380 �3.0 >300 �3.0 >15-20 �2.5 >380 �3.5 >300 �3.0 >20 �3.0 2. Surface Treatment: Annealed State, Electrolytic Polish 3. Application: Mainly used in metallurgical industry, machinery processing, glass and ceramic industries, as containers for coating materials. Because of molybdenum and molybdenum alloy material with high temperature, low pollution features, molybdenum crucible is widely used as LED industry ruby and sapphire crystal growth, rare earth smelting in the field of such as special high temperature resistant containers. 4. Advantage of our Mo crucible - uniform grain with densified microstructure ensures longer use time. - High special strength, high melting point - Excellent corrosive resistance, good thermal resistance. - Professional after-sales service
Molybdenum Heat Shield: As thermal insulation components, molybdenum heat shield and molybdenum covers play a important role for heat blocking and reflecting in sapphire growth furnace. A high purity, precisely sized, smoothly clean, easy assembly and appropriately designed heat shield is significant for crystal pulling quality. As the heat-shield parts in the sapphire growth furnace, the most decisive function of molybdenum reflection shield is to prevent and reflect the heat in the furnace. Heat-shield parts with high-density, exact-measurement, smooth-surface, convenient-assembly and reasonable-design has great significance in improving the crystal-pulling. Molybdenum heat shield Dimension (mm): Molybdenum Cover Plates Molybdenum Heat Shield/ Single sheet Sheet Thickness Dia (Max) Sheet Thickness Dia(Max) Height(Max) 2.0 0.1 660 0.2 2.0 0.1 450 2 660 1 1.0 0.08 660 0.2 1.0 0.08 610 2 660 1 0.5 0.04 660 0.2 0.5 0.04 700 2 660 1 0.3 0.03 660 0.2 0.3 0.03 700 2 660 1 Molybdenum heat shield processes and quality control: No. Processes Equipment Quality 1 Molybdenum sheet 1.Physical and chemical properties accordance with customers specification 2.Correct size 3.Clean surface, no defect. 2 Inspection 3 Roll bending Asymmetric three-rollers plate bending machine Correct barrel height and diameter 4 Drilling and riveting CNC milling machine, bench driller Firmly riveting 5 Cleaning Surface clean and no defect 6 Inspection Correctly positioned assembly holes 7 Assembling Clean surface 8 Cleaning Correct barrel height and diameter 9 Inspection Firm assembly, no bond between layers 10 Packing Firm wooden case within quality certificate
Specifications 1. Product name: Molybdenum electrodes 2.Material: Mo 3. high purity: 99.95% 4. Density: 10.2g/cc 5. Application: sapphire furnace, glass melting polished/ground moly electrode: Molybdenum electrode is electrodes made of material molybdenum, by applying its unique advantagestemperature resistance, continuous surface, stable edges good electrical conductivity, excellent corrosion-resistance -- to improve its entire quality and using age. Molybdenum electrode is silver gray metallic luster. It is isostatic pressed to forge to various types after sintering with medium frequency furnace and then turning, rolling, planning and milling. Meanwhile, the quality is unchanged, which can be seen from external and internal aspects, such as no lose side, no lose corner, and no crackle and divide layer. Thus, the surface of the molybdenum electrode is smooth and compact. Molybdenum electrode can be used for glass industry,andwork in the glass solution with the temperature of 1300�C. Molybdenum electrode is used as electro-heat equipment of the glass fiber kiln. It is an important part in rare earth industry. Its density is more than or equal to 10g/m3, and its purity can reach 99.5%. Molybdenum electrode: Dia.(mm) Tolerance Length(mm) Tolerance 16-20 +1.0 300-1500 +2 20-30 +1.5 250-1500 +2 30-45 +1.5 200-1500 +2 45-60 +2.0 250-1300 +3 60-100 +3.0 250-800 +3 It`s mainly used for metallurgy and machinery industry. Other sizes and special requests are available Mo has a unique property of which it's melting point can reach 2610 tungsten crucible is widely applied in high temperature vacuum furnace melting environment such as sapphire growing furnace, quartz glass melting furnace, and rare earth melting furnace. The working temperature of Mo sheet is above 1500. The melting process of the raw material for wool and fiber production is always by electrical heating with electrode, especially designed plate and Rod electrodes are generally used. We can provide stable quality Mo material with plate and Rod electrodes based on uniform density, purity and fine metal grain strength property. For glass melting application, high-purity, high-density, with other features of exact measurement and smooth surface has decisive influence on the success of quality control of glass melting and service life during meltng process. Composition: Grade The impurity content is not more than % Fe Ni Al Si Mg C N O Mo-1 0.01 0.005 0.002 0.01 0.005 0.01 0.003 0.008 Mo-2 0.01 0.005 0.005 0.01 0.005 0.01 0.003 0.02
Specifications: 1. Product name: Molybdenum tube 2. Material: Mo >99.95% 3. Density: 9.2~10.2g/cc 4. Grade: Mo1,Mo2,Mo3,TZM 5. Standard: ASTM B387 6. Surface Treatment: Annealed State, Electrolytic Polish 7. Characteristic: Certificate: ISO9001:2008 8. Product Feature: 1) High melting point, high strength, Melting Point: 2610 �C, Boiling Point:5560 �C 2) Outstanding thermal conductivity, 3) Excellent resistance to oxidation at high temperatures, 4) Excellent resistance to electrochemical corrosion 5) long service life, 9. Dimensions and tolerance(According to clients requirements): Density Outer Diameters Length Wall Thickness Forged Molybdenum Tube/Pipe �?�9.9g/cm3 4-150mm �?�800mm �?�1.0mm Sintered Molybdenum Tube/Pipe �?�9.7g/cm3 100-500mm �?�800mm �?�5.0mm 10. Composition: Grade The impurity content is not more than % Fe Ni Al Si Mg C N O Mo-1 0.01 0.005 0.002 0.01 0.005 0.01 0.003 0.008 Mo-2 0.01 0.005 0.005 0.01 0.005 0.01 0.003 0.02 11. Application: 1) Molybdenum Tube is widely used as the contact materials in silicon controlled rectifier diodes, transistors and thyristors. 2) Molybdenum Tube is used as mounting material for power semiconductor devices. 3) TFT - LCD monitor use of molybdenum target tube. And copper indium gallium selenide CIGS and cadmium telluride CdTe coating using two kinds of thin film solar cells of sputtering target rotating pipe. Vacuum furnace heating switches use 25.4 * 998 molybdenum tubes. And other specifications of the molybdenum tubes.
