Battery charger for all type of industrial battery 1. Thyristor base 2. Smps base Rane from 5 amp 24vdc to 2000 apm Iec
CTEK battery charger for car, commercial vehicles off road vehicle and motorcycle. Jump starter, Foxwel OBD scanner.
This battery charger is designed charge 12V battery from 48V DC Power Supply. High efficiency, Battery Charging unit. Wide input voltage range, with over-current and over-voltage protection function. Model No: DLS-4812BC Input Voltage: 48V DC Output Voltage: 13.8V DC Output Current (A): 1, 3, 5, 8, 10, 12 A
Product Brands: ABC, ABC Alkaline. Available Variants: AAA, AA, C, D, 9V Product of Indonesia
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Specifications: Pure sine wave inverter Built-in mppt solar charge controller and battery charger Selectable input voltage range for home use Selectable charging current based on applications Configurable ac/solar input priority via lcd setting Compatible to mains voltage or generator power Auto restart while ac is recovering Overload and short circuit protection Smart battery charger design for optimized battery performance Cold start function Parallel operation with up to 6 units only available for 4000kva and 5000kva model
Input: 110V/220V, 47-63HZ Specification: DC12V10Amp Constant Charging Voltage: 12V Constant Charging Current:10A Charging Mode : 3 Stages, CC, CV, Trickle Material: Aluminum alloy with Fan Dimension: 135*90*50mm Net Weight :0.7kg Application: Electric Vehicles & Tools Various Car Motorcycle Trucks Ships Lawn Mower RV ATV etc. Protection: Over-current, Over Voltage, Over Temperature, Short Circuit, and Reverse Polarity. Products can be Customized!
Input : 110V/220V, 47-63HZ Specification: DC12V6Amp Constant Charging Voltage: 14.6V (4s lifepo4 battery) Constant Charging Current:6A Charging Mode : 3 Stages, CC, CV, Trickle Material: Aluminum alloy with Fan Dimension : 135*90*50mm Net Weight :0.7kg Application : Electric Vehicles & Tools Various Protection: Over-current, Over Voltage, Over Temperature, Short Circuit, and Reverse Polarity. Products can be Customized!
Input : 110V/220V, 47-63HZ Specification: DC24V 4Amp Constant Charging Voltage : 29.4V (7s li-ion battery) Constant Charging Current:4A Charging Mode : 3 Stages, CC, CV, Trickle Material: Aluminum alloy with Fan Dimension : 135*90*50mm Net Weight :0.7kg Application : Electric Vehicles & Tools Various Protection: Over-current, Over Voltage, Over Temperature, Short Circuit, and Reverse Polarity. Products can be Customized!
Output: 84V 3A; Input:90 -230Vac, 50 ~ 60Hz Provide 1* Fuse and 1* US/UK/EU/AU standard power cable Aluminum Shell, LED Indicator light, Beautiful and Durable and cooling faster Overvoltage Protection, Over Current Protection, Short Circuit Protection, Reverse Protection
