DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Specification: Softening Point()ï¼? 80-90 90-100 100-110 110-120 Color(Gardner in 50% toluene),â?¤ 8-18 8-18 8-18 8-18 Ash(%),â?¤ 0.08 0.08 0.08 0.08 Acidity(mgKOH/mg),â?¤ 0.6 0.6 0.6 0.6 Recommended Application Adhesive Paint, Tyre Rubber Adhesive, Tire Rubber Adhesive, Tyre Rubber Application: 1. Used in Hot melt adhesive(HMA) and Solvent based adhesive(SBA) as tackifier resin 2. Solvent based paint 3. Printing Ink 4. Rubber Compounding 5. Asphalt emulsion mixtures Any inquiry, pls contact sofia.chu(at)zzdenglan.com freely.
PG100 resin is a kind of C5 modified C9 resin, with both character of C5 and C9 component, which is designed to tackify a variety of adhesive polymers, including ethylene vinyl acetate (EVA), styrenic block copolymers (SIS, SBS, SEBS), amorphous polyalphaolefins (APAO).
C5 Petroleum Resin with Grade SENO-PC5100 is a high class refined C5 Aliphatic Hydrocarbon Resins designed specially as a Binder to meet the technical requirements for hot melt road marking paint in Asian and American Markets.Our C5 petroleum resins offer good dispersion of fillers and pigments and also show excellent flow properties in Hot Melt Road Marking Paint Systems. Our C5 Hydrocarbon Resins are mainly recommended to the Thermoplastic Road Marking Paint and Hot Melt Road Marking Paint industry. Product Parameters Items SENO-PC5100 Appearance (eyeballing) yellowish granule Softening Point (R&B)�ºC 95-105 Color No. (50% Toluene)Ga. 5.0 Max Acid Value(mgKOH/g) 1.5 Max Ash Content(wt%) 0.10 Max Melt Viscosity(200�ºC)Cps 250 Max Application : SENO-PC5100 mainly use for Hot Melt Road Marking Paint,Thermoplastic Road Marking Paint and Pressure Sensitive Adhesives Packaging & Shipping :25kg/bag Store closed containers in a cool, dry, well-ventilated area. Avoid exposure to direct sunlight.
TC100 / copolymerized hydrocarbon resin is produced with and fraction, which has and strengths.It can replace the expensive C5 hydrocarbon resin in hot melt adhesive and rubber tire fields. In rubber tires, TC100 hydrocarbon resin not only can increase the adhesive force between colloidal particles, but also can enhance the adhesion between the particle and the cord thread.TC100 hydrocarbon resin is suitable for producing high quality rubber products. In adhesive, TC100 hydrocarbon resin have better initial adhesion and it also can adjust the adhesive durability and bonding strength. Product Specification: Item Test Method Unit Specification Range Softening Point ASTM-E28-58 95-105 Color ASTM-D-1544 GC 4Max Insoluble ETM-E-99 Vol% 0.05Max Acid Value ASTM-D-974 Vol% 0.2Max Specific Gravity ASTM-D-71-72A g/ 0.99-1.03 Features of TC100 C5/C9 Copolymerized Hydrocarbon Resin: Wide optional range.It will be more stabilized by the addition of antioxidant.Good compatibility with EVA,SIS and SBS etc. Applications:Hot melt adhesive,Synthetic rubber
Tc100/ copolymerized hydrocarbon resin is produced with and fraction, which has and strengths.It can replace the expensive c5 hydrocarbon resin in hot melt adhesive and rubber tire fields. In rubber tires, tc100 hydrocarbon resin not only can increase the adhesive force between colloidal particles, but also can enhance the adhesion between the particle and the cord thread.Tc100 hydrocarbon resin is suitable for producing high quality rubber products. In adhesive, tc100 hydrocarbon resin have better initial adhesion and it also can adjust the adhesive, s durability and bonding strength. Product specification: Itemtest methodunitspecification range Softening pointastm-e28-58 , 95-105 Colorastm-d-1544gc4max Insolubleetm-e-99vol%0.05max Acid valueastm-d-974vol%0.2max Specific gravityastm-d-71-72ag/0.99-1.03 Features of tc100 c5/c9 copolymerized hydrocarbon resin: Wide optional range.It will be more stabilized by the addition of antioxidant.Good compatibility with eva, sis and sbs etc. Applications:hot melt adhesive, synthetic rubber Package: 25kg kraft paper bag Storage: All resins with low softening point present a risk of solidifying or lump. For softening point less or equal to 110, , we suggest you keep resin in a cool (25, max) ventilated place and avoid direct sunshine.