A full range of board to board connectors in 0.5mm, 0.8mm, 1.0mm, 1.27mm, 2mm, 1.27mm x 2.54mm, 2.54mm, 3.96mm and 5.08mm pitches.
High quality electronic connector
Chinese manufacturer(brand kefa) of screw terminal blocks, spring terminal blocks, pluggable terminal blocks, barrier terminal blocks, feed through terminal blocks, transformer terminal blocks, ws din rail terminal blocks, etc. Cnkefa, ISO9001:2000, ISO14001, CE, UL, TUV, ROHS.
Bnc connector Bnc connector is one of our typical products. Please contact us and talk abour packing, moq and so on
Housing Electrical
Electrical board hinged IP31. Designed for assembly of electrical boards using modular equipment. Electrical board built-in IP31. Designed for assembly of electrical boards using modular equipment.
VIBRATION CONNECTORS MANUFACTURERS & SUPPLIERS Stainless steel vibration eliminator: Aeroflex Vibration eliminators are specially designed to absorb mechanical vibration and destructive force of noise which is transmitted by the compressor, and also eliminate the stresses linked with piping thermal expansion in refrigeration and air condition installation. These connectors are TIG welded stainless steel hose with copper pipe, due to there is not any brazing so these connector bear more temperature as compared to brazed fitting The main function of vibration eliminator is to absorb compressor vibration and stop its transition into pipe network, by isolating the vibration the risk of damage to pipe work and related component reduce, 1.1 Size range of vibration eliminator: The comprehensive range of vibration eliminator are available from to 3 1/8 Outer diameter of copper tube, copper tube are comply a per ASTM B88 & ASTM B88M (water & general plumbing system) & ASTM B280 (air conditioners & refrigeration system) 1.2 Material specification: Aeroflex Vibration eliminators are manufacture from EN 10028-7, Stainless steel SS 321 & SS 316L annular corrugated hose with SS 304 stainless steel braid. All unit are brazed with copper tube, detail dimension of pipe and vibration connector are in the table. All the units are ultrasonically cleaned and completely dried made suitable to refrigeration system Individual package of connector are remain under sealed plastic tubing. The maximum test pressure is 1.5 time of maximum operating pressure and minimum burst pressure is 5 time of maximum operating pressure. Copper tube end are designed as sweat connection for refrigeration tubing which have inner surface as per ASME B16.18 1.3 Installation conditions: Aeroflex vibration eliminator should be installed as close as possible to the compressor and end away from the source of vibration. Vibration eliminator should be installed perpendicular to the direction of vibration (in-line with the compressor crank shaft) Horizontal Vibration: Where source of vibration is only in the horizontal plane, a single vibration and noise eliminator may be installed. Best results will be achieved by installation at 90�° to the source which is normally the crank of the compressor in a horizontal plane. See fig. 1 Vertical / horizontal vibration: Where the source of vibration and noise is in both horizontal are in vertical planes. Best result will be achieved by installing two vibration eliminators at right angle to each other see fig. 2 Although the copper tube end of vibration absorber are attached by TIG welding (special alloy filler) during installing if unit is over heated there is not effect on the connector
Field installation connector also be called Fast install connector is a new kind of connector that could be used in FTTH project scene. They donot need to polishing, no epoxy. They could be installed in the field and make connection less than two minutes. Of course, It donot need fused the fiber. Just some little tools enough, so it could save time and cost. Connector Type : SC Polishing : UPC and APC Ferrule : Ceramic V-Groove : Plastic Material Cable Diameters : 2x3mm FTTH Drop Cable;1.6x2.0mm FTTH Drop Cable Length : 51mm Insertion Loss : 0.3dB(typical);0.5dB(Max) Return Loss : UPC 40dB;APC 50dB Tension Strength : 30N Operating Temp : -40 C~+75 C
Fast installation connector also be called Field install connector is a new kind of connector that could be used in FTTH project scene. They don't need to polishing, no epoxy. They could be installed in the field and make connections less than two minutes. Of course, It donot need fused the fiber. Just some little tools are enough, so it could save time and cost. Part No. : J-P-SSA-50 Connector : SC APC Ferrule : Ceramic V-groove : Plastic material Cable Diameters : 2.0/3.0mm Simplex cable;2x3 FTTH Drop Cable Dimension : 50mm Insertion Loss : 0.3dB(typical); 0.5dB(Max) Return Loss : UPC 40dB;APC 50dB Tension Strength : 50N Operating Temperature : -40 C~+75 C
Material: Zinc Alloy, Size: 3/8",1/2", 3/4",1",1-1/2", 2", 3",4". Fit for liquid tight flexible conduit.
