Optfocus International Co., Ltd.

Technical Specifications
Operating standards: IEEE802.3z/AB, 10/100/1000Base-T and 1000Base-SX/LX/HX
MAC address table: 4K
Data Buffer: 256K
Connector: UTP: RJ-45,10/100/1000Mbps; Fiber: LC,1000Mbps

Cable :
UTP cable: Cat 5e or Cat 6 (the max distance up to 100m)
Fiber : multimode : 50/125, 62.5/125¦Ìm (the max distance up to 550/224m)
singlemode : 8.3/125, 8.7/125, 9/125¦Ìm (the max distance up to 100km)
Flow control
Full Duplex: IEEE802.3x
Half Duplex: back pressure.
Power: AC 220V(170-260V) 50Hz; DC 5V£¬1A
Ambient temperature: 0 ¡« +50
Storage temperature: -20 ¡« +70
Humidity: 5% ¡« 90%

Dimensions:
Internal Power: 40 (high) x 110 (width) x 140 (length) mm
External Power: 26 (high) x 70 (width) x 93 (length) mm.

Technical Specifications
Operating standards: IEEE802.3z/AB, 1000Base-T and 1000Base-SX/LX
MAC address table: 4K
Data Buffer: 256K
Connector: UTP: RJ-45,10/100/1000Mbps; Fiber: SC,1000Mbps

Cable :
UTP cable: Cat 5e or Cat 6 (the max distance up to 100m)
Fiber : multimode : 50/125, 62.5/125¦Ìm (the max distance up to 550/224m)
singlemode : 8.3/125, 8.7/125, 9/125¦Ìm (the max distance up to 100km)

Flow control
Full Duplex: IEEE802.3x
Half Duplex: back pressure.
Power: AC 220V(170-260V) 50Hz; DC 5V2A
Ambient temperature: 0 ¡« +50
Storage temperature: -20 ¡« +70
Humidity: 5% ¡« 90%
Dimensions: 40 (high) x 110 (width) x 140 (length) mm .

OFS Gigabit Single Fiber Converter can convert Optical£­Electric Ethernet signals between 10/100/1000M UTP interface (TX) and 1000M optical fiber interface (FX). The traditional 10/100/1000M gigabit Ethernet can be extended to the distance of 90km through single optical fiber link. The performance and quality of the products are excellent because of adopting latest Gigabyte IC from USA and Taiwan. It must be used in couples because the transmitted optical differs from the receive optical in wavelength. 6 Group LED indicated lights could fully monitor the working conditions of converters. It is easy for users to observe and diagnose the failure of converters.

Main features
The transmission of a channel signals can be completed by single fiber. It has doubled in quantity of fiber data transmission compared with twin fiber.
Auto negotiation function allows UTP port to auto select 10/100/1000M and Full Duplex or Half Duplex
The UTP port supports MDI / MDI-X auto crossover.
Supporting the max 1536 bytes packets
Adopting internal power supply to insure equipment at long-hours work stably.

Technical Specifications
Operating standards: IEEE802.3z/AB, 1000Base-T and 1000Base-SX/LX
MAC address table: 4K
Data Buffer: 256K
Connector: UTP: RJ-45,10/100/1000Mbps Fiber: SC,1000Mbps.

Cable :
UTP: Cat.5e or Cat.6 (the max distance up to 100m)
Fiber (singlemode): 8.3/125, 8.7/125, 9/125, 10/125µm (the max distance up to 90km)

Flow control:
Full Duplex: IEEE802.3x
Half Duplex: back pressure
Power: AC. 220V(170-260V) 50Hz; DC. 5V 2A
Ambient temperature:0 ¡« +50
Storage temperature:-20 ¡« +70
Humidity:5% ¡« 90%
Dimensions:40 (high) x 110(width) x 140 (length) mm.

14 Slots Media Converters Rack
It is acceptable for the most 14 sets of 10M, 10/100M 10/1001000MMedia Converters within a rack-mountable chassis which is supplied with unified power. Installing at the center of network, the Rack not only reduce the links, simplify the structure, but also ease for management and maintenance.

Main features:
The power of the Rack can be supplied by the type of single power or dual power. Adopting dual power supply, the load of each power can be reduced and the life of the power would extend. When one power supply is at fault, the other one can still work independently. It would enhance the reliability of the RACK.
Supplying the Converters or Powers to be plugged and played.
It is possessed of stable performance, large capacity of power supply, and ease for management and maintenance
2U high: 19-inch standard design

Technical Specifications:
Capacity : 14 slots available
Power: Input: AC 100 ¡« 260V, 50¡«60HZ
Output: DC +5V 12A
Power protection: protection from over voltage, over current and short circuit
Working temperature: 0¡«50
Storage temperature: -20¡«70
Relative Humidity: 5%¡«95%
Dimensions: 485 (wide), 245 (length), 90 (high) mm.

Operating standards: IEEE802.3u, 10/100Base-TX and 100Base-FX
MAC addresses table: 1K
Data buffer: Built-in 128Kbyte RAM .
Connectors: UTP Connector: RJ-45, 10/100Mbps; Fiber Connector: ST/SC/FC, 100Mbps

Cable:
UTP: Cat. 5 (the max distance up to 100m)
Fiber ( Multimode): 50/125, 62.5/125m, the max distance up to 2km or 5km
Fiber ( Singlemode): 8.3/125, 8.7/125, 9/125, 10/125m, the max distance up to 20 -120km
Flow Control
Full Duplex: Supporting standard IEEE802.3x
Half Duplex: back pressure
LED: Power, FX SD, FX Link/Act, TX 100, TX FDX, TX Link/Act.
Power Requirement: AC 170 ¡« 240V, DC 5V.
Ambient Temperature: 0 ¡« 70
Humidity: 5 ¡« 90%
Dimensions: Internal power: 30, 110, 140mm
External power: 26, 70, 93mm.

Wavetel Hybrid IPPBX HG100 is a Multi-function Integrated Service Switch System with All-in-one solution. It applies TDM, VoIP, advanced and soft-switch technology, and it could also be used as trunk gateway or signaling gateway. HG100 provides multiple types of interfaces including Ethernet, FXS, FXO and E1, so that it could work with IAD, PBX, analog phone, IP phone, soft phone, Fax, POS, etc. HG100 can be interconnected with third-party gateway, soft-switch or IMS through SIP and other agreements. At the same time, it can also be interconnected with PSTN or traditional PBX through SS7, PRI, etc.

Voip Gateway IAD series to meet the NGN requirement of Telecom carrier, Internet Service Provider, SMB/SME users and home users.It is able to provide safe and high-efficiency voice services, with all kinds of protocols and functions.

Wavetel Hybrid IPPBX HG100 is a Multi-function Integrated Service Switch System with All-in-one solution. It applies TDM, VoIP, advanced and soft-switch technology, and it could also be used as trunk gateway or signaling gateway. HG100 provides multiple types of interfaces including Ethernet, FXS, FXO and E1, so that it could work with IAD, PBX, analog phone, IP phone, soft phone, Fax, POS, etc. HG100 can be interconnected with third-party gateway, soft-switch or IMS through SIP and other agreements. At the same time, it can also be interconnected with PSTN or traditional PBX through SS7, PRI, etc.

Enquire us today