BW Chemicals is (www.bwchemicals.com.pk) a manufacturer of different wax emulsions, based in mid country Pakistan. We manufacture different types of wax emulsions based on Paraffin, Polyethylene and Microcrystalline. The emulsion have different ionic moieties based on customer request. Having a large production capacity we are pleased to serve different industries with top of the line solutions for there wax emulsion needs. We mainly serve Textile, Paper & Board, Leather and Construction Industries.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
We supply balustrade and its related components like connectors, saddles, pipes end caps in SS201, SS304, SS316, SS316L. Pipes OD42.2mm*2mm. Also available other OD on request. Balustrade shape round, square any other custom designed shape. Height about 1060mm. Finish: satin, Glossy.
Product Description: We supply connector in SS201, SS304, SS316, SS316L suitable for pipes OD42.2mm*2mm. Also available other OD on requist. Connectors in round, square any other custom designed shape. Finish: satin, Glossy.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Indian Granite: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing. 1. Indian Granite-Black 2. Indian Granite-Black Galaxy 3. Indian Granite-Black Pear 4. Indian Granite-Coffee Brown 5. Indian Granite-Coral Gold 6. Indian Granite-Jasemine White 7. Indian Granite-River White 8. Indian Granite-Sappahire Blue 9. Indian Granite-Silver Waves 10. Indian Granite-Steel Grey 11. Indian Granite-Tan Brown 12. Indian Viscon White 13. Indian Granit-Aspen White
Indian Granites: Indian Granite: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing. 1. Indian Granite-Black 2. Indian Granite-Black Galaxy 3. Indian Granite-Black Pear 4. Indian Granite-Coffee Brown 5. Indian Granite-Coral Gold 6. Indian Granite-Jasemine White 7. Indian Granite-River White 8. Indian Granite-Sappahire Blue 9. Indian Granite-Silver Waves 10. Indian Granite-Steel Grey 11. Indian Granite-Tan Brown 12. Indian Viscon White 13. Indian Granit-Aspen White
Indian Granite Black: We can supply Premium Grade to commercial grade. Size and surface and sides finishes can be customized. Finishes: Mirror, Matte, Flame finish etc. Slabs: Length- 6’ to 9’, width: 2’ to 3’, thickness:18mm (+/-1) Tiles: 45x45cm, 60x45,x60x60cm in 10mm. Any other sizes can be customize. Edge finish as per your requirement. Surface finish: we have automated polishing and Semi Automated polishing.