Snake Spring Coupling Housing is suitable for coaxial axis drive shaft system, with certain compensation performance of angular, radial and axial offset between two shafts, operating ambient temperature -30 ~ 150C, transmission torque 45-800000N m. The Basic Parameters And Main Dimensions Of The Snake - Shaped Yellow Coupling  mm Model Nominal Torque  Tn N m Allowable speed  [n] r/min Shaft hole  diameter  d mm Shaft hole  length L mm Overall length  Lo mm L, mm D mm Clearance  C mm inertia  moment I kg. m2 Weight kg JSA1 45 18 28 47 97 66 95 0. 0014 1.91 JSA2 140 4500 22 35 68 105 0. 0022 2. 59 JSA3 224 25 42 50 103 70 115 0. 0033 3. 36 JSA4 400 32 50 60 123 80 130 3 0. 0073 5. 45 JSA5 630 4350 40 56 63 129 92 150 0.0119 7. 26 JSA6 900 4125 48 ã??65 76 155 95 160 0. 0185 10. 44 JSA7 1800 55 80 89 181 116 190 0. 0451 17. 70 JSA8 3150 OvvU 65 95 98 199 122 210 0. 0787 25. 42 JSA9 5600 2000 75 110 120 245 155 250 0. 1780 42. 22 JSA10 8000 2250 80 120 127 259 162 270 0. 2700 54. 45 JSA11 12500 2025 90 140 149 304 192 310 0.5140 81.27 JSA12 18000 1800 110 170 162 330 195 346 0. 9890 121.00 JSA13 25000 1650 120 200 184 374 201 384 1. 8500 178. 00 JSA14 35500 1500 140 200 184 374 271 450 3. 4900 234 JSA15 50000 1350 160 240 198 402 279 500 6 5. 8200 317 JSA16 63000 1225 180 280 216 438 304 566 10. 4000 448
1) plastic injection molded parts 2) mould design and development 3) automotive plastic parts 4) auto electrical parts 5) industrial/automotive battery parts 6) plastic household products 7) gear moulding 8) over moulding 9) insert moulding.
Semiconductor machined parts, heavy duty equipment parts, metal casting parts, steel casting parts, investment casting, machined parts, valve casting products, automation parts..
Commodity: Synthetic Cryolite Formula: Na3AlF6 M.W.: 209.95 Properties: The product is a white crystalline powder or a sandy-size granularity, and a pinkish crystalline powder or a sandy-size granularity as well. Sp.gr.2.953.01g/cm3, melting point about 1000centigrade, specific heat 1.056j/gcentigradeat 18100centigrade. Its slightly soluble in water, but insoluble in anhydrous hydrogen fluoride. The content of its crystal water will be decreased while the increasing of the molecular ratio, therefore its loss on ignition will be also decreased while the increasing of the molecular ratio. After the paste of synthetic cryolite with different molecular ratio dehydrates, the loss on ignition at 800centigrade will appear 10.34%, 6.22% and 2.56% when the molecular ratio reaches 1.74, 2.14 and 2.63 reactively. Specifications: Appearance white powder F 52% min Al 12% min Na 33% max SiO2 0.36% max Fe2O3 0.08% max CaO 0.5% max P2O5 0.03% max SO4 0.6% max H2O 0.4% max Loss on ignition 2 % max Uses: Its mainly used as a flux in the aluminum smelting by fused-salt electrolysis; also an opalizer in the manufacture of enamel; an opacifier and auxiliary solvent of glass and enamel; an insecticide of crops; a flux in aluminum alloy casting; and in the production of ferrous alloy and effervescing steel; as well as a wear-resistant filler for resin and rubber-boned abrasive wheels. Packing & Storage: In plastic coating woven bags with plastic film inside, 25kg,40kgs, 50kgs or 1000kgs net each, or as the requirement of clients.Stored: in a cool , ventilated, dry place.
Material: BAMBOO, natural bamboo, aluminum, and high quality PP plastic Product Type: Bamboo Comestic Technique: Carved Regional Feature: Viet Nam Theme: Flower Place of Origin: Vietnam Brand Name: 99 Gold Data Model Number: Product Name: Bamboo Lipstick Tube Color: Natural Bamboo Color Usage: Comestic Packaging Lipstick Logo: Engrave OEM Logo MOQ: 1000 Pieces Shipping Times: 7 Days Sample time: 5-7 Working Days Feature: strong, non-toxic, no odor, reusable, safe and also eco-friendly Material of face: Surface Handling Screen Printing
CLZ type gear coupling is suitable for connecting two horizontal coaxial drive shafting. It has a certain ability to compensate the relative offset of two shafts, and transmits nominal torque 0. 71 -- 1000KN
Shoes, air filter cartridges, oil filter, water filter cartridge, dust collection filter cartridges, dust collection filter bag, liquid filter bag, carbon cartridge ,gas filter, empty glass bottle, empty wine bottle, glass jar, glass bowl, flavoured dry fruit, all type of rice, makhana , leather product, ladies kurti, plazo sets , t shirt, curtain, cotton apron, cushion cover , kitchen towel, garlic powder, ginger powder, onion powder, fresh onion, garlic, ginger, potato, bio fertilizer , door handle , door lock, furniture and sandstone tile, spices, vegetable, coffee powder, frozen pea, frozen sweet corn, frozen mix vegetable, wooden furniture, moringa powder, neem powder, dry fruits, fruits, ready to eat, garments, artificial jewellery, handicraft, shower, ultra slim shower, ro booster pump, adjustable mobile stand, lady bag and wallet, men bag and wallet, portfolio, machine casting, ro booster, sandwich shower, ultra slim shower head, donkey milk and donkey milk powder.
We are manufacturer of auto components in forging, casting and pressing commodity. 1.we have manufacture forging items like forge ring, nut , bolt, fork, lab ring, casting valves /cover / pressing parts line cover/ filters , connecting rod . 2.precision turned components with cnc/ troub machine/vmc 3. machining of forging and ci casting parts /aluminum castings 4. components presently manufactured have application in auto sector, home appliances and electrical industry..
Ramming mass is commonly used in metallurgy, building materials, non-ferrous metal smelting, chemical, machinery and other manufacturing industries. Ramming mass is widely used in non-core intermediate frequency furnace and core induction furnace. As an intermediate frequency furnace ramming material, refractory ramming is applied to melt gray cast iron, nodular cast iron, malleable cast iron, vermicular cast iron, and cast alloy steel; to melt carbon steel, alloy steel, high manganese steel, tool steel, heat resistant steel, stainless steel, molten aluminum and its alloys; to melt red copper, brass, white brass, bronze and its alloys, etc. Induction furnaces are used for melting cast iron, mild steel and various alloy steels in foundries and making of steel in mini steel plants using sponge iron The refined high silicon, low iron quartz sand and quartz powder are selected and the fused quartz sand is added as the refractory material., with no slag, no crack, damp proof, convenience of repair, and the corrosion resistance, thus greatly improving the furnace service life span and the economic benefit.. Silica ramming mass can safely be used up to an operating temperature of 1600 deg C. Since it expands very little, it is superior to both alumina and magnesia refractories to resist thermal shocks Acid ramming material is the premixed ramming mass of the lining material. The acid ramming mass is used to smelt a series of metal materials such as ordinary steel and carbon steel. The lining practice best suited to a particular furnace depends upon the capacity and design of the furnace, operation practice adopted during making of a heat, and furnace output.
Door hardware, hinges, die casting products, zamak die casting, aluminum die casting, door handles, ironmongery, clamps, pipes, knobs, broom clamps, brackets, locks, pad bolts, auto parts, lugs.
We supply a wide range of Aluminum Ingots that meet international standards and specifications. Aluminum ingots are a crucial raw material used in numerous industries, including automotive, construction, aerospace, and electrical. They are highly sought after for their lightweight, corrosion-resistant, and excellent conductivity properties. Aluminum ingots serve as the building blocks for manufacturing various Aluminum-based products, such as sheets, rods, extrusions, and castings. Specifications/Special Features : Aluminum A7/A8 GOST 11069-74 Quality Value demanded by norm GOST 11069-74 A7 A8 Al Min. 99,7% Min. 99,8% Fe Max. 0,16% Max. 0,11% Si Max. 0,15% Max. 0,08% Cu Max. O,01% Max. 0,01% Zn max. 0,05% Max. 0,05% Ti max. 0,02% Max. 0,02%. Contact AWF Global Trading Company Limited today to discuss your requirements. Our team will be delighted to assist you and provide you with the best solutions tailored to your needs. Let us be your partner in the world of commodity trading.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Gremlog Trading DMCC stands at the forefront of the metal recycling industry, offering a meticulously curated selection of carefully sourced and recycled metal scrap solutions. Our comprehensive range includes: Cast Iron Scrap: Our cast iron scrap, derived from the recycling process, is subjected to thorough quality checks, ensuring its suitability for applications requiring robust and high-performance cast iron. Aluminium Scrap: Crafted from precise recycling processes, our aluminium scrap adheres to stringent purity standards, ensuring optimal performance in the production of high-quality aluminum alloys. Steel Scrap: Derived from the efficient recycling process our steel scrap undergoes rigorous processing to meet exacting specifications, guaranteeing consistency and reliability for diverse industrial applications. Rebars: Our meticulously sorted and processed rebars are characterized by its uniformity and purity, ideal for applications demanding precise metallurgical properties. Fine Iron Scrap: Engineered for excellence, our fine FE scrap undergoes advanced processing, delivering a product that meets the stringent demands of modern manufacturing processes.
Casting and refractory materials. our products are ferro alloys, carbon products, pure ingot metals, refractories materials, and noble alloys base metals..
We customize various aluminum die casting parts for metering, electrical, lighting, and auto field.
Name: aluminum die casting, zinc die casting products Material: aluminum, zinc Can be customized
Raw melting material - aluminum scraps, cans, engine waste etc. Output capacity - 5-30 tons/h, customized Automation - Full automatic/ half automatic (based on output requirement and investment budget Ingot type - ADC12 (7.5kg/ 10kg / customized) 1. After cleaning the oil and grease of waste aluminum, manually put it into the furnace with a forklift; 2. Ignition for melting furnace .Heat up to 680C, and input appropriate proportion of alloy elements. Heat up to 800C, melt and stir evenly, then fetch samples to the spectrometer for testing. Every lot of production need to do testing . 3. Put A tool that attracts iron into the furnace by forklift, to suck away the iron in the aluminum water. 4. Put the slag agent into Alu liquid to remove the slag. After slag removed , put the slags into Aluminum ash separation machine , and let the aluminum water and ash separate. The proportion of slag agent and aluminum liquid is 1:500 5.Open the drain valve and the aluminum water flows automatically to the ingot production line After the ingot casting is completed, the ingot stacking robot will stack the ingots, which means the production is completed.