Fiberglass mesh is designed to reinforce concrete structures instead of conventional metal reinforcement.
It has the following advantages in relation to metal:
9 times lighter
3 times stronger
corrosion resistant
significantly accelerates the reinforcement process (knitting on the object is not necessary)
no need to put chairs
low thermal conductivity
Composite bars are connected to the network using a unique patented technology, which uses high performance automatic equipment. The joint is also a stool that forms a protective layer of concrete. For different rod diameters, the height of the stool is different.
The only restriction on the use of fiberglass mesh is the inability to operate at temperatures above 150 �° C, therefore, it is not recommended to reinforce structures that must meet special fire requirements: building floors of more than 3 floors, bridge columns, monolithic towers of more than 3 floors.
With this exception, almost the entire range of concrete structures remains:
Fiberglass mesh is based C/E-glass yarn as raw material, then coated by alkaline resistant latex.
Featured by high strength and low weight, alkali resistant, good insulation properties and dimensional stability, etc. It is widely used for wall reinforced material, internal wall plaster work, EIFS system, wall defects repair work and so on.
Construction Fiber Glass Mesh Net/ Stone Reinforcement Fiberglass Mesh
Construction Fiber Glass Mesh Net/ Stone Reinforcement Fiberglass Mesh
Feature
High strength and low weight, high tensility.
Alkali resistant, acid resistant, waterproof.
Good insulation properties, good dimensional stability.
Good impact resistance and not easy to be teared.
Thermal preservation, fireproof, soundproof.
Durable and long service life.
Specification
Material: C/E glass fiberglass yarn, modified acrylate copolymer glue.
Mesh size: 4 4, 5 5, 7 7, 8 8, up to 12 12 mm.
Plastic coated layer: 20 g/m2.
ZrO2
Normal: (14.5±0.8)%.
GRC reinforced fiberglass mesh: 16.5%.
TiO2: (6±0.5)%.
Strength retention rate: 90%.
Width
Plaster fiberglass mesh: 0.9, 1, 1.1, 1.2, 1.75 m.
Fiberglass mesh: 5, 10, 15, 20 cm.
GRC reinforced fiberglass mesh: 0.6 m, 0.9 m, 1.0 m.
Roll length: 20-500 m.
Weight
Normal: 30, 45, 75, 145, up to 500 g/m2.
For EIFS: â?¥ 160 g/m2.
Color: white (normal), orange, blue, green, any colors available.
Package: First plastic film, then carton box or according to your requirement.
Construction Fiber Glass Mesh Net/ Stone Reinforcement Fiberglass Mesh
Category
Construction Fiber Glass Mesh Net/ Stone Reinforcement Fiberglass Mesh
In addition to the above points, fiberglass mesh is also used elsewhere. For example: roof waterproofing.
* Reinforce cement.
* Reinforce plastic.
* Reinforce bitumen.
* Reinforce marble.
* Reinforce mosaic.
* grinding wheel base fabric. and other building materials.
Fiberglass mesh is made of quality filamentary plastic coating glass fiber yarn by special weaving technique. Fiberglass mesh has plain and neat appearance, good season-fitting, steady and soft color. Fiberglass mesh is the first choice for home, hotel and offices to prevent sunshine.
black fiberglass tissue can offer widest range of woven fabrics which are made of E-glass yarn. Our woven glass fabrics are manufacture with state of the art weaving technology and the best control over thickness, weight and strength.We can offers the materials engineer a wide choice of control fabric properties to satisfy design needs and objectives. Our extensive range of Fibreglass fabrics are globally recognised for its quality.
black fiberglass tissue with fire retardant and alkali-free performance, is suitable as a surface lamination for fiberglass wool and rock wool thermal insulation.
418603 Fiberglass Mesh For Construction Suppliers
Short on time? Let Fiberglass Mesh For Construction sellers contact you.
Features
1. High tensile strength
2. Alkali resistant
3. Good cohesion
4. Can firmly combine with eps board
Application
1. Fiberglass mesh is used for wall reinforcement.
2. Fiberglass mesh is ideal material for out-side wall heat insulation.
3. Fiberglass mesh can be applied to bitumen as roof waterproof material, so as to strengthen the tensile strength and life time of bitumen.
4. For reinforcement of marble, mosaic and stone, plaster.
Specifications roll size
Aperture size weight/ square meter width length
3mm x 3mm
4mm x 4mm
5mm x 5mm
6mm x 6mm 70g-200g/m2 0.2m-4m 30m-300m
7mm x 7mm
8mm x 8mm
9mm x 9mm.
Packing1: shrink plastic film then woven bag. Package2:plastic film, then in carton box.
Aggregates are mixtures of sand, gravel, crushed rock or other bulk minerals used in construction, principally as a component of concrete, and in civil engineering. At CEMENTATION we supply aggregates for a range of core applications, from fill materials to aggregates that can be used in concrete, precast concrete, asphalt and for surface dressing. Aggregate plays an important role in concrete and construction part. We supply quality material which makes durable concrete with higher compressive strength and low permeability having better finish. We can supply a wide range of coarse, fine and blended aggregates in accordance with international standards.
We acquire rock mines and stone crushing plants and enable us to fulfil contract of any size. Progressive stages if crushing and screening enable us to produce a range of aggregate sizes (06mm to 65mm)
APPLICATIONS
Road and Highway surfaces
Constructions or Civil work
Railway Ballast
To make Concrete or Asphalt
Filling
Sodium Silicate is an inorganic chemical wherein its formulations vary depending on amount of Na2O and SiO2. This compound is well known as Water Glass in industries.
We mainly supply following types of Sodium Silicate:
The basalt fiber roving of our company adopts the new tank kiln method and 2400 hole large leakage plate to form basalt roving products With a series of advantages such as high strength, large modulus, good temperature resistance, good chemical corrosion resistance and good electrical insulation, basalt is produced with homogenized basalt raw materials, with excellent performance, stable quality and small dispersion coefficient.
Basalt fiber roving is a new material to replace glass fiber and carbon fiber
The CORI is the product for the direct reduction unit:
First, it will be stored in product passivation silos, its transportation by conveyors. After that, it will be stored in the warehouse for further use.
Production rate fo312 T/H. Assuming 8,000 hours of annual
operation, this equates to in annual production of 2,500,000 tonnes.
-IRON: (Rod a Benton):Hot-rolled product in multipurpose steel for high-adherence construction, weldable in RB 500 grade. NA 8634(2015) and ISO 6935-2 (2015). Diameter:
A wide range of diameters: 8,10,12, 14, 16,20,25,32,40 mm.
Length :12m (-0mm +100mm) with the possibility of making specific lengths of less than 12m according to customer demand for diameters ranging from 8mm to 16mm.
12m to 18m for diameters ranging from 16mm to 40mm.
Marking :
A specific AQS marking is engraved on the rebar bars for the diameters: 8,10,12,14,16mm And the identifying code AQS-diameter-RB500 for the diameters: 16,20,25,32,40mm
- Portland Cement 42.5 (Bags, Bulk)
-Wire rod: of round section with a diameter varying between 5.5 mm to 14 mm, of high quality.
The round and smooth wire rod is obtained by hot rolling in accordance with the Algerian standard an 8634 and according to international standards.-The Fields Of Use Of Wire Rod Are As Follows:- Drawn Wire-Welded Mesh-Nail, Tie Wire, Galvanized Wire- Gabions- Barbed Wire-Spring Wire- Bolt-Nut-Screw- Paperclips-Pickup Wire-Welding Wire
-BILLET: A billet is a section of metal used to roll into bars and shapes. It can be produced with ingots or directly by continuous casting. Billets are used as raw materials or for extrusion, forging, rolling and other metal processing operations.
Fiberglass Reinforced Plastic grating is made by interlacing glass fibers and molded by
resin casting. With its many rectangular and square spaces, it provides two-dimensional
homogeneous mechanical characteristics.
The typical size of the product is - 1220 x 3660 mm. However, it is available in different mesh
sizes and thickness
- Advantages
- Easy to assemble
- High Load-bearing capacity
- Easy to install and maintain / repair
- Durable in harshest environments
- Suitable for ventilation and natural lighting
* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.
When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.
PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.
* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.
* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.
* The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites.
Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature.
Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts.
PREPARATION OF FURANE MORTAR :
Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life.
Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
1. Thickness: The thickness of the steel plate mesh ranges from 0.5mm to 8mm.
2. Mesh width: The mesh width ranges from 2.5mm to 50mm.
3. Mesh length: Mesh length ranges from 4.5mm to 100mm.
4. Stem thickness: Stem thickness ranges from 0.5mm to 8mm.
5. Network width and length: the network width range is 0.5m to 2m, and the network length range is 1m to 4m.
6. Other specifications: Long pitch TB is 12.5-200mm, short pitch TL is 5-80mm, the mesh size is 600-4000mm long * 600-2000mm wide.
Its wide range of uses, including machine filter, medicine, paper, filtration, aquaculture, battery nets, packaging nets, mechanical facilities protection, arts and crafts manufacturing, high-grade speaker net cover, decoration, child seats, baskets, baskets and road protection. In addition, the steel plate net is also used for working machinery and boilers, platforms, escalators, walkways, such as tanker foot nets, heavy oil mines, locomotives, 10,000-ton ships, etc.
The Ground Granulated Blast Furnace Slag (GGBS/GGBFS) is a type of eco-friendly green building material and high quality secondary cementitious material for concrete and cement. It is recognized as one of the best secondary cementations material for building high durable concrete stricture in the world today! GGBS has taken over a top place of high-performance cement and concrete mineral additives with its unique characteristics of hydration, low-price raw material. GGBS is obtained by quenching molten iron blast furnace slag (a by-product of iron and steel making) in water or steam. It is then further grounded into the desired fineness in terms of the required particle size distribution. The main components of blast furnace slag are CaO (30-50%), SiO2 (28-38%), Al2O3 (8-24%), and MgO (1-18%). The other important aspect of GGBS is its superiority in concrete durability which extends the lifespan of buildings from fifty years to a hundred years.
APPLICATIONS
Soil stabilization
Mortar
Used in combination with Portland cement
Pre-cast concrete
Ready mix concrete
Specialist projects
Feldspar is the name given to a group of minerals distinguished by the presence of alumina and silica (SiO2) in their chemistry. This group includes aluminum silicates of soda, potassium, or lime. It is the single most abundant mineral group on Earth. They account for an estimated 60% of exposed rocks, as well as soils, clays, and other unconsolidated sediments, and are principal components in rock classification schemes. The minerals included in this group are the orthoclase, microcline and plagioclase feldspars.
APPLICATIONS
Glass making
Ceramics
Porcelain
Electrodes
Abrasion
We at CEMENTATION produce Feldspar of minerals containing Potassium and Sodium. Our supply is available in Lumps, Granules and Powder form.
Quartz is the most abundant and most common mineral on the Earth. It is found in almost every geological environment and also it is at least a component of almost every rock type. It has a hexagonal crystal structure and is made of trigonal crystallized silica. It is most varied in terms of varieties, colours and forms.
The most important distinction between the types of quartz is that one is of macro crystalline, which is individual crystal visible to the unaided eye, and the other is microcrystalline or cryptocrystalline varieties, aggregates of crystals visible only under high magnification. Chalcedony is the generic term for cryptocrystalline quartz. The transparent variety tends to be microcrystalline and the cryptocrystalline varieties are either translucent or mostly opaque.
Bauxite is a naturally occurring mineral comprising mainly of aluminium hydroxides (the trihydrate Gibbsite Al(OH)3and the AlOOH monohydrate polymorphs boehmite and diaspore), with other components in the mineral typically being silica, iron oxide, titania and aluminosilicates (clay etc). It’s a rock from Laterite soil and it is a primary Ore of Aluminium.
Properties of Bauxite include low iron content; a high Polished Stone Value (PSV) for high friction surfacing applications; a high melting point and density.
APPLICATIONS
Gunning materials
High friction surfacing
Minerals for abrasion
Refractory castables
Mouldable and Ramming Mixes
Refractory mineral blends
CEMENTATION believes in supplying quality bauxite with consistency to its customers across the world, according to their needs.
418603 Fiberglass Mesh For Construction Suppliers
Short on time? Let Fiberglass Mesh For Construction sellers contact you.
