PPE material (called Polyphenylene Ether). PPE resin, exhibits low moisture absorption due to its inherent composition. Therefore, good electrical insulation properties will be achieved under temperature and humidity conditions. Chemical reaction from water, most salts, acids and bases is also minimal with PPE material. MATERIAL: PPE regrind black CATEGORY: PPE TYPE: regrind GRADE: black SPECIFICATION: Grade V-0, engineering plastic Origin: Japan LOADING WEIGHT: 25 Ton FOB (USD/Ton): 900$ - 1000$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days PPE Plastic Provides: Good electrical insulation properties Long term dimensional stability Outstanding impact resistance Light-weight Heat resistance Good hydrolysis stability
Naphtha is aromatic low density fuel consumed internally in refinery for production of Petrol and Hydrogen. Used as a feed, unutilized production is sold to petrochemical and other industries like fertilizers etc.
Origin: United Kingdom Material: LDPE Repro pellets Yellow Category: LDPE Type: Repro pellets Color: Yellow Quantity: 500 Tons Loading weight: 24 Tons Specification: "rLDPE repro Yellow pellets from post-consumer & post-industrial films. The material is shredded and washed through a wash plant before it is processed through degassing and very fine filtration to produce high purity reprocessed resin. toughness, strength and stretch properties. This grade is also be suitable for profile and sheet extrusion Packing: 1000kg bulk bag Melt flow rate (190�?C / 2.16kg) 0.5 � 0.5 Density 0.92 � 0.015 Measured on blown film of 25 �m and BUR of 2.5 at external testing facility. rLDPE Yellow is typically extruded at a melt temperature around 190�?C (min 180�?C, max 240�?C). Mesh filters: 150 on the laser filter and 120 on the piston filters."
POM regrind black color full container available POM plastic possesses the same priority features as other plastic polymers, some of the highlights of the special resin: High hardness Bearing good Low friction number High resistance to abrasion High temperature resistant Less water intake Has anti-static ability Dimensional stability, little change Less smoke burns when burning High glossy surface High crystallization In addition to the priority points, POM plastic also has some limited formats such as: Quality acid resistance and alkali High hatch rate when changing secretions Operation mode Heat range MATERIAL: POM regrind black color full container available CATEGORY: POM TYPE: Regrind GRADE: Black color SPECIFICATION: 1 full container available Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
Bauxite is a naturally occurring mineral comprising mainly of aluminium hydroxides (the trihydrate Gibbsite Al(OH)3and the AlOOH monohydrate polymorphs boehmite and diaspore), with other components in the mineral typically being silica, iron oxide, titania and aluminosilicates (clay etc). It’s a rock from Laterite soil and it is a primary Ore of Aluminium. Properties of Bauxite include low iron content; a high Polished Stone Value (PSV) for high friction surfacing applications; a high melting point and density. APPLICATIONS Gunning materials High friction surfacing Minerals for abrasion Refractory castables Mouldable and Ramming Mixes Refractory mineral blends CEMENTATION believes in supplying quality bauxite with consistency to its customers across the world, according to their needs.
Virgin & Recycled Low Density Polyethylene LDPE Granules
As one of professional producers of plastic and rubber raw material, We manufacture, distribute and export synthetic resin, synthetic rubber, and polymer. Also agent sinopec company's products. the synthetic resin products include low-density polyethylene (LDPE), high-density polyethylene (HDPE), linear low-density polyethylene (LLDPE), polypropylene (PP), polystyrene (PS), polyvinyl chloride (PVC) and acrylonitrile-butadiene-styrene (ABS),etc . The synthetic rubber products include IIR, SBR, BR and SBS, etc.We mainly export European ,America ,Russia ,and other markets. Product Name:Linear low Density Polyethylene (LLDPE) Grade: all Grades CAS NO.: 9002-88-4 Place of origin : China Mainland Color: Natural White or colorful 25kg/pp bag, 20mt/20'fcl 25mt/40'fcl
low oxygen Selenium Granules Size: 2-6mm.3-5mm,1-10mm or as required Molecular Formula - Se Molecular Weight - 78.96 Melting Point - 217 C Boiling Point - 684.9 + 1.0 C Relative Density - 4.81 g /cm3 Purity - 99.99% Appeaance - Black
Item Test condition Test Method Value Unit Density ISO 1183 0.944-0.955 g/cm3 MFR 190 C/2.16kg ISO 1133 0.03-0.07 g/10min Tensile strength at yield ISO 527-2 22 MPa Elongation at break ISO 527-2 >350 % ESCR F50,50 C,100% ASTM D-1693A 1000 h VICAT ASTM D-1525 126 C For extrusion packaging film, rope, woven bags, fishing nets, water pipes; injection of low-end commodity and housing, non-bearing load components, plastic box, turnover box; extrusion blow molding containers, hollow products, bottles.
Item Test condition Test Method Value Unit Density ISO 1183 0.944-0.955 g/cm3 MFR 190 C/2.16kg ISO 1133 0.03-0.07 g/10min Tensile strength at yield ISO 527-2 22 MPa Elongation at break ISO 527-2 >350 % ESCR F50,50 C,100% ASTM D-1693A 1000 h VICAT ASTM D-1525 126 C For extrusion packaging film, rope, woven bags, fishing nets, water pipes; injection of low-end commodity and housing, non-bearing load components, plastic box, turnover box; extrusion blow molding containers, hollow products, bottles.
Metal tin is mainly used in the manufacture of alloys. Tin and sulfur compounds - tin sulfide, which is similar in color to gold, is commonly used as a gold pigment. Tin's modern application is as a solder for the electronics industry. Used in various purities and alloys (often with lead or indium), tin solders have a low melting point, which makes them suitable for bonding materials. Standard ASTM B29-03, BS EN 12659:1999, GB/T 469 -2005 , Content Pb â?¥ 99.99 % Density 11.34 g / cm 2 Color Bluish Weight 35 kgs / lump, 55 kgs / lump Dimension 21" x 4" x 2.5" Package Standard Sea-worthy package, fixed by belt per ton Shape Rectangular Lump Application lead-acid storage batteries Ammunition, cable sheathing, and building construction materials counterweights, battery clamps cast products such as: bearings, ballast, gaskets, type metal, terne plate, and foil Container Size 20Gp - 2.352(width) *2.385 ( Height ) * 5.90 ( Inside length ) Meter 40Gp - 2.352(width) *2.385 ( Height ) * 11.8 ( Inside length ) Meter 40HQ - 2.352(width) *2.69 ( Width ) * 5.90 ( Inside length ) Meter
Olive oil and related products, a1 jet fuel, en 590, urea, linear alkylbenzene sulfonic acid (labsa), polypropylene, engine oil, benzene, vaseline, d2 5000ppm, ethanol, chemicals, polyethylene, sulfur, food and beverage, sugar, cement..Mandate and intermediary services
Product name:hd polyethylene lldpe linear low density polyethylene ldpe lldpe granules injection grade PP/PVC/ABS/PE Appearance:Linear low density polyethylene is a non-toxic, tasteless, odorless milky white particle with a density of 0.918~0.935g/cm3. Application:At present, lldpe plastic is mainly used in the field of film and packaging, through extrusion and blow molding process to produce plastic bags, garbage bags, industrial lining, agricultural film, protective film, etc., but also through injection molding and rotoplastic production process to make toys, refrigerated appliances, chemical reaction tanks, waste storage boxes and so on.
Physical property Standard Test Condition Units Values Specific Gravity GB/T 1033 g/cm3 0.920 Melt Flow Rate GB/T 3682 g/10min 2 Mechanical Properties Standard Test Condition Units Values Tensile Strength at Yield GB/T 1040 Mpa 10 Tensile Strength at Break GB/T 1040 Mpa 16 Elongation at Break GB/T 1040 % 8 Haze GB/T 2410 % 14 Fish Eyes (pcs/1520 cm 2 ) 0.8mm 0.4mm 2 10 LLDPE Low density polyethylene, also known as high pressure polyethylene (LDPE), is the lightest variety of polyethylene resin, is milky, tasteless, odorless, non-toxic, non-glossy surface waxy particles. It has good softness, extensibility, electrical insulation, transparency, workability and certain air permeability. Its chemical stability performance is good, alkali resistance, resistance to general organic solvents. Application range of low density polyethylene: suitable for seasoning, pastry, sugar, preserves, biscuits, milk powder, tea, fish floss and other food packaging. Tablets, powders and other medicine packaging, shirts, clothing, knitted cotton products and chemical fiber products packaging. Washing powder,detergent, cosmetics and other daily chemical products packaging. Because of the poor mechanical properties of single-layer PE film, it is usually used as the inner layer of composite packaging bag, that is, multilayer composite film heat-sealing substrate.
LLDPE is one of the major thermoplastics. It is a polyethylene with good impact and puncture resistance, good fexibility and high elongation under stress. The main application for LLDPE is films and sheets and is also used in injection-moulding, wire, and cables. LLDPE grades are butene-based, and its resins are produced through butene's copolymerization. LLDPE resins can improve mechanical and welding effciencies, including products for heavy duty bags, produce bags and agricultural bags. Examples of applications are bags, packaging film, agricultural fillm, stretch film, cling-film and lamination films. In packaging applications, it offers good aesthetics, printability, strength, and processing.
ES fiber is a sheath-core composite fiber obtained by successfully combining low-melting components and high-melting components on a single fiber. It has excellent thermal bonding properties. The low melting point component in ES fiber melts under heat treatment conditions higher than its melting point, and bond with other materials to form a binder-free environmentally and friendly non-woven fabric. ES fiber has various advantages such as soft, fluffy, low-temperature processing, heat-bonding, plasticity, non-toxic, non-irritating, and lightweight. It is mainly used to manufacture high-quality sanitary products such as sanitary napkins and diapers. And it is also high-quality materials used to make medical products such as medical protective cloth and medical protective masks, and so on. There are two main types of ES fibers. The first kind is a composite of PE and PP. Its sheath layer is PE (polyethylene, melting point 130�°C), and its core layer is PP (polypropylene, melting point 165�°C). The second kind is a composite of PE and PE. Its sheath layer is PE, and the core layer is PET (polyester, melting point 255â??), which is an upgraded version of PE/PP. ES is divided into EP and ET in terms of material and functionally divided into the hydrophilic, water-repellent, hydrophilic, and weak parent, single parent, multi-parent.In addition, it also can be divided into whitening, general whitening, high holding, medium holding, and low holding. The specifications are 1.5D38mm, 2D38mm, 4D51mm, and so on. In the future, the trend will gradually develop towards fine deniers. SPECIFICATION: PE+PET ES Fiber: Optical White & Super Hydrophile 2D*38mm, Optical White & Hydrophile 2D*38mmï¼? Optical White & Water Repellency 2D*38mmï¼? RAW White & Water Repellency 2D*38mmï¼? Optical White & Super Hydrophile 1.5D*38mmï¼? Optical White & Water Repellency 1.5D*38mmï¼? RAW White & Water Repellency 1.5D*38mï¼? Hydrophile 2D*38mmï¼? Water Repellency 2D*38mm PE+PP ES Fiber: Hydrophile (P2Q) 2D*38mm
Technical Data Sheet Of Accoset-50 ALUMINA MORTAR (Test Certificate) General Properties A. Max service temperature - 1500 oC B. Maximum grain size - 0 - 1.5 mm C. Water required for mixing - 22 - 30% D. Setting - Airsetting E. Sintering Temp - 1550 oC Chemical Properties A. Al2O3 - 50.00% B. SiO2 - 31.00% c. Fe2O3 - 5.00% D. LOI - 7.00% Physical Properties A. Dry Density - kg / m3 B. CCS - 17 kg / cm2 after drying at 110C / 24 hr C. MOR - 20 kg / cm2 at 110 oC/ 24 hr 18 kg/cm2 at 800 C/ 3 hr Thermal Properties - A. Refractoriness ( Orton / C) - 31.5 orton cone/1699 oC Packaging - 25 - 50 kg bags Storage Life - 12 months Delivery State - Dry
PVC (Vinyl) Glove US$ 5.88 - 8.85 / Box 1000000 Boxes Minimum Order 15 - 60 days Lead Time Product Details Model Number : S M L XL- Brand Name : WinHealth (Future) Origin : China (mainland) Small Orders : Accepted Key Specifications/Special Features: Vinyl gloves are made from PVC (Polyvinyl Chloride). Vinyl gloves are mostly used in working environment. These types of gloves are cheap. If you are allergic to latex gloves or to nitrile gloves then you can use our vinyl gloves. Though disposable vinyl gloves get fractured and punctured often. Sole purpose of these gloves is to work in general environment, but can be used for medical examination. It's a mixture of plastic material and it has low elasticity. Buy vinyl multipurpose gloves at cheap price. Features: Made from High quality Synthetic Polyvinyl Chloride Paste Resin Softer and more elastic than other vinyl gloves. Powder free to reduce potential dust contamination. 100% latex-free gloves eliminate allergic reaction to allergic protein. Textured surface provides strong grip for wet and dry applications. Superior puncture, tear and chemical resistance with excellent dexterity. For laboratory procedures where use of powder free gloves are recommended. Provides an alternative solution for individuals who are allergic to natural rubber latex. Standards: Biocomaptibility tested or biocompatibility friendly. Resists permeation by a widen range of chemicals as compared to synthetic vinyl of the same thickness. Manufactured under QSR (GMP) and ISO 9001: 2001 Quality Management System. Specifications: Used in: Medical, Dental, Laboratory, Food Sectors and Many More. Type: Non-sterile, Powder-free Material: 100% Synthetic Polyvinyl Cholride Paste Resin. Shape: Ambidextrous Beaded cuff No latex additives Glove sizes: Small, Medium, Large, Extra-large For single use only Color: Yellow 100 gloves per box,
Hibiscus TBC - Egyptian Hibiscus TBC - Red Roselle Family: Malvaceae Botanical name: Hibiscus Sabdariffa Common names: Dried Hibiscus flower l Hibiscus leaves l Red Hibiscus Flower l Hibiscus Sabdariffa l Roselle Hibiscus l Karkade l Carcade. Hs Code: 1211900014 Form: Tea bag granules Color: Red Application: Herbal tea. Sour: accepted ratio Taste: a great taste of Hibiscus iced or heated Amazing medical benefits of Dried Hibiscus flower (Red Roselle)? 1) it balances blood pressure. The American Heart Association (AHA) has proved, in its report dated November 2008, that the regular consumption of Hibiscus tea can lower blood pressure in pre-hypertensive and also mildly hypertensive adults. 2) it helps to lower cholesterol levels in the blood so it can be used to prevent heart diseases and protect blood vessels from damage. 3) it can help to cure blood sugar disorders such as diabetes. It is distinguished by the properties of hypolipidemic and hypoglycemic which enable it to reduce cholesterol, triglycerides, and low-density lipoprotein cholesterol. We are a family business company back to 1960, we are producing & dealing & exporting for over 25 countries worldwide. Ask the Specialist for quality Egyptian Hibiscus. Waiting your contact soon.
Polyethylene Low Melting Bag,single sheet thickness is 10-300 mic, melting point is 70-115?, various colors, printing, double seal thermal bonding insurance line are available. Anti-slipping, low melting valve automatic sealing technology.
