Fumed silica (CAS number 112945-52-5), also known as pyrogenic silica because it is produced in a flame, consists of microscopic droplets of amorphous silica fused into branched, chainlike, three-dimensional secondary particles which then agglomerate into tertiary particles. The resulting powder has an extremely low bulk density and high surface area. Its three-dimensional structure results in viscosity-increasing, thixotropic behavior when used as a thickener or reinforcing filler. Fumed silica has a very strong thickening effect. Primary particle size is 550 nm. The particles are non-porous and have a surface area of 50600 m2/g. The density is 160190 kg/m3. APPLICATION Paints and coatings Unsaturated polyester resins, laminating resins and gel coats HTV- and RTV-2K-silicone rubber Adhesives and sealants Printing inks Cable compounds and cable gels Plant protection Adhesives and sealants Chemical mechanical planarization (CMP) Coatings Composites Food additives Greases Pharmaceuticals Printing and packaging Silicone sealants Skin and beauty care product
PREPARATIONS The substrate, bolt and anchor holes must be clean, sound, dry and free of oil, grease, without laitance and loose particles. Prewet the bolt holes thoroughly, but no standing water in it. Before applying ITLS CA-007H absorbent substrates must be saturated thoroughly, but without standing water. MIXING Mix 3.2-4.4 liters of clean water with 25kg bag of ITLS CA-007H together. To add water based on the condition of stirring and keep stirring around 5 minutes until grouting well. APPLICATIONS Pour ITLS CA-007H mortar after mixing into the reserved cavities and recesses use the stick or bar to remove the air bubble, ensure that air entrapped into the grout is allowed to escape. Suggest to blend the grout by auto-mixer for better application. COVERAGE 25 Kg ITLS CA-007H when mixed with water will produce approx. 13.5 liters of Liquid Grouting Mortar. ITLS CA-007H suggest to be placed in thickness ranging from 10-15cm/layer.
Features * With excellent adhesion, non-sagging and construction resistance. * Without cracking and bulging after curing. * Specific design for spray plastering. * Applying by spraying machines efficiently. * Suitable for tiling. * Interior wall, exterior wall, panel wall and small area ceiling rendering. Application 1. Substrate must be free from grease, mould oil, rust, rusty metal , wood peels, paints, plastics, loose particles, contamination on any traces of foreign materials affecting the adhesion of CS-010. 2. Moisten the substrate overnight and also at the time before the commencement of operation. 3. Suggest to use CC-400 Concrete Bond as primer to adding adhesion for smooth and low porous substrates. 4. CS-010 is suitable for any type of spraying machine. Mix a packet of 40KG powder with 6.4liter of water and stir well for use. Its thickness should be maintained at 15mm and wait for 6-24 hours to apply for increasing the thickness. Storage Storage life is 12 months if the product is kept in a dry place. Package 40kg/powder bag
DESCRIPTION Cement Filler is used for exterior coating on the tiles, steel plate, a smooth surface or a low porosity material to combine the old surface and the new one. FEATURE * Water-based formulations of two special adhesive. * For tiles, steel, a smooth surface or a low porosity of the material surface ?¯ etc. * With waterproofing, impervious, weather resistance, freeze-thaw characteristics. * Can be used both on wet and dry surfaces. * With good adhesion. APPLICATION * To adhere and mix old concrete surface and new concrete surface * Can be used to adhere indoor and outdoor old cement walls, fiber cement board, tile, concrete, colored steel board, asbestos and various green compartment plates etc. WORKING PROCEDURE 1 All surfaces need to be clean, free from dust, rust, white birch and either grease. In addition, the concrete could be moistened but not with floating. 2. Coating CA-003M by brush, roller or spray on the substrates. The coverage would be 4 ~ 7m ² per kilograms which depends on the situation of porous and roughness of the substrates. 3 All the tools can be cleaned by water.
Wholesale Kitchen Linen at affordable Prices : * Chef's kitchen apron with pockets is made from breathable lightweight heavyduty cotton rich fabric. * Measures 26 x 35 inches. Multi purpose, stain resistant, durable apron with extra long waist strap & adjustable neck strap to fit most sizes. Premiuim professional apron suitable for chefs, bakers, housewives, artists, stylists, crafters, beautician, cosmetologist, grillmaster, bartender, barista, painters, carpenters, welders & more. * 2 spacious front pockets of these heavy duty aprons give you a place to hold onto seasoning packets, meat thermometer, grill slips and recipe cards. * Large bib canvas aprons cover from chest to knee. Flexible for use at home, cafe, bakery, restaurant, bistro, bar, salon, pub, outdoor & more. Provides protection from kitchen heat, grease and food stains * Unisex pocketed aprons make a great gift idea for birthdays, holidays and housewarming & bulk orders. * Single Pack * Solid/Stripe/Gingham * Check Apron * Cotton Rich Fabric * Purchaes by case only * 48 peice per case
CitroShield - Certified Natural & Organic Oven Cleaner (Ready To Use) is a heavy duty natural oven cleaner that does not contain any toxic ingredients. It can be used for all surface cleaning and degreasing of ovens and stoves in the home or industrial environments. It will remove all types of proteinaceous soils, fat encrusted soils, lime scale soils, fats, carbons, oils and grease. CitroShield - Certified Natural & Organic Oven Cleaner (Ready To Use). Ingredients: Demineralised water, non-ionic surfactant, sodium carbonate, citric acid, white vinegar, bitter orange extract (bioflavonoid complex). It has been certified as 100% Natural by Natural Verifiers, USA and Organic by the BFA and Australian Organic here in Australia. These certifications are evidence of the fact that this product does not contain any harmful chemicals or petrochemicals and is therefore, non-hazardous, non-corrosive, non-carcinogenic and totally safe. For use on ovens, Chimneys, Stoves, Exhaust Canopies and barbeques. Benefits: -Natural & Organic -Child safe/Pet safe -Not tested on animals -No petrochemicals -Proven cleaning power -Kills 99.99% germs -99.99% biodegradable -Easy to Use -Stubborn stain remover -Non-corrosive -Phosphate free -Totally non-toxic -No harmful chemicals -Environmentally friendly -Gentle on hands -Leaves no soapy residue
We make open mixing mill models from XK-160 to XK-610 Usage: For rubber & plastic compound mixing and sheeting Model: X(S)K-160X320 X(S)K-230X635 X(S)K-250X635 X(S)K-300X700 X(S)K-360X900 X(S)K-360X900 X(S)K-400X1000 X(S)K-450X1200 X(S)K-550X1500 X(S)K-610X1730 What are the options and configurations? 1. Driving system: Bull gear drive, single shaft output or double shaft output for your choice. 2. Roller gap adjustment: by manual or electrical (motor drive) for your choice. 3. Roller support: by nylon bush or bearing rolls for your choice. 4. Lubrication system: by grease or oil pump for your choice. 5. Stock guider: movable, fixed or hydraulic for your choice. 6. Gear reducer: ZSY harden tooth reducer. 7. Electrical components brand: CHINT, Schneider or Siemens, etc. for your choice. 8. Stock blender optional.
ts of Aluminum Magnesium-Silicon alloy wires stranded in successive layers in opposite direction and the outer layer is right hand direction Z. Natural grease may be applied between the layers of AAAC except the outer layer. STAQNDARD Construction as per ASTM B399, DIN 48201, BS EN 50182, IEC 61089, CSA C49. APPLICATION: AAAC bare conductors are used for primay and secondary overhead power transmission lines having long spans and high resistance to corrosion. Detailed Product Description AAAC (All Aluminum Alloy Conductor) referred to have higher strength but lower conductivity than pure aluminum. Being lighter, alloy conductors can sometimes be used to advantage in place of the more conventional ACSR; Having lower breaking loads than the latter, their use becomes particularly favourable when ice and win loadings are low. We can supply this conductor according to different recognized standards, such as BS EN50182, IEC61089, ASTM B399DIN 48, customer special specification also can be satisfied.
7200 ACD/P4A Dimensions d 10 mm D 30 mm B 9 mm d 1 17.3 mm d 2 17.3 mm D 1 23.1 mm r 1,2 min. 0.6 mm r 3,4 min. 0.3 mm a 9.3 mm Abutment dimensions d a min. 14.2 mm d b min. 14.2 mm D a max. 25.8 mm D b max. 27.6 mm r a max. 0.6 mm r b max. 0.3 mm d n 18.3 mm Calculation data Basic dynamic load rating C 4.36 kN Basic static load rating C 0 1.86 kN Fatigue load limit P u 0.078 kN Attainable speed for grease lubrication 53000 r/min Attainable speed for oil-air lubrication 80000 r/min Ball diameter D w 4.762 mm Number of balls z 10 Reference grease quantity G ref 0.357 cm�³ Preload and stiffness (back-to-back, face-to-face) Preload class A G A 27 N Static axial stiffness, preload class A 35 N/�µm Preload class B G B 54 N Static axial stiffness, preload class B 45 N/�µm Preload class C G C 108 N Static axial stiffness, preload class C 59 N/�µm Preload class D G D 216 N Static axial stiffness, preload class D 78 N/�µm Calculation factors Calculation factor f 1.02 Calculation factor f 1 0.99 Calculation factor f 2A 1 Calculation factor f 2B 1.01 Calculation factor f 2C 1.02 Calculation factor f 2D 1.05 Calculation factor f HC 1 Calculation factor e 0.68 Calculation factor (single, tandem) Y 2 0.87 Calculation factor (single, tandem) Y 0 0.38 Calculation factor (single, tandem) X 2 0.41 Calculation factor (back-to-back, face-to-face) Y 1 0.92 Calculation factor (back-to-back, face-to-face) Y 2 1.41 Calculation factor (back-to-back, face-to-face) Y 0 0.76 Calculation factor (back-to-back, face-to-face) X 2 0.67 Mass Mass bearing 0.032 kg
DESCRIPTION ITSEAL is truly developed for sealing window frames with highly durable and flexible properties to withstand severe weathering and extreme temperatures. It seals small gap that normal sealant cannot reach and penetrate. It provides a truly watertight seal deep into minute joint and gap. FEATURES * ITSEAL is the only waterproof sealer that is completely watertight. * It is highly water repellent that no water can get through it during storm. * It adheres well on aluminum and glass * Once dried, ITSEAL is flexible and accommodate joint movement due to vibration. * Mill finish aluminum, oil or wet surfaces can also be well-sealed. VOC CONTENT Type of Regulated Adhesive under the Air Pollution Control (Volatile Organic Compounds) Regulation of Hong Kong: Architectural Sealant VOC Content (Ready to use): 248g/Ltr. SURFACE PREPARATION For maximum adhesion, the adhesive surface must be free of dust, release agent, oil and grease. Wipe surface with solvent is recommended. Solvent are obtainable from ITLS-SB. This information in this catalogue is provided to the best of our knowledge from results gathered both internal and external credited laboratories. However, we have no control over site applications, site conditions and workmanship of the applicator. We therefore will not accept any liability, either directly or indirectly arising from the misuse of these products or when the product is used not in accordance with any advice, specification, and recommendation of information given by us, The user is responsible for checking the suitability of these products for its intended use. APPLICATION ITSEAL can be used with hand operated or air operated grease pump. Other simple extruding device can also be used but it has to be solvent resistance. LIMITATION * Not suitable large gap wider than 5 mm wide and deep. For deeper joint fill to half of it, let it dry overnight and fill it up the next day. * Not suitable for use as expansion joint. COLOUR AND PACKING 26 kg / pail Grey/Black/Bronze/White SAFETY INFORMATION * ITSEAL is flammable. Please keep away from sources of ignition during application. * Avoid breathing in solvent by wearing solvent vapor respiratory mask in badly ventilated area or confined space. * Avoid contact with skin and eyes. If swallowed please contact doctor immediately. * ITSEAL meets the requirement of RoHS regulation of European Union and it does not contain eight heavy metals which were restricted by ASTM F963 or EN71 part3. * Please read the Material Safety Data Sheet in regards to flammability and health and hazard. SHIPPING/STORAGE INFORMATION ITSEAL must be stored in a cool place under 25°C and away from direct sunlight. The shelve life is 12 months if stored in accordance to the recommendation. Dangerous Goods Information: Cement Adhesive, Class 3, UN1133 PG III.
SIDA Factory KBQX-30SG high performance single hose pipe dry ice blasting machine, dry ice blaster, dry ice cleaning machine Cleaning Principle: Dry ice blast cleaning machine is the use of high-speed flow of compressed air mixed with dry ice pellets particles, through the spray gun nozzle into cleaning subject, make the surface fouling engine-grease produce cold crack, delaminating, was finally a cleaning method of impact stripping. The cleaning method belong to dry cleaning, dry ice will be instant vaporization, no residue, do not produce secondary waste, can be directly clean the production line without affect, the force is relatively weak compare to sandblast, it is non-destructive decontamination, does not hurt the equipment and damage of the mould. Technical Parameters: Model no.: KBQX-30SG dry ice blaster Raw material: 1.5~3 mm dry ice pellets Capacity of dry ice loading: 30 kg Dry ice flow: 0~1.5 kg/min (adjustable) Air pressure: 0.4~0.8 Mpa (adjustable) Air flow: 2.5~4 m3/min Blasting gun hosepipe: 5 m Size (L*W*H): 300*420*800 mm Total weight: 40kg Features of our dry ice blaster: 1. This machine used the technology cooperated with ITALY MEC company. 2. Small and the weight is less than half of the single pipe type, perfect for small space operation. 3. Pneumatic control, no electricity used, perfect for inflammable, explosive and field work. 4. Shell and hopper are stainless steel with good corrosion resistance.The hopper is equipped a vibrating feeding device to ensure reliable and smooth dry ice conveying. 4. The nozzle handle is safe to control, as soon as the spray is released, the spraying process stops immediately. 5. The amount of dry ice spray can be adjusted to save ice. Application of dry ice cleaning machine: 1.Especially suitable for the blast cleaning of tire mould, polyamine grease mould, automobile interior trim mold, plastic mold cleaning. 2. For petrochemical heating furnace tube coke blast cleaning. 3. Blast cleaning of mold coating for casting sand mold 4. For Food baking equipment, hotel kitchen, tar, and blast cleaning; 5. For transformer and transmission station equipment blast cleaning 6. Blast cleaning of acid and alkali pollution equipment. 7. Various equipment renovation and complex shape equipment appearance dirt blast cleaning. 8. It is particularly suitable for situations where water and sand can not be washed.
SIDA Factory KBQX-30SG high performance single hose pipe dry ice blasting machine, dry ice blaster, dry ice cleaning machine Cleaning Principle: Dry ice blast cleaning machine is the use of high-speed flow of compressed air mixed with dry ice pellets particles, through the spray gun nozzle into cleaning subject, make the surface fouling engine-grease produce cold crack, delaminating, was finally a cleaning method of impact stripping. The cleaning method belong to dry cleaning, dry ice will be instant vaporization, no residue, do not produce secondary waste, can be directly clean the production line without affect, the force is relatively weak compare to sandblast, it is non-destructive decontamination, does not hurt the equipment and damage of the mould. Technical Parameters: Model no.: KBQX-30SG dry ice blaster Raw material: 1.5~3 mm dry ice pellets Capacity of dry ice loading: 30 kg Dry ice flow: 0~1.5 kg/min (adjustable) Air pressure: 0.4~0.8 Mpa (adjustable) Air flow: 2.5~4 m3/min Blasting gun hosepipe: 5 m Size (L*W*H): 300*420*800 mm Total weight: 40kg Features of our dry ice blaster: 1. This machine used the technology cooperated with ITALY MEC company. 2. Small and the weight is less than half of the single pipe type, perfect for small space operation. 3. Pneumatic control, no electricity used, perfect for inflammable, explosive and field work. 4. Shell and hopper are stainless steel with good corrosion resistance.The hopper is equipped a vibrating feeding device to ensure reliable and smooth dry ice conveying. 4. The nozzle handle is safe to control, as soon as the spray is released, the spraying process stops immediately. 5. The amount of dry ice spray can be adjusted to save ice. Application of dry ice cleaning machine: 1.Especially suitable for the blast cleaning of tire mould, polyamine grease mould, automobile interior trim mold, plastic mold cleaning. 2. For petrochemical heating furnace tube coke blast cleaning. 3. Blast cleaning of mold coating for casting sand mold 4. For Food baking equipment, hotel kitchen, tar, and blast cleaning; 5. For transformer and transmission station equipment blast cleaning 6. Blast cleaning of acid and alkali pollution equipment. 7. Various equipment renovation and complex shape equipment appearance dirt blast cleaning. 8. It is particularly suitable for situations where water and sand can not be washed.
Refined Castor Oil..
Grade A Cold Pressed, Hexane Free Organic Castor Oil..
FSG Castor Oil..
Castor oil.
Virgin Cold Pressed Castor Oil, Unrefined, Hexane Free..
castor oil.
Jamal Agri Farms (Jaf) Castor Oil..
Virgin Cold Pressed Castor Oil, Unrefined, Hexane Free..